1999 LEXUS SC300 low

COMFORT ADJUSTMENT
167
CAUTION

Always make sure the shoulder belt is positioned across the
center of child's shoulder. The belt should be kept away
from child's neck, but not falling off child's shoulder.
Failure to do so could reduce the amount of pr otection in an
accident and cause serious injuries in a collision.

High±positioned lap belts and loose±fitting belts both could
cause serious injuries due to sliding under the lap belt
during a collision or other unintended result. Keep the lap
belt positioned as low on hip as possible.

For child's safety, do not place the shoulder belt under
child's arm.

After inserting the tab, make sure the tab and buckle are
locked and that the lap and shoulder portions of the belt are
not twisted.

Do not insert coins, clips, etc. in the buckle as this may
prevent you from properly latching the tab and buckle.

If the seat belt does not function normally, immediately
contact your Lexus dealer. Do not use the seat until the seat
belt is fixed. It cannot protect your child from injury.

COMFORT ADJUSTMENT
168
2. To remove the child restraint system, press the
buckle±release button and allow the belt to retract.DRIVING POSITION MEMORYSYSTEM
The micro computer can memorize the position of the driver's
seat, the positions of the tilt and telescopic steering, and
outside rear view mirrors. Two different driving position
profiles can be entered into the computer's memory.
This can only be done when the ignition key is in the ºONº
position, and the selector lever is in the ºPº position.
Setting a driving position

SECTION 1 ± 7
172
INSTRUMENTS AND CONTROLS
Theft deterrent
Theft deterrent system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
172
Theft prevention labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
175
THEFT DETERRENT SYSTEM
To deter theft of the vehicle, this system is designed to give
an alarm if any of the doors, trunk or hood is forcibly
unlocked or the battery terminal is disconnected and then
reconnected while the vehicle is locked.
The alarm blows the horn intermittently and flashes the
headlights, tail lights and other exterior lights.

THEFT DETERRENT
173
Setting the system
1. Turn the ignition key to the ºLOCKº position and
remove it.
The indicator light flashes by means of the engine
immobiliser system.
2. Close and lock all the doors, trunk and hood using an
ignition key or wireless remote control.If you lock them with wireless remote control, the turn signals
flash once.
The flashing indicator light changes to stay on when all the
doors, trunk and hood are closed and locked.
3. After 30 seconds, the indicator starts flashing and the
system is set.
Cancelling the system
When you unlock any door or trunk using an ignition key
or wireless remote control, the system is cancelled.
If you unlock any door or trunk with wireless remote control,
the turn signals flash twice.
Activating the system
The alarm sounds for 60 seconds if any of the following are
operated:


Unlocking any door or trunk without using an ignition key
or wireless remote control.

Opening the hood forcibly.

Reconnecting the battery.
If any door is unlocked and the ignition key is not in the
ignition switch during the alarm sounding, its door is
automatically locked.

THEFT DETERRENT
174To stop the alarm: Use either of the following methods.


Unlock the door or trunk using an ignition key or wireless
remote control.

Turn the ignition switch on.
Testing the system
1. Open all the windows.
2. Set the system as described above.
The front doors should be locked with the ignition key or
wireless remote control. Be sure to wait until the indicator
light starts flashing.
3. Unlock one of the doors from the inside.
The system should activate the alarm.
4. Unlock any of the doors with a key or the wireless
remote control to cancel the system.
5. Repeat this operation for the other doors and hood.
When testing the hood, also check that the system is activated
when the battery terminal is disconnected and then
reconnected.
If the system does not work properly, have it checked by your
Lexus dealer.
NOTICE
Disconnecting the battery may result in the erasure of
information you have set in the computer memory. After
reconnecting the battery, check that the memorized data
has been retained. If it has been erased, input it into the
computer once more.

AIR CONDITIONING AND AUDIO
180The automatic air conditioning automatically maintains the
set temperature.
This air conditioning features automatic fan speed and air
flow
control which automatically selects the most suitable fan
speed and air flow to control the temperature. The ignition
key must be in the ºONº position.
You may use manual control to override the automatic
settings.
You can adjust the brightness of the display. See ºInstrument
panel light controlº on page 64 for details.

AIR CONDITIONING AND AUDIO
181
(a) Climate control
SETTING OPERATION ± automatic control
1. Push the ºAUTOº knob.
Air flow quantity, switching of the diffusers, on±off of the air
conditioning, and switching of the air intake between
RECIRCULATED AIR and OUTSIDE AIR are
automatically adjusted. The operation status is shown by
each indicator.
When one of the manual control buttons is depressed while
operating in automatic mode, the operation corresponding to
the button depressed is set. Other conditions continue to be
adjusted automatically. 2. Turn the ºTEMPº knob until the desired temperature
is displayed.
The ºTEMPº knob is used to set the desired passenger
compartment temperature. The temperature of air delivered
to the passenger compartment will be controlled
automatically according to the setting. The figures on the
panel indicate degrees Fahrenheit.
SETTING OPERATION ± manual control
If manual air flow selection is desired ±
The outlets from which air is delivered can be selected
manually by pushing either side of the air flow control
(MODE) button. The mode appears on the display.
The function of each mode is as follows:
PANEL mode ± Directs air flow at face level.
BI±LEVEL mode ± Directs air flow at face level and
at floor level for both front and rear. Except in ventilation, the
air to the floor is slightly warmer than air to the face.
FLOOR mode ± Directs air flow mostly at floor level
for both front and rear.
FLOOR/WINDSHIELD mode ± Directs air flow to
the windshield and front side windows as well as floor level
for both front and rear.
FRONT WINDSHIELD mode ± Directs air flow
mostly to the windshield and front side windows.
When this mode is selected while operating in automatic
mode, the air conditioning is set to operate and the OUTSIDE

AIR CONDITIONING AND AUDIO
183
set to OUTSIDE AIR mode. If recirculated air is used during
heating, the windows will fog up more easily.
If manual on±off of the air conditioning is desired ±
Push the
(A/C) button to turn the air conditioning on
and push it again to turn the air conditioning off.
The air conditioning does not work if the outside temperature
is lowered down to around 0C (32F).
If the system is used for ventilation, heating in dry weather or
removing frost or exterior fog on the windshield, turn the air
conditioning off once it is no longer required. This will
improve fuel economy. The air conditioning can be used for
year±round automatic temperature control including cooling
and dehumidifying operation. If the air conditioning compressor does not operate, the
indicator of the
(A/C) button will blink. If the indicator
of the (A/C) button blinks even when the (A/C)
button is pushed again, have the compressor checked by your
nearest Lexus dealer.
(b) Windshield defogging and defrosting
See º(a) Climate controlº for details on each button.
To remove interior fog on the windshield ±
Push the
(WINDSHIELD) button.
To remove frost or exterior fog on the windshield ±
1. Place the temperature control knob at the maximum
temperature.
2. Push the
(WINDSHIELD) button.
3. Push the right side of the fan speed control
(FAN)
button to set the fan speed at the maximum speed.