Page 553 of 667

77PANEL REPAIRS
28
SEALING AND CORROSION PROTECTION WATER LEAKS
Sealing charts in this section show those areas of the
bodyshell most likely to be affected by accident
damage and water leaks, and which could therefore
require re-treatment in repair. They do not show those
joint areas which only apply to factory assembly
operations and which are unlikely to be disturbed in
service (e.g. centre tunnel), or where the damage
would be so severe that the entire bodyshell would
normally be written off.
When water leakage occurs, always adopt a logical
approach to the problem using a combination of skill,
experience and intuition. Do not attempt to reach a
conclusion based only on visual evidence, such as
assuming that a leak emanates from the windscreen
because the footwell is wet. It will often be found that
the source of the leak is elsewhere. The correct
procedure will increase the chance of locating a leak,
however obscure it may seem.
Tools and Equipment
The following tools and equipment are recommended
for detection and rectification of water leaks:
1. Garden sprayer (hand-operated).
2. Wet/dry vacuum cleaner.
3. Dry absorbent cloths.
4. Battery torch.
5. Small mirror.
6. Weatherstrip locating tool.
7. Trim panel remover.
8. Small wooden or plastic wedges.
9. Dry compressed air supply.
10. Hot air blower.
11. Sealer applicators.
12. Ultrasonic leak detector.
During leak detection, the vehicle should be
considered in three basic sections:
The front interior space,
The rear passenger space (where
applicable), and
The rear loadspace or boot.Testing
From the information supplied by the customer it
should be possible for the bodyshop operator to locate
the starting point from which the leak may be
detected. After the area of the leak has been
identified, find the actual point of entry into the vehicle.
A simple and effective means initially is an ordinary
garden spray with provision for pressure and jet
adjustment. This will allow water to be directed in a jet
or turned into a fine spray. Use a mirror and a
battery-powered torch (NOT a mains voltage
inspection lamp) to see into dark corners.
The sequence of testing is particularly important. Start
at the lowest point and work slowly upwards, to avoid
testing in one area while masking the leak in another.
For example, if testing started at the level of the
windscreen, any water cascading into the plenum
chamber could leak through a bulkhead grommet and
into the footwells. Even at this point it could still be
wrongly assumed that the windscreen seal was at
fault.
Another important part of identifying a water leak is by
visual examination of door aperture seals, grommets
and weatherstrips for damage, deterioration or
misalignment, together with the fit of the door itself
against the seals.
Sealing
When the point of the leak has been detected,
proceed to rectify it using the following procedure:
1. Renew all door aperture seals and weatherstrips
which have suffered damage, misalignment or
deterioration.
2. Check all body seals to ensure that they are
correctly located on their mounting flanges/faces
using a locating tool if necessary.
3. Dry out body seams to be treated using
compressed air and/or a hot air blower as
necessary.
4. Apply sealant on the outside of the joint
wherever possible to ensure the exclusion of
water.
5. When rectifying leaks between a screen glass
and its weatherstrip (or in the case of direct
glazing, between the glass and bodywork), avoid
removing the glass if possible. Apply the
approved material either at the glass to
weatherstrip or glass to body.
ProCarManuals.com
Page 568 of 667

PANEL REPAIRS
3
REPAIR WHEEL ARCH - FRONT
Remove
The procedure to change the Inner Front Wheelarch is
the same as for the Wing Upper, except for removal of
the ABS sensors and shield, if fitted.
BULKHEAD ASSEMBLY
Remove
1.Disconnect both battery leads, negative lead
first.
2.Remove front lower wing.See this Section.
3.Remove RH and LH front upper wing.See this
Section.
4.Remove headlamp mounting panels.See this
Section.
5.Remove screen aperture.See this Section.
6.Remove both front doors.
7.Remove lower fascia panel.See CHASSIS
AND BODY, Repair.
8. Models with A/C:Remove relevant A/C pipes.
9.Remove front grille.
10.Drain cooling system.See COOLING
SYSTEM, Adjustment.
11.Remove radiator and intercooler.
12. Models with A/C:Remove condensor.
13.Remove air cleaner assembly.
14.Remove heater unit.See HEATING AND
VENTILATION, Repair.
15.Remove brake servo assembly.
16.Remove heater ducts.
17.Remove both front seats.
18.Remove front carpets.
19.Release all relevant harnesses and position
aside.
20.Remove facia support bracket.
Refit
21.Prepare and clean panel joint faces. Ensure all
necessary grommets and sealant is applied to
new bulkhead.
22.Reverse removal procedure.
23.Bleed brake system.See BRAKES,
Adjustment.
24.Align headlamps.See ELECTRICAL,
Adjustment.
25.Water test after refitting.
ProCarManuals.com
Page 635 of 667

86ELECTRICAL
26
DESCRIPTION AND OPERATION PASSENGER COMPARTMENT FUSE BOX
FROM 02MY
The increase in electrical systems on Defender 02MY vehicles has necessitated an increase in the number of
fuses required.
The passenger compartment fuse box now contains three rows of fuses instead of the previous two rows and
relays to control the CDL system, heated front screen, headlamps, anti-theft alarm ECU and seat heaters and
window lift system.
1.Fuse 8 - Anti-theft alarm ECU/BBUS (10A)
2.Fuse 9 - Front wiper motor and washer pump
(15A)
3.Fuse 10 - Rear wiper relay (10A)
4.Fuse 11 - ABS ECU (10A)
5.Fuse 12 - Engine Control Module (10A)
6.Fuse 13 - Brake pedal switch (10A)
7.Fuse 14 - Reverse lamp switch/Glowplugs (10A)
8.Fuse 15 - Miscellaneous relay control. See
Electrical Library (5A)
9.Fuse 16 - Cigar lighter/Heater blower (20A)
10.Fuse 17 - Radio (5A)
11.Fuse 18 - LH side lamps/trailer pick up (10A)
12.Fuse 19 - RH side lamps/trailer pick up (10A)
13.Fuse 20 - Headlamp levelling/Illumination (10A)
14.Fuse 21 - Direction indicators (10A)
15.Fuse 22 - RH headlamp dip beam (10A)
16.Fuse 23 - LH headlamp dip beam (10A)
17.Fuse 24 - RH headlamp main beam (10A)
18.Fuse 25 - LH headlamp main beam (10A)19.Fuse 26 - Rear fog lamp ECU (10A)
20.Fuse 27 - Alarm relay (10A)
21.Fuse 28 - Air conditioning blower relay (30A)
22.Fuse 29 - Air conditioning compressor
relay/cooling fan relay (20A)
23.Fuse 30 - Interior lamps/radio/alarm
LED/clock/diagnostic socket/tachometer (South
African vehicles only) (5A)
24.Fuse 31 - Hazard warning lamps (15A)
25.Fuse 32 - Heated rear window (20A)
26.Fuse 33 - Seat heat relay (20A)
27.Fuse 34 - RH window lift switch (20A)
28.Fuse 35 - LH window lift switch (20A)
29.Fuse 36 - Heated front screen (30A)
30.Relay - Heated Front Screen
31.Relay - Starter motor
32.Relay - Heated Rear Window
33.Relay - Headlamps
34.Relay - Anti-theft alarm
35.Relay - Seat heat/window lift
ProCarManuals.com
Page 636 of 667
ELECTRICAL
27
DESCRIPTION AND OPERATION UNDER SEAT FUSE BOX
FROM 02MY
1.A/C Relay (if fitted)
2.A/C relay (if fitted)
3.Glow plug relay
4.Main relay
5.Fuel pump relay
6.ABS Return pump relay
7.Fuse 7 - Central Door Locking (CDL) and BBUS
(20A)
8.Fuse 6 - Anti-theft alarm ECU (15A)
9.Fuse 5 - Main relay (30A)10.Fuse 4 - Fuel pump relay (20A)
11.Fuse 3 - Horn/HRW relay (20A)
12.Fuse 2 - Accessory socket (20A)
13.Fuse 1 - ABS ECU (30A)
14.Fusible link 6 - Lights (30A)
15.Fusible link 5 - Ignition switch/Starter relay (60A)
16.Fusible link 4 - ABS Pump relay (30A)
17.Fusible link 3 - Window lift/Seat heat relay (60A)
18.Fusible link 2 - Air conditioning (60A)
19.Fusible link 1 - Glow plugs/Heated front screen
(100A)
ProCarManuals.com