1999 LEXUS SC300 ABS

GAUGES, METERS AND SERVICE REMINDER INDICATORS
57
The light may occasionally flicker when the engine is idling
or it may come on briefly after a hard stop. There is no cause
for concern if it then goes out when the engine is accelerated
slightly.
The light may come on when the oil level is extremely low.
It is not designed to indicate low oil level, and the oil level
must be checked using the oil level dipstick.
NOTICE
Do not drive the vehicle with the warning light on ± even
for one block. It may ruin the engine.
(f) Low Engine Oil Level Warning Light
This light warns that the engine oil level is too low. Add oil
as soon as possible. (For instructions, see ºChecking the
engine oil levelº on page 342.)
While driving on steep inclines or rough roads which causes
the vehicle to substantially sway or on curves, this light may
come on due to the movement of engine oil in the engine.
NOTICE
Continued engine operation with low engine oil will
damage the engine.
(g) Malfunction Indicator Lamp
This lamp comes on in the following cases.
a. The fuel tank is completely empty. (See ºFuel gaugeº on
page 49 for instructions.)
b. The fuel tank cap is not tightened securely (SC400 only).
(See ºFuel tank capº on page 85 for instructions.)
c. There is a problem
somewhere in your engine or automatic
transmission electrical system.
If it comes on while you are driving in case ºc.º, have your
vehicle checked/repaired by your Lexus dealer as soon as
possible.
(h) ºABSº Warning Light
This light warns that there is a problem somewhere in your
anti±lock brake system.
If the light comes on while you are driving, have your vehicle
checked by your Lexus dealer as soon as possible.
The light will come on when the ignition key is turned to
ºONº, and will go off after about a few seconds.
When the ºABSº warning light is on (and the brake system
warning light is off), the brake system operates
conventionally but anti±lock brake system is not assisting
brake performance so that the wheels could lock up during a
sudden brake or braking on slippery road surfaces.

COMFORT ADJUSTMENT
133
The airbag sensor assembly consists of a safing sensor and
airbag sensor.
In a severe frontal impact, sensors detect deceleration and the
system triggers the airbag inflators. Then a chemical reaction
in the inflators momentarily fills the airbags with non±toxic
gas to help restrain the forward motion of the occupants.
When the airbags inflate, they produce a fairly loud noise.
And the driver airbag also releases some smoke and residue
along with non±toxic gas. This does not indicate a fire. This
gas is normally harmless, however, for those who have
delicate skin, it may cause minor skin irritation. Be sure to
wash off any residue as soon as possible to prevent minor skin
irritation.
Deployment of the airbags happens in a fraction of a second,
so the airbags must inflate with considerable force. While the
system is designed to reduce serious injuries, it may also
cause minor burns or abrasions and swellings. Parts of the airbag module (steering wheel hub, dashboard)
may be hot for several minutes, but the airbags themselves
will
not be hot. The airbags are designed to inflate only once.
A crash severe enough to inflate the airbags may break the
windshield as the vehicle buckles. In vehicles with a
passenger airbag the windshield may also be damaged by
absorbing some of the force of the inflating airbag.

STARTING AND DRIVING
250
Anti±lock brake system
The anti±lock brake system is designed to automatically
help prevent lock±up of the wheels during a sudden brake
or braking on slippery road surfaces. This assists in
providing directional stability and steering performance
of the vehicle under these circumstances.
The anti±lock brake system becomes operative after the
vehicle has accelerated to a speed in excess of approximately
10 km/h (6 mph). It stops operating when the vehicle
decelerates to a speed below approximately 5 km/h (3 mph).
You may hear a sound in the engine compartment for a few
seconds when the engine is started or just after the vehicle is
started. This means that the anti±lock brake system is in the
self±check mode, and does not indicate a malfunction.
Effective way to press the ABS brake pedal: When the anti±
lock brake system function is in action, you may feel the brake
pedal pulsating and hear a noise. In this situation, to let the anti±
lock brake system work for you, just hold the brake pedal down
more firmly. Do not pump the brake in a panic stop. Pumping the
brake pedal makes the stopping distance longer.

STARTING AND DRIVING
252ºABSº warning light

STARTING AND DRIVING
253
This light comes on when the ignition key is turned to the
ºONº
position. After about a few seconds, the light will go
off.
If either of the following conditions occurs, this indicates a
malfunction somewhere in the parts monitored by the
warning light system. Contact your Lexus dealer as soon as
possible to service the vehicle.
 The light does not come on as described above, or remains
on.
 The light comes on while driving.
Even if the anti±lock brake system should fail, the brake
system will still operate conventionally. But when the ºABSº
warning light is on (and the brake system warning light is off),
anti±lock brake system is not assisting brake performance so
that the wheels could lock up during a sudden brake or
braking on slippery road surfaces. Have your vehicle
checked by your Lexus dealer as soon as possible.
Drum±in±disc type parking brake system
Your vehicle has a drum±in±disc type parking brake system.
This type of brake system needs bedding±down of the brake
shoes periodically or whenever the parking brake shoes
and/or drums are replaced.
Have your Lexus dealer perform the bedding±down.

DRIVING TIPS
268

Because of the added load of the trailer, your vehicle's
engine may overheat on hot days (at temperatures over
30C [85 F]) when going up a long or steep grade with a
trailer. If the engine coolant temperature gauge indicates
overheating, immediately turn off the air conditioning (if
in use), pull your vehicle off the road and stop in a safe
spot. See ºIf your vehicle overheatsº on page 280 of this
manual.

Always place wheel blocks under both the vehicle and
trailer wheels when parking. Apply the parking brake
firmly. Put the transmission in ºPº. Avoid parking on a
slope with a trailer, but if it cannot be avoided, do so only
after performing the following:
1. Apply the brakes and keep them applied.
2. Have someone place wheel blocks under both the vehicle
and trailer wheels.
3. When the wheel blocks are in place, release your brakes
slowly until the blocks absorb the load.
4. Apply the parking brake firmly.
5. Shift into ºPº and turn off the engine.
When restarting out after parking on a slope:
1. With the transmission in ºPº position, start the engine. Be
sure to keep the brake pedal depressed. 2. Shift into the º3º, º2º, ºLº or ºRº position.
3. Release the parking brake and brake pedal and slowly pull
or back away from the wheel blocks. Stop and apply your
brakes.
4. Have someone retrieve the blocks.

CHASSIS
360It is normal for the brake fluid level to go down slightly as the
brake pads wear. So be sure to keep the reservoir filled.
If the reservoir needs frequent refilling, it may indicate a
serious mechanical problem.
If the level is low, add FMVSS No.116 DOT 3 or SAE
J1703 brake fluid to the brake reservoir.
Remove and replace the reservoir cover by hand. Add brake
fluid up to the ºMAXº line.
Use only newly opened brake fluid. Once opened, brake fluid
absorbs moisture from the air, and excess moisture can cause
a dangerous loss of braking efficiency.
CAUTION
Take care when filling the reservoir because brake fluid can
harm your hands or eyes and damage painted surfaces. If
fluid gets in your hands or eyes, flush them with clean water.
NOTICE

If you spill some of the fluid, be sure to wipe it off to
prevent it from damaging the parts or paintwork.
 For vehicles with traction control system only:Idle
the engine while pouring brake fluid into the reservoir.