1999 MITSUBISHI LANCER EVOLUTION VI wiring

SRS – Air Bag Module Disposal Procedures52B-33
3. Peform the following procedure to deploy each air bag
module.

(1) Remove the steering column cover lower.
(2) Remove the connection between the clock spring
2-pin connector (red) and the body wiring harness
connector.
NOTE
If the clock spring connector is disconnected from
the body wiring harness, both electrodes of the clock
spring connector will be automatically shorted to
prevent unintended deployment of the air bag due
to static electricity, etc.
(3) Connect two wires, each six meters or longer, to the
two leads of SRS air bag adapter harness A and
cover the connections with insulation tape. The other
ends of the two wires should be connected to each
other (short-circuited), to prevent sudden unexpected
deployment of the air bag.
(4) Connect the clock spring or air bag module (front
passenger’s side) 2-pin connector (red) to SRS air
bag adapter harness A and pass the deployment
wires out of the vehicle.
(5) Shut all the doors with their window glasses closed
and cover the vehicle with a body cover to suppress
explosion noise leaks as much as possible.
Caution
Be sure to wrap the vehicle entirely in a body cover,
otherwise damaged glass panes could break into
fragments, bringing about a very dangerous situation.
(6) At a location as far away from the vehicle as possible,
disconnect the two connected wires from each other,
and connect them to the two terminals of the battery
(which has been removed from the vehicle) to deploy
the air bag.
Clock spring 2-pin
connector (red)
Body wiring harness
connector (2-pin)
SRS air bag
adapter
harness A
MB686560Connection
6 m or
longer
Two wires Insulation
tape
SRS air bag adapter
harness A
MB686560
2-pin connector (red)
Deployment wires
Body cover
Deployment
wire harness

SRS – Air Bag Module Disposal Procedures52B-35

(1) Remove the glove box. (Refer to P.52B-27.)
(2) Remove the connection between the air bag module
(front passenger’s side) connector (red 2-pin) and
the body wiring harness connector.
(3) Connect two wires, each six meters or longer, to the
two leads of SRS air bag adapter harness A and
cover the connections with insulation tape. The other
ends of the two wires should be connected to each
other (short-circuited), to prevent sudden unexpected
deployment of the air bag.
(4) Connect the clock spring or air bag module (front
passenger’s side) 2-pin connector (red) to SRS air
bag adapter harness A and pass the deployment
wires out of the vehicle.
(5) Shut all the doors with their window glasses closed
and cover the vehicle with a body cover to suppress
explosion noise leaks as much as possible.
Caution
Be sure to wrap the vehicle entirely in a body cover,
otherwise damaged glass panes could break into
fragments, bringing about a very dangerous situation.
(6) At a location as far away from the vehicle as possible,
disconnect the two connected wires from each other,
and connect them to the two terminals of the battery
(which has been removed from the vehicle) to deploy
the air bag.
Body wiring harness
connector
(2-pin)
Air bag module 2-pin
connector (red)
SRS air bag
adapter
harness A
MB686560Connection
6 m or
longer
Two wires Insulation
tape
SRS air bag adapter
harness A
MB686560
2-pin connector (red)
Deployment wires
Body cover
Deployment
wire harness

54-1
CHASSIS
ELECTRICAL
CONTENTS
GENERAL 3. . . . . . . . . . . . . . . . . . . . . . . . . .
BATTERY 3. . . . . . . . . . . . . . . . . . . . . . . . . . .
SERVICE SPECIFICATION 3. . . . . . . . . . . . . . .
ON-VEHICLE SERVICE 3. . . . . . . . . . . . . . . . . .
IGNITION SWITCH EVOLUTION-VI WITH IMMOBILIZER
SYSTEM> 6. . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOL 6. . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING 6. . . . . . . . . . . . . . . . . . . .
IGNITION SWITCH 11. . . . . . . . . . . . . . . . . . . . . .
IGNITION SWITCH AND IMMOBILIZER
SYSTEM IMMOBILIZER SYSTEM> 13. . . . . . . . . . .
SPECIAL TOOL 13. . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING 13. . . . . . . . . . . . . . . . . .
IGNITION SWITCH AND IMMOBILIZER
SYSTEM 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
COMBINATION METERS 22. . . . . . . . . . . .
SERVICE SPECIFICATIONS 22. . . . . . . . . . . .
SEALANT 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS 23. . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING 24. . . . . . . . . . . . . . . . . .
CONTINUED ON NEXT PAGE
WARNINGS REGARDING SERVICING OF SUPPLEMENTAL RESTRAINT SYSTEM (SRS) EQUIPPED VEHICLES
WARNING!
(1) The service personnel must thoroughly review this manual, and especially its GROUP 52B – Supplemental Restraint
System (SRS) before beginning any service or maintenance of any component of the SRS or any SRS-related
component.
(2) When removing or installing the components indicated in the table of contents by an astarisk (*), use utmost care so
as not to apply any strong shock to SRS components.
NOTE
The SRS includes the following components: SRS-ECU, SRS warning lamp, air bag module, clock spring and interconnecting
wiring. Other SRS-related components (that may have to be removed/installed in connection with SRS service or maintenance) are
indicated in the table of contents by an asterisk (*).

CHASSIS ELECTRICAL – Ignition Switch and Immobilizer System54-20
REMOVAL SERVICE POINTS
ASTEERING LOCK CYLINDER REMOVAL
1. Insert the key in the steering lock cylinder and turn it
to the “ACC” position.
2. Using a cross-tip (+) screwdriver (small) or a similar tool,
push the lock pin of the steering lock cylinder inward
and then pull the steering lock cylinder toward you.
INSPECTION
IGNITION SWITCH CONTINUITY CHECK
1. Remove the column cover lower and upper.
2. Disconnect the wiring connector from the ignition switch.
3. Operate the switch, and check the continuity between
the terminals.
Ignition key Terminal No.Ignition key
position
12356
LOCK
ACC
ON
START
IGNITION KEY RING ANTENNA CONTINUITY CHECK
Use a circuit tester to check the continuity between the
terminals.
Cross-tip (+)
screwdriver

CHASSIS ELECTRICAL – Radio and Tape Player54-45
RADIO AND TAPE PLAYER
TROUBLESHOOTING
There is noise when the engine is running.
Kind of Noise (Parenthe-
sized is how noise
sounds.)SymptomCauseRemedy
AM, FM: Ignition noise
(Popping, snapping,
crackling, buzzing)
Popping sound becomes
faster with the increase
of engine speed.

The noise is lost with
ignition switch turned to
ACC.
Mainly due to the
spark plugs.

Due to noise circula-
tion from elsewhere

Noise from the engineCheck the noise capacitor
and earth cable and
replace if necessary. (See
Fig. 1 and Fig. 2.)
AM, FM: Defogger noise
(1) (Murmuring)Occurs when the defogger
switch is turned to ON and
OFF.Noise produced by spark-
ing when the defogger
switch is turned to ON/
OFF enters the glass
antenna.Check the noise capacitor
and replace if necessary.
(See Fig. 1.)
AM, FM: Defogger noise
(2) (Snapping noise)Occurs when the defogger
switch is turned to ON.Noise produced by current
flowing in the defogger
enters the glass antenna.Check the choke coil and
replace if necessary.
(See Fig. 3.)
AM, FM: Defogger noise
(3) (Scratching, gaggling)Occurs when the defogger
switch is turned to ON with
print heater wire broken.Noise produced by spark-
ing where print heater is
broken enters the glass
antenna.Repair the print heater.
AM, FM: Wiper motor
noise (Humming, wheez-
ing)Sound becomes faster with
the increase of wiper speed
and is lost when the wiper is
stopped.Caused by sparking in
wiper motor brush.Replace the wiper motor.
FM: Mirror motor noise
(Humming, wheezing)Occurs when electric mirror
operates.Caused by sparking in
mirror motor brush.Replace the electric
motor.
Other electrical compo-
nents–Noise is emitted by some
electrical components in
long use.Repair or replace electri-
cal components.
Static electricity (Crack-
ling, crinkling)
Noise is stopped when
the vehicle comes to a
complete stop.

Noise becomes louder
when the clutch is
released.Occurs when parts or
wiring move for some
reason and contact metal
parts of the body.Put parts or wiring into
position.
Various noises are produced
by body parts.Due to electrical detach-
ment of the hood, exhaust
pipe and muffler, suspen-
sion, etc. from the body.Tighten mounting bolts
securely. In many cases,
remedy of one part does
not eliminate the problem
due to incomplete earthing
elsewhere.
Caution
(1) Never let the noise filter contact a high tension cable. The noise filter could break down.
(2) Check that there is no external noise. This check is necessary to prevent misidentification of noise
sources.
(3) Noise prevention should be performed by eliminating noise sources in the descending order of loudness.

FULL-AUTOMATIC AIR CONDITIONER – Troubleshooting55-50
Inspection procedure 13
Condenser fan does not operate.
Probable cause
If the condenser fan does not turn when the A/C is ON, the cause is probably
a malfunction of the condenser fan motor activation circuit. In this case, reduced
cooling performance will be caused if the vehicle is not running.
Malfunction of condenser fan motor

Malfunction of condenser fan motor relay (HI, LO)

Malfunction of wiring harness or connector
NG
Repair OK
Check the trouble symptom.
NG
Check the harness between the condenser fan motor relay (LO)
and the condenser fan motor, and repair if necessary.
NG
Repair
OK
Check the trouble symptom.
NG
Check the harness between the condenser fan motor relay (LO)
and the body earth, and repair if necessary.
OK
Measure at the condenser fan motor relay (LO) connector A-113X.

Disconnect the connector.
(1) Continuity between terminal (4) and body earth
OK:Continuity
(2) Voltage between terminal (2) and body earth
OK:System voltage
(3) Voltage between terminal (1) and body earth
OK:System voltage(1) NGCheck the following connector:
A-113X
Condenser fan motor check (Refer to P.55-29.)NG
Replace
NG
Repair
OK
Check the trouble symptom.
NG
Check the harness between the condenser fan motor relay (LO)
and the A/C-ECU, and repair if necessary.
(2) NG
Check the following connector:
A-113X
NG
Repair
OK
Check the trouble symptom.
NG
Check the harness between the condenser fan motor relay (LO)
and the fusible link 2, and repair if necessary.
(3) NG
Check the following connector:
A-113X
OK
Continued to the next page
OK
Measure at the condenser fan motor connector A-99.

Disconnect the connector, and measure at the harness
side connector.

Connect the connector A-113X terminal (2) to the battery.

Voltage between terminal (2) and body earth
OK:System voltageNGCheck the following connector:
A-113X
OK
Condenser fan motor relay check (Refer to P.55-14.)NG
Replace

C-1
ELECTRICAL
WIRING
(R.H. DRIVE VEHICLES)
CONTENTS
GENERAL 3. . . . . . . . . . . . . . . . . . . . . . . . . .
WIRING HARNESS CONFIGURATION
DIAGRAMS 4. . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE COMPARTMENT 4. . . . . . . . . . . . . . . .
DASH PANEL 8. . . . . . . . . . . . . . . . . . . . . . . . . . .
FLOOR AND ROOF 12. . . . . . . . . . . . . . . . . . .
LUGGAGE COMPARTMENT 14. . . . . . . . . . . .
SINGLE PART INSTALLATION
POSITION 16. . . . . . . . . . . . . . . . . . . . . . . . .
RELAY 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ECU 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SENSOR 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SOLENOID AND SOLENOID VALVE 19. . . .
INSPECTION CONNECTOR 20. . . . . . . . . . . .
FUSIBLE LINK AND FUSE 20. . . . . . . . . . . . .
EARTH CABLE 21. . . . . . . . . . . . . . . . . . . . . . . .
EARTH 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CIRCUIT DIAGRAM 23. . . . . . . . . . . . . . . .
CENTRALIZED JUNCTION 23. . . . . . . . . . . . .
POWER DISTRIBUTION SYSTEM 24. . . . . .
STARTING SYSTEM 29. . . . . . . . . . . . . . . . . . .
IGNITION SYSTEM 30. . . . . . . . . . . . . . . . . . . .
CHARGING SYSTEM 31. . . . . . . . . . . . . . . . . .
MPI SYSTEM 32. . . . . . . . . . . . . . . . . . . . . . . . . .
COOLING SYSTEM 38. . . . . . . . . . . . . . . . . . . .
HEADLAMP 40. . . . . . . . . . . . . . . . . . . . . . . . . . .
TAIL LAMP, POSITION LAMP, LICENCE
PLATE LAMP AND LIGHTING MONITOR
BUZZER 42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ROOM LAMP AND LUGGAGE
COMPARTMENT LAMP 45. . . . . . . . . . . . . . . .
IGNITION KEY CYLINDER ILLUMINATION
LAMP 46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TURN-SIGNAL LAMP AND
HAZARD WARNING LAMP 48. . . . . . . . . . . . .
CONTINUED ON NEXT PAGE

– Engine Compartment WIRING HARNESS
CONFIGURATION DIAGRAMS
Connector
symbol
–01
thru
–50
A
Earth cable
C-4
WIRING HARNESS CONFIGURATION DIAGRAMS
ENGINE COMPARTMENT
A-01 (2-B) Brake fluid level switch
A-03 (1-B) Noise condenser
A-04 (1) Alternator
A-05 (4-GR) Alternator
A-09 (1-B) Starter
A-10 (1) Starter
A-12 (2-B) Fuel pressure solenoid valve
A-16 (4-B) Throttle position sensor
A-18 (6-B) Idle speed control servo
A-19 (3-B) Vehicle speed sensorA-20 (4-B) Windshield wiper motor
A-21 (8-B) Hydraulic unit
A-22 (2-B) Hydraulic unit
A-23 (2-B) Waste gate solenoid valve
A-25 (7-B) Air flow sensor
A-26 (2-B) Front speed sensor (LH) ABS>
A-28 (10-B) Control harness and front harness
combination