1999 LAND ROVER DEFENDER wheel bolts

64REAR SUSPENSION
2
REPAIR 25.If end float is present refer to table for correct
spacer and change spacer as necessary.
26.When no end float is evident, remove the dial
gauge and mounting bracket.
27.Stake the hub nut.
28.Clean hub and axle shaft faces.
29.Fit new driving member gasket.
30.Position driving member to hub and tighten new
bolts to65 Nm (48 lbf.ft).
31.Fit original shim(s) to drive shaft and secure with
circlip.
32.Position caliper to hub, fit bolts and tighten to82
Nm (61 lbf.ft).
33.Fit road wheel, remove axle stands and tighten
road wheel nuts to130 Nm (96 lbf.ft).
34.Operate brake pedal to locate brake pads before
driving vehicle.
35.Check and top up brake fluid.
ProCarManuals.com

BRAKES
3
REPAIR SENSORS - ABS - REAR WHEELS
Service repair no - 70.65.31
Remove
1.Raise vehicle on a 2 post ramp.
2.Remove both rear wheels.
3.Remove 3 bolts securing each brake disc
backplate to hub assemblies.
4.Remove both back plates.
5.Remove 2 cable ties securing sensor harness to
outer ends of axle.
6.Carefully prise both sensors from hub
assemblies.
7.Release 4 clips securing sensor harness to axle.
8.Release cable tie securing harness to
differential.
9.Release 3 cable ties securing harness to chassis
longitudinal.
10.Disconnect sensor multiplug.
11.Remove harness and sensor assembly.
Refit
12.Position harness and sensor assembly to vehicle
and connect multiplug.
13.Apply grease to both sensors.
14.Carefully fit both sensors to hub assemblies.
15.Secure harness to axle and differential with
cable ties.
16.Secure harness to axle with clips.
17.Secure harness to chassis with cable ties.
18.Fit both back plates to hub assemblies and
secure with bolts.
19.Fit rear wheels and tighten to130 Nm (95 lbf.ft)
.
20.Lower vehicle.
ProCarManuals.com

BRAKES
7
REPAIR Refit
11.Position modulator to mounting bracket and
connect multiplug.
12.Fit modulator to mounting bracket and tighten
nuts to9 Nm (7 lbf.ft).
13.Connect 2 multiplugs to rear of modulator.
14.Remove plugs from brake pipes and modulator.
15.Clean brake pipe unions.
16.Connect brake pipe unions to modulator
ensuring pipes are connected to their correct
ports.
17.Tighten all unions to14 Nm (10 lbf.ft).
18.Bleed brake system.See Adjustment.
NOTE: To ensure correct operation, the
ABS system MUST be tested using
TestBook.BRAKE CALIPER - FRONT
Service repair no - 70.55.02
Remove
1.Loosen front road wheel nuts.
2.Raise front of vehicle.
WARNING: Support on safety stands.
3.Remove road wheel.
4.Remove split pins from pad retaining pins.
5.Remove brake pad retainers and springs.
6.Remove brake pads and shim if fitted.
7.Pull back brake hose shield.
8.Clamp brake hose using a suitable clamp.
9.Position container beneath brake caliper to
collect spillage.
10.Loosen brake pipe union and disconnect from
caliper.
11.Plug brake pipe and caliper connections.
12.Remove 2 bolts securing caliper.
13.Remove brake caliper.
ProCarManuals.com

70BRAKES
8
REPAIR Refit
14.Clean caliper to hub mating faces.
15.Position caliper to hub, fit bolts and tighten to82
Nm (60 lbf.ft).
16.Remove plugs from pipe to caliper connections
and wipe.
17.Connect pipe to caliper, tighten union to15 Nm
(11 lbf.ft).
18.Apply a light film of grease to rear of brake pads.
19.Fit pads to calipers.
From 02MY, ensure pads are correctly fitted,
with leading edge chamfer fitted as shown.
20.Fit pad retainers and springs.
21.Fit split pins to retainers.
22.Remove brake hose clamp.
23.Bleed brakes.See Adjustment.
24.Depress brake pedal to seat pads onto discs.
25.Fit road wheels, remove axle stands and tighten
nuts to130 Nm (96 lbf.ft).BRAKE CALIPER - REAR
Service repair no - 70.55.03
Remove
1.Loosen rear road wheel nuts.
2.Raise rear of vehicle.
WARNING: Support on safety stands.
3.Remove road wheel.
4.Remove split pins from brake pad retaining pins.
5.Remove brake pad retaining pins.
6.Remove brake pad retainer springs.
7.Remove brake pads and shim if fitted.
8.Position container beneath brake caliper to
collect spillage.
9.Loosen brake pipe union and disconnect from
caliper.
CAUTION: Plug the connections.
10.Remove 2 bolts securing caliper.
11.Remove brake caliper.
ProCarManuals.com

BRAKES
9
REPAIR Refit
12.Clean caliper to axle bracket mating faces.
13.Position caliper to axle bracket, fit bolts and
tighten to82 Nm (60 lbf.ft).
14.Remove plugs from pipe and caliper.
15.Clean brake pipe union and caliper.
16.Connect pipe to caliper, tighten union to15 Nm
(11 lbf.ft).
17.Apply a light film of grease to rear of brake pads.
18.Fit brake pads.
From 02MY, ensure shims are correctly fitted,
see illustration.
NOTE: Vehicles from 02MY have leading
and trailing edge chamfers on rear pads.
19.Fit pad retainer springs.
20.Fit brake pad retaining pins and secure with new
split pins.
21.Bleed brakes.See Adjustment.
22.Depress brake pedal to seat pads onto discs.
23.Fit road wheels, remove axle stands and tighten
nuts to130 Nm (96 lbf.ft).SWITCH - STOP LIGHT
Service repair no - 70.35.42
Remove
1.Disconnect 2 Lucars from stop light switch.
2.Remove mastic from around switch.
3.Remove switch from pedal box.
Refit
4.Fit and tighten switch to pedal box.
5.Apply mastic to switch.
6.Connect 2 Lucars to switch.
ProCarManuals.com

CHASSIS AND BODY
1
ADJUSTMENT TAIL DOOR STRIKER
Service repair no - 76.37.25
Check
1.Before adjusting door striker, ensure spare
wheel is fitted to tail door.
Adjust
1.Loosen bolts securing striker.
2.Adjust striker and tighten bolts to10 Nm (7
lbf.ft).
3.Close door and check for correct latching.
ProCarManuals.com

76CHASSIS AND BODY
4
REPAIR WING - FRONT
Service repair no - 76.10.24
Remove
1.Remove wheel arch liner.See this Section.
2.Remove front grille.See this Section.
3.Release fixings and remove cooling fan cowl.
4.Remove air cleaner grille from front wing.
5.Remove 4 screws securing air intake elbow to
wing.
6.Remove 7 screws and remove heater air intake
grille from wing.
7.Remove 2 bolts securing heater air intake
bracket to inner wing. Remove bracket.
8.Remove heater air intake from wing and collect
seal.
9.Remove 2 bolts securing EGR solenoid to inner
wing and lay aside.
10.Remove 3 studs securing expansion tank pipe to
inner wing.
11.Remove 2 bolts securing PAS reservoir to inner
wing and lay aside.
12.Remove 4 bolts securing outer wing to inner
wing.
ProCarManuals.com

CHASSIS AND BODY
5
REPAIR
13.Remove 4 bolts securing radiator mounting
bracket to wing.
14.Loosen screw and release bonnet lock inner
cable from bonnet lock.
15.Release bonnet lock outer cable from from
bonnet lock.
16.Push centre pins from studs securing wheel arch
extension to wing, remove studs and remove
wheel arch extension.
17.Remove bolt securing inner and outer wing to
chassis.
18.Remove nut and bolt securing support stay to
wing.
19.Remove 4 bolts securing wing to’A’post.
20.Remove bolt securing wing to bulkhead.
ProCarManuals.com