1999 LAND ROVER DISCOVERY warning

TORQUE WRENCH SETTINGS
06-11
Transfer box - LT230SE
† New nut must be fitted
* New Patchlok nut must be fitted
+ Apply sealant, Part No. STC 50552 to threads
TORQUE DESCRIPTION METRIC IMPERIAL
High/low selector cable 30 Nm (22 lbf.ft)
Bottom cover plate bolts + 25 Nm (18 lbf.ft)
Transfer box to gearbox bolts - Petrol and diesel + 45 Nm (33 lbf.ft)
Rear cover plate stud nut/bolts + 25 Nm (18 lbf.ft)
Differential lock warning lamp switch locknut - Up to 03 MY 11 Nm (8 lbf.ft)
Differential lock warning lamp switches - 03 MY onwards + 25 Nm (18 lbf.ft)
Drive flange nut 148 Nm (109 lbf.ft)
Output shaft housing bolts + 45 Nm (33 lbf.ft)
Oil temperature sensor - If fitted + 25 Nm (18 lbf.ft)
Inhibitor switch to transfer box 26 Nm (19 lbf.ft)
Intermediate shaft nut † 88 Nm (65 lbf.ft)
Intermediate shaft retaining plate bolt + 25 Nm (18 lbf.ft)
Differential bearing retaining nut * 72 Nm (53 lbf.ft)
Output flange nut 162 Nm (119 lbf.ft)
High/Low selector housing bolts + 25 Nm (18 lbf.ft)
Bearing housing/cover bolts + 25 Nm (18 lbf.ft)
Blanking plug + 25 Nm (18 lbf.ft)
High/Low selector warning lamp switch 25 Nm (18 lbf.ft)
Differential lock selector housing bolts + 25 Nm (18 lbf.ft)
Neutral sensor 25 Nm (18 lbf.ft)
Interlock solenoid bolts - Up to 03 Model Year 10 Nm (7 lbf.ft)

LIFTING AND TOWING
08-1
LIFTING AND TOWING
LIFTING
The following instructions must be carried out before
raising the vehicle off the ground.
lUse a solid level ground surface.
lApply hand brake.
lSelect 'P' (Automatic gearbox) or 1st gear
(Manual gearbox) in main gearbox.
lSelect Low range in transfer gearbox.
To avoid damage occurring to the under body
components of the vehicle the following jacking
procedures must be adhered to.
DO NOT POSITION JACKS OR AXLE STANDS
UNDER THE FOLLOWING COMPONENTS:
lBody structure
lBumpers
lFuel lines
lBrake lines
lFront radius arms
lPanhard rod
lSteering linkage
lRear trailing arms
lFuel tank
lEngine sump
lGearbox bell housing
Vehicle jack
The jack provided with the vehicle is only intended for
use in an emergency, for changing a tyre. DO NOT
use the jack for any other purpose. Refer to Owner's
Handbook for vehicle jack location points and
procedure. Never work under a vehicle supported
solely by the vehicle jack.
Hydraulic jack
A hydraulic jack with a minimum 1500 kg, 3,300 lbs
load capacity must be used. Do not commence
work on the underside of the vehicle until
suitable axle stands have been positioned under
the axle.
WARNING: Always chock the wheels when
jacking. The hand brake acts on the
transmission, not the rear wheels, and may be
ineffective when the wheels are off the ground.Raising and supporting the vehicle
Position cup of hydraulic arm under differential
casing (1).The differential casing is not central to
the axle. Care should be taken when raising the
front road wheels off the ground as the rear axle
has less sway stiffness.
Raise vehicle to enable an axle stand to be installed
under left hand axle tube (2).
Position an axle stand under right hand axle tube (4).
Carefully lower jack until vehicle sits securely on both
axle stands, remove jack.
Alternatively, the axle stands can be positioned
under the chassis longitudinals at the front and/or
rear of the vehicle.

LIFTING AND TOWING
08-2
Before commencing work on underside of vehicle re-
check security of vehicle on stands.
WARNING: Always chock the wheels when
jacking. The hand brake acts on the the
transmission, not the rear wheels, and may be
ineffective when the wheels are off the ground.
Reverse procedure when removing vehicle from
stands.
Hydraulic ramps
Use only a 'drive on' type ramp which supports a
vehicle by it's own road wheels. If a 'wheel free'
condition is required, use a 'drive on' ramp
incorporating a 'wheel free' system that supports
under axle casings. Alternatively, place vehicle on a
firm, flat floor and support on axle stands.
TOWING
Towing
The vehicle has permanent four wheel drive. The
following towing instructions must be adhered
to:
Towing on 4 wheels with driver
Turn ignition key to position '1' to release steering
lock.
Select neutral in main gearbox and transfer gearbox.
Secure tow rope, chain or cable to towing eye.
Release the handbrake.
The brake servo and power assisted steering
system will not be functional without the engine
running. Greater pedal pressure will be required
to apply the brakes, the steering system will
require greater effort to turn the front road
wheels. The vehicle tow connection should be
used only in normal road conditions, 'snatch'
recovery should be avoided.
Suspended tow
To prevent vehicle damage, front or rear
propeller shaft MUST BE removed, dependent
upon which axle is being trailed.
Mark propeller shaft drive flanges at transfer box and
axles with identification lines to enable the propeller
shaft to be refitted in its original position.

CAPACITIES, FLUIDS, LUBRICANTS AND SEALANTS
09-2
Fluids
Anti-freeze
Use Havoline Extended Life Coolant (XLC), or any
ethylene glycol based anti-freeze (containing no
methanol) with only Organic Acid Technology (OAT)
corrosion inhibitors, to protect the cooling system
CAUTION: No other anti-freeze should be used
with Havoline Extended Life Coolant.
The cooling system should be drained, flushed and
refilled with the correct amount of anti-freeze solution
at the intervals given on the Service Maintenance
Check Sheet.
After filling with anti-freeze solution, attach a warning
label to a prominent position on the vehicle stating
the type of anti-freeze contained in the cooling
system to ensure that the correct type is used for
topping-up.
Brake/Clutch fluid
Use only DOT 4 brake fluid.
PAS fluid
Use Texaco cold climate power assisted steering
fluid PSF 14315.
ACE fluid
Where ambient temperature falls below -20° C (-4°
F), use only Texaco cold climate power assisted
steering fluid PSF 14315. Where ambient
temperature remains above -20° C (-4° F), use either
Texaco cold climate power assisted steering fluid ,
Dexron 11 or Dexron 111 non-synthetic fluid.
Air conditioning
Use only refrigerant R134a.
Refrigerant oil
Use only Nippon Denso ND-oil 8.
Refrigerant oil absorbs water and must not be stored
for long periods. Do not pour unused oil back into the
container.
NOTE: The total quantity of refrigerant oil in the
system is 180 ml.
CAUTION: Do not use any other type of
refrigerant oil.
Anti-Freeze Concentration
The overall anti-freeze concentration should not fall,
by volume, below 50% to ensure that the anti-
corrosion properties of the coolant are maintained.
Anti-freeze concentrations greater than 60% are not
recommended as cooling efficiency will be impaired.
The following recommended quantities of anti-freeze
will provide frost protection to -48°C (-53°F):
Engine - TD5
Engine - V8
Concentration 50%
Amount of Anti-freeze 4 litres
Concentration 50%
Amount of Anti-freeze 6.5 litres
13.5 pts (US)

CAPACITIES, FLUIDS, LUBRICANTS AND SEALANTS
09-5
Manual
Gearbox -
R380Gate plate bolts STC 50552
Manual
Gearbox -
R380Gear case to
extension housingSTC 4404
Manual
Gearbox -
R380Extension housing
boltsSTC 50552
Manual
Gearbox -
R380Gear change lever
yoke Allen screwSTC 50552
Manual
Gearbox -
R380Gear case to centre
plateSTC 4404
Manual
Gearbox -
R380Detent plugs STC 50552
Manual
Gearbox -
R380Bias spring
adjustment plate
boltsSTC 50552
Transfer Box -
LT230SEBottom cover plate STC 4600
Transfer Box -
LT230SEBottom cover plate
boltsSTC 50552
Transfer Box -
LT230SEFront output
housing core plugSTC 3811
Transfer Box -
LT230SETransfer box to
gear case bolts -
Petrol and Diesel
enginesSTC 50552
Transfer Box -
LT230SETransfer box to
gear case studs -
Petrol and Diesel
enginesSTC 50552
Transfer Box -
LT230SERear cover STC 4600
Transfer Box -
LT230SEDifferential warning
lamp switch(es)STC 50552
Transfer Box -
LT230SEHigh/Low selector
warning lamp
switchSTC 50552
Transfer Box -
LT230SERear output shaft
housingSTC 4600
Transfer Box -
LT230SERear output shaft
housing boltsSTC 50552
Transfer Box -
LT230SEHigh/Low selector
fork set screwSTC 50552
Transfer Box -
LT230SEInterlock solenoid
selector cover - Up
to 03 MYSTC 4600
Transfer Box -
LT230SEInterlock solenoid
circlip - 03 MY
onwardsSTC 50551
Transfer Box -
LT230SENeutral sensor STC 50552
Transfer Box -
LT230SEIntermediate shaft
retaining plate boltSTC 50552Transfer Box -
LT230SESide cover STC 4600
Transfer Box -
LT230SESide cover bolts STC 50552
Transfer Box -
LT230SEDifferential lock
selector shaft
detent plugSTC 50552
Transfer Box -
LT230SEDifferential lock
selector housing
boltsSTC 50552
Transfer Box -
LT230SEFront output shaft
housingSTC 4600
Transfer Box -
LT230SEFront output shaft
housing boltsSTC 50552
Transfer Box -
LT230SEHigh/Low selector
shaft detent plugSTC 50552
Transfer Box -
LT230SEInput gear bearing
housingSTC 4600
Transfer Box -
LT230SERear cover stud nut
and boltSTC 50552
Transfer Box -
LT230SEHigh/Low cross
shaft housingSTC 4600
Transfer Box -
LT230SEHigh/Low cross
shaft housing boltsSTC 50552
Automatic
gearbox -
ZFHP22-24Torque converter
housing to engine
boltsSTC 50553
Rear Axle and
Final DriveDifferential cover to
casingSTC 3811
Rear Axle and
Final DriveDifferential cover to
casing boltsSTC 50552
Front axle Differential cover to
casingSTC 3811
Front axle Differential cover to
casing boltsSTC 50552
Front
suspensionDrive shaft to hub STC 50554
Rear
suspensionDrive shaft to hub STC 50554
Rear
suspensionSLS air compressor
boltsSTC 50552

MAINTENANCE
PROCEDURES 10-5
Lamps, horns and warning indicators
Check
1.Switch on side, head and tail lamps and check
operation.
2.Check headlamp levelling operation.
3.Check turn signals and hazard warning lamps
for correct operation.
4.Press brake pedal and check operation of
brake lamps.
5.Check all exterior lamp lenses for clarity and
condition. Pay particular attention to headlamp
lenses for signs of stone chips or damage.
6.Check horn for loud, clear sound.
7.Switch on headlamps (with ignition switch at 'O'
position) and check light reminder warning
operates when door is opened.
8.Check operation of interior courtesy lights.
9.Check operation of all instrument pack warning
and indicator lights.
Wipers and washers
Check
1. Operate screen washer and switch on wipers.
Ensure washer jets are correctly aimed and
check for smooth, smear free operation of
wiper blades across screen at all speeds
including intermittent.
2.Repeat operation for rear screen washers/
wipers.
3.Check all wiper blades for condition and signs
of splits or damage.
4.Check security of wiper arms.

MAINTENANCE
10-14 PROCEDURES
Intercooler - diesel engine
Remove
1.Remove intercooler.

+ ENGINE MANAGEMENT SYSTEM -
Td5, REPAIRS, Intercooler.
Flush
1.Flush intercooler element using Flushing
Solvent Part No. STC 9713, following the
manufacturer's instructions.
2.Thoroughly dry intercooler ensuring that no
trace of solvent remains in the element.
3.Refit intercooler on completion.

+ ENGINE MANAGEMENT SYSTEM -
Td5, REPAIRS, Intercooler.
Engine oil - V8 engine
WARNING: Avoid excessive skin contact with
used engine oil. Used engine oil contains
potentially harmful contaminants which may
cause skin cancer or other serious skin
disorders.
Replace
1.Position suitable container beneath sump.
2.Clean area around oil drain plug.
3.Remove oil drain plug, discard sealing washer.
4.Allow oil to drain.
5.Fit new sealing washer to oil drain plug.
6.Fit engine drain plug and tighten to 33 Nm (24
lbf.ft).
7.Fill engine with recommended grade of oil to
correct mark on dipstick.

+ CAPACITIES, FLUIDS,
LUBRICANTS AND SEALANTS,
Lubrication.

MAINTENANCE
PROCEDURES 10-15
Engine oil - diesel engine
WARNING: Avoid excessive skin contact with
used engine oil. Used engine oil contains
potentially harmful contaminants which may
cause skin cancer or other serious skin
disorders.
Replace
1.Release fixings, remove underbelly panel.
2.Position suitable container beneath sump.
3.Clean area around drain plug.
4.Remove oil drain plug, discard sealing washer.
5.Allow oil to drain.
6.Fit new sealing washer to oil drain plug.
7.Fit engine drain plug and tighten to 23 Nm (17
lbf.ft).
8.Fill engine with recommended grade of oil to
correct mark on dipstick.

+ CAPACITIES, FLUIDS,
LUBRICANTS AND SEALANTS,
Lubrication.
9.Fit front underbelly panel, secure fixings.
Centrifuge rotor – diesel engine
Replace
1.Replace centrifuge rotor.

+ ENGINE - Td5, REPAIRS, Rotor -
centrifuge.