1999 LEXUS SC300 garage door opener

SECTION 1 ± 4
65
INSTRUMENTS AND CONTROLS
Interior equipment
Vanity mirrors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
.
65
Interior light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. .
66
Personal lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
.
67
Ignition switch light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
68
Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . . . . .
69
Cigarette lighter and ashtray . . . . . . . . . . . . . . . . . . . . . . . . . .
69
Glovebox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . .
72
Garage door opener 73
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cup holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . .
76
Floor mat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . \
. . . . .
78
Luggage stowage precautions . . . . . . . . . . . . . . . . . . . . . . . . .
80
VANITY MIRRORS

INTERIOR EQUIPMENT
73
GARAGE DOOR OPENER
The garage door opener is manufactured under license
from HomeLink and can be programmed to operate
garage doors, estate gates, security lighting, etc.
(a) Programming HomeLink
The HomeLink has 3 buttons and can be pr ogrammed to
operate 3 separate devices.
Prepare the HomeLink
 for programming by erasing all
codes or the memorized data programmed by the former
owner. Follow the procedure in º(c) Erasing the garage
door opener memoryº.
1. Decide which one of the 3 buttons you want to program.
Push and hold down the button for about 20 seconds until the
indicator light begins to flash. While holding this button,
follow steps º2º and º3º.

INTERIOR EQUIPMENT
742. Bring the hand held garage door opener within about 25
mm (1 in.) of the button being programmed and push the
button on the hand held garage door opener. The signal from
the hand held garage door opener is sent to the vehicle's
opener.
3. When the frequency and code is registered, the indicator
light flashes rapidly. At this point, you can release both
buttons.
4. To program the remaining buttons, repeat steps º1º
through º3º.
If you want to replace an existing program with a new
program, select the button you want to program. Follow the
procedure from step 1.
If the transmitter has a ºrolling code featureº, it is
necessary to program the in±garage receiver after
programming
HomeLink
.
1. Locate the ºtrainingº or ºlearningº button on the
in±garage receiver and push and release this button.
Location of the button may vary by the garage door
opener manufacturer.
2. Firmly push and release the trained HomeLink
 button
2 times (some garage door manufacturer may r equire you
to push the HomeLink
 button up to 3 times) to complete
the process.
The garage door should now operate when the
HomeLink
 button is pushed. Do not use the HomeLink
 universal transmitter with any
garage door opener that lacks the safety stop and reverse
feature as required by Federal Safety Standards. This
includes any garage door opener model manufactured before
April 1, 1982.

INTERIOR EQUIPMENT
75
CAUTION
When programming or operating the garage door opener,
make sure there is no one around the moving door. It is
dangerous if someone is caught.
(b) Operating the garage door opener
Push the appropriate button to activate the garage door
opener. The indicator light comes on. The garage door
opener continues to send the signal for up to 20 seconds as
long as the button is pushed.
(c) Erasing the garage door opener memory
Push and hold down the 2 outside buttons for about 20
seconds until the indicator light flashes. All memorized data
will be erased.FCC ID: CB2V94800
This device complies with FCC Rules part 15.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference that
may be received, including interference that may
cause undesired operation. WARNING: This
transmitter has been tested and complies with
FCC and DOC/MDC rules. Changes or
modifications not expressly approved by the
partly responsible for compliance could void the
user's authority to operate the device.