1999 Lexus ES300 ECO mode

GAUGES, METERS AND SERVICE REMINDER INDICATORS
56

ºODO/TRIPº knob
This meter displays the odometer and two trip
meters. To change the mode indication, push the
ºODO/TRIPº knob briefly. Each time you push the
knob,
the mode changes in order from the odometer
to trip meter A to trip meter B, then back to the
odometer, etc.
The odometer records the total distance the vehicle
has been driven. The twin trip meter records two
different distances independently.
For example, you can use one meter to calculate the fuel
economy and the other to measure the distance on each
trip.
To set the A trip meter to zero, display the A meter
reading, push the knob and hold it. The same
applies for the B trip meter.
The data of trip meters will be cancelled if the electrical
power source is disconnected.
SERVICE REMINDER
INDICATORS AND WARNING BUZZERS
IF THIS INDICATOR
OR BUZZER COMES
ON ... DO THIS.

INTERIOR EQUIPMENT
84Do not use the HomeLink
 universal transmitter with
any garage door opener that lacks the safety stop and
reverse feature as required by Federal Safety
Standards. This includes any garage door opener
model manufactured before April 1, 1982.
CAUTION
When programming or operating the garage door
opener, make sure there is no one around the moving
door. It is dangerous if someone is caught.
(b) Operating the garage door opener
Push the appropriate button to activate the garage door
opener. The indicator light comes on. The garage door
opener continues to send the signal for up to 20 seconds
as long as the button is pushed.
(c) Erasing the garage door opener memory
Push and hold down the 2 outside buttons for about 20
seconds until the indicator light flashes. All memorized
data will be erased. FCC ID: CB2V94800
CANADA: 1763 102 264
This device complies with FCC Rules part 15.
Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference that may be received,
including interference that may cause undesired
operation. WARNING: This transmitter has
been tested and complies with FCC and
DOC/MDC rules. Changes or modifications
not expressly approved by the partly
responsible for compliance could void the
user's authority to operate the device.

COMFORT ADJUSTMENT
188
16E034±1

1Bolt 2Anchor bracket 3Spacer
3. Insert a 15 mm (0.6 in.) spacer, and tighten down the
anchor bracket for your child restraint system with a bolt.
Torque the bolt to 16.5 ± 24.7 N´m (1.68 ±2.52 kgf´m,
12.2 ± 18.2 ft´lbf.).
To comply with Canadian Motor Vehicle Safety
Standards, this model sold in Canada is provided with a
bracket set in the glovebox, designed for use with any of
the 3 anchor locations shown in the illustration.
DRIVING POSITION MEMORY SYSTEM
The micro computer can memorize the position of the
driver's seat. Two different driving position profiles can
be entered into the computer's memory.
Recording a driving position in the computer's memory
can only be done when the ignition key is in the ºONº
position and the selector lever is in the ºPº position.
Setting a driving position
16E047

AIR CONDITIONING AND AUDIO
209
The air intake control button is used to switch the air
intake between the OUTSIDE AIR mode and
RECIRCULATED AIR mode.
With the button in the OUTSIDE AIR mode, the
OUTSIDE AIR mode indicator light will come on and the
system will take fresh outside air into the vehicle.
If quick circulation of cooled air is desired, push the air
intake control button for RECIRCULATED AIR. The
RECIRCULATED AIR mode indicator light will come on.
For normal use, it is best to keep the air intake control
button set to OUTSIDE AIR mode. If recirculated air is
used
during heating, the windows will fog up more easily.
If the engine coolant temperature becomes extremely
high, the RECIRCULATED AIR mode is automatically
selected. This is not a malfunction. When the engine
coolant temperature is lowered, the previous mode
resumes.
If manual on±off of the air conditioning is desired ±
Push the ºA/Cº button to turn the air conditioning on and
push it again to turn the air conditioning off.
The air conditioning does not work if the outside
temperature is lowered down to around 0 C (32F).
If the system is used for ventilation, heating in dry
weather or removing frost or exterior fog on the
windshield, turn the air conditioning off once it is no
longer required. This will improve fuel economy. The air
conditioning can be used for year±round automatic temperature
control including cooling and dehumidifying
operation.
If the air conditioning compressor does not operate, the
indicator of the ºA/Cº button will blink. If the indicator of
the ºA/Cº button blinks even when the ºA/Cº button is
pushed again, have the compressor checked by your
nearest Lexus dealer.
Displaying the outside temperature ±
When you push the ºOUTSIDE TEMPº knob, the
temperature display shows the outside temperature. To
return to the display of the current set temperature, push
the knob again. The temperature display ranges from
±30 C (±22 F) up to 50C (122F).

AIR CONDITIONING AND AUDIO
212
(c) Operating tips
Make sure the air inlet grilles in front of the windshield
are not blocked by leaves or other obstructions.
 If air flow control is not satisfactory, check the
dashboard vents. (See ºSide ventsº.)
 To help cool down the interior after parking in the hot
sun, drive for the first few minutes with the windows
open. After the excess heat has blown away, close
the windows.
 When driving on dusty roads, close all windows. If
dust thrown up by the vehicle is still drawn into the
vehicle after closing the windows, it is recommended
that the air intake control button be left to the
OUTSIDE AIR mode and the fan speed control button
be pressed to anywhere except the ºOFFº button.
 If following another vehicle on a dusty road, or driving
in windy and dusty conditions, it is recommended that
the air intake control button be temporarily pressed in
to the RECIRCULATED AIR mode, which will close
off the outside passage and prevent outside air and
dust from entering the vehicle interior.

AIR CONDITIONING AND AUDIO
218In the ºTAPEº or ºCDº mode, the applicable
functions
are shown in the lowest part of the display.
Push the switch just below to turn on each function.
(b) Tone and balance
How good an audio program sounds to you is largely
determined by the mix of the treble, mid±range, and
bass levels. In fact, different kinds of music and vocal
programs usually sound better with different mixes of
treble, mid±range, and bass.
A good balance of the left and right stereo channels and
of the front and rear sound levels is also important.
Keep in mind that if you are listening to a stereo
recording or broadcast, changing the right/left balance
will increase the volume of one group of sounds while
decreasing the volume of another.
20E015±1

AIR CONDITIONING AND AUDIO
227
If a cassette is already in the slot, push the ºTAPEº
button.
Dolby Noise Reduction* feature:
If you are listening to
a tape that was recorded with Dolby* B or C Noise
Reduction, push the button by the double±D symbol until
the appropriate symbol appears on the display.
The Dolby B NR mode reduces tape noise by about 10
dB. The Dolby C NR mode reduces tape noise by
another 10 dB or about 20 dB total. For best sound
reproduction, select the same NR mode that was used
to record the tape.
To play a tape recorded without Dolby NR, push the
button until the symbol disappears from the display.
* Dolby noise reduction manufactured under license from Dolby
Laboratories Licensing Corporation. ºDOLBYº and the
double±D symbol
are trademarks of Dolby Laboratories
Licensing Corporation.
(b) Manual program selection
20E024±1

STARTING AND DRIVING
280You can turn off the traction control system by
pushing the ºTRAC OFFº switch. The ºTRAC OFFº
indicator/warning light will then come on. Pushing
the ºTRAC OFFº switch a second time turns the
system back on and extinguishes the ºTRAC OFFº
indicator/warning light.
You may hear a sound in the engine compartment for a
few seconds when the engine is started or just after the
vehicle is started. This means that the traction control
system is in the self
±check mode, and does not indicate
malfunction.
When the traction control system is operating, you may
feel vibration or noise of your vehicle, caused by
operation of the brakes. This indicates the system is
functioning properly.
When getting the vehicle out of mud or new snow, etc.
the traction control system will help operate to prevent
the wheels from spinning.