Power Door Locks
- All Models Without Keyless Entry
G551
[t.dE-l=
- ---- --:[
l'!fi:i- ".",.1
l'! l-------- r I
li I I
*"I!'k------#-r*.*rq;,pft?is,,,flr::fi
| : I I c"u,',", i c"",o"" i 21 i cs03 security'
I i"x[v*fl
i$k------+-----=#f;ffi svseni
I i t I ou*."jJ*"'l '** '"*J"l ^,,**0, #'#[""j,% i
I i ! I &H'E5o I ,ig^* d$n* |
.e&.s8usA usA ; 'o'"rto it,Ii
lrr!
-"ll'**n*ru;X,*#",XHm,
i
lil I
| :.--!---i
| .L-J iiriioflil", iffffliii F$fl,H"- itJ !F$$,i$", iI l-T;1-li"3g5"= iioriibl-r'-" 1 iffi !
I lunr.ocx I rccK IswrrcH : Lunl----i L!flJI l"'*^1 *-l- - i sreREo RADro srEREo RADro
t --t , ,--- ",r*- :
UNDER.HOODFUSE/RELAYBOXi--r?Grs;-'ir oooF Locx I
L__{g:":l9 Y C3sl
'n',o"n I iE?Loo'
I see PowerIl Distribution.I ^r^a llr-i,
"*,:TI
Bdt6rynpur
Unlock LockGround input input
130
'='99-'00 models
\lr
POWERoooR LocKCONTROL UNITPHOfO90vtEw37
UnlocULock lock Unlockinput control ot lputLockourpur
YEUBED
1YEUFED
r
c557PHO|Q93vlEw 62
c654
FRONT .PASSENGER'S 'DOOR LOCK , 6
ACTUATORvlEW 6
c664
DooR LocK iACTUATOR ,
DOORKEY
4
BLU/
WHT/RED
cA14iu-o16ez wHT/FEO
DRIVER'SDOOR 4
LOCKACTUATOR
c634FED
LEFT REAR .DOOR LOCKACTUATORPHA|O 95 WHT/REO
WHT/FEO
FED
I YEL/
c654PHO|A 921YEUBED
c67 4
c570
vlEW 5
YEURED
BLK
BLK
WHT/BEO, WHT/FED
I wHT/REo
c664
c571
\
;ffi
130-1
Power Door Locks
- '96-'98 Models With Keyless Entry
(NotUsed)
c562(Ssdan 5)
lOY,laEntcalYatrt oil
SeeCeiling
"*. IPHaTo 611
""#!
__ It
Seenorns
,J:l
ffi
!l*1'*
Rf,Ltr: a ?'* seePower IU6il'
il"d!rui' i.^h::Eii:,_J"'"'ou
t 12 't( 9_s!-1 .
",.*.*,.
1 ".*..1 i#??'o
sYsrEM coNNEcroR (oPTroN) -?
1 UNDER-FUAE 14I t rusE r4: Grul8E COirIFOL)I / 0(Enr38)See Power i ? 7.1 c.. o.Di8tributlon. ! | X;i*:
I DASHI FUSE/I RELAY
STEREO RADIOTUNERPHOTO 73vlEW 68
cs03
css6
;f,;z3,'9,*-
14n 22
BLU/ N WHT/ II YEUWHTI ALK I ALU
B11l'B12l.B13
'I tF;?,'
-xlru
c5l6
86 |' 83
''tl
*, **
t"
[ro**:"[fi*'
""i,
;: I;"il"."'Y' o-ft 3[tnlt$ro" Fi:a
I "* |
F,%',3,, (o"''on)
ir?rt,:*,"." I """,,":
See lgnitionKey Reminder
door ooen. ' pHoro s7 .------- Sa.lan -
f - | csre iofiib$'-" "c,s;rg,_ !
'
| ! "* I
"i3tr9"" 'LU,RED I GnNioR,.
!=4 ,. L----- --,1"n,,'.
-'-l i
i*-i---- ll}gii I
*,*"1
I r7r------'t TNTEGMTED I RELAY I Irrlll,l.I INTECru$ED I RELAY| * s€€ | cotlrRol lBox
LJaBIEIIL i9,Fis," ieHo'osa
BLU/HEO
2
Btu/,|\mr
C415 STEERINGPHOTO 60LOCK
I
I
I
BLUAIIXT
Hffirp;,ruml*-*i E;ffi*,ru
4
ALK
-- ---- J
c415
YtEw 14 sss G,g{rndarr< Olstrlhdion,
RIGHTREARDOORswrTcHClosed withdoor open.
""L___J
G401
130-2
rl
lt,
I vevneo
I veuneo.1I YEUFED
UNDER-HOODFUSE/RELAYBOXi-iffiri
""',;Xftf*',I.'
c557
vtEw 62
c654
FRONT
;l
I
see Power iDistribution. I**t"t:.""."
I
------*-,7
OE
n"r,n"n I
il.",":['
".,"-fifiT""' I
-:iii[::f
PASSENGER'SDOOR LOCKACTUATOR
c554
c557
. VIEW 62
cs56
vtEw61WHT/REO
POWERDOORLOCKCONTROLUNIT
GRN/OBN
tu
GFI{/OBN:
GRN/OFN
ALUAViIT
DOORKEY
4
BLUAVHT
c556PHOfO93vtEw 61
BLU/NED
c634
92YEURED
DRIVER'SDOORLOCKACTUATORDOORLOCKKNOB
DRIVER'SDOOR LOCKswlTcH
WHT/FED
1
I
BLK
22
BLK
I-
c556
vtEw61BLK
YEUFEO=__- , YEUFEO
c5zo : sPHO|O 99 ,VIEW 5 - YEUFEO
C674 ' 1PHO|O95
PHOTO 95 I WHI/REO
C674PHOTO9sI WHT/FEDc570PHOTO ggvtEw 5 . _ryHi/!E9
ACTUATOR .-.:PHO|O 95FED
c664 2PHA|A9S wxf/FED
c571 2
VIEW6 WHT/BEO
Driver'sdoor Batt€ryunlock input input
Unlock Lockanput input
Unlock/loc*ouIpur
Ground
Unlock/lockLock outputinput
[-:I
l_l
t fl!@Klocx
eLxlrat-{ 3'i#i:T:'
!- cssr
Il r
S€s Ground
130-3
Power Door Locks (cont'd)
- How the Circuit Works
Keyless Entry System
The keyless door locks combine the power door
locks with a remote keyJob transmitter. The keyless
receiver unit is part of the radio. The keyless
receiver unit receives direct inputs f rom the ignition
key switch, the passenger door switches, and an
indirect input trom the driver's door switch through
the integrated control unit.
Power Door Locks (With or Wlthout Keyless)
The power door lock system is made up of the
oower door lock control unit. driver's door lock
switch, and individual door lock actuators. The
power door locks are controlled by the driver's door
lock switch and the driver's door lock actuator
switch.
Transmitter (With Keyless Entry)
The transmitter sends coded radio wave signals to
the keyless receiver unit when one ot its buttons is
pressed. Each transmitter has a unique code that
must be 'laught" to the keyless receiver unit before
it can operate the door locks or any other lunction.
Up to 4 transmitters can be programmed to operate
the keyless door locks.
Door Locking (With or without Keyless Entry)
When you push the driver's door lock switch to the
lock position, ground is applied to the GBN/IVHT
wire to the oower door lock control unit. The control
unit then applies battery voltage to the WHT/RED
wire and ground to the YEURED wire. The
passenger door lock actuators then activate to lock
the corresponding door locks.
When you lock the driver's door with the key or door
lock knob, it is mechanically locked, and the driver's
door lock actuator switch applies ground to the
oower door lock control unit. The control unit then
applies battery voltage to the WHT/RED wire and
ground to the YEURED wire, activating the
passenger door lock actuators which lock the doors.
Dool Locking with Transmitter
When you press the LOCK button on the remote
transmitter, the power door lock control unit applies
battery voltage to the WHT/RED wire and ground to
the YEURED wire. The passenger door lock
actuators then activate and lock the doors. A ground
slgnal is also applied to the BLU/RED wire to lock
the driver's door. lf any door is open, you cannot lock
it using the remote transmitter.
Door Unlocking (With or Without Keyless Entry)
When you push the driver's power door lock switch
to the unlock position, ground is applied to the
GRN/ORN wire to the power door lock control unit.
The control unit then applies battery voltage to the
YEURED and BLU/RED wires and ground to the
WHT/RED wire. The door lock actuators then
activate to unlock the doors.
When you unlock the driver's door with the key or
the door lock knob, it is mechanically unlocked; the
other doors do not unlock.
Door Unlocking (With Transmltter)
When you press the UNLOCK button on lhe remote
transmitter once. the power door lock control unit
applies battery voltage to the WHT/RED wire and
ground to the BLU/RED wire to unlock the driver's
door. When you press the UNLOCK button twice,
the control unit then applies ground to the YEURED
wires to activate the passenger door locks. lf you do
not open a door within 30 seconds after unlocking
the doors with the transmitter, the doors
automatically relock.
Transmltter Programming
1 . Turn the ignition switch ON (ll).
2. Press and hold the Valet-Disarm button on the
radio (between the AM/FM button and the
CD/TAPE button) to enter the programming
mode. (Continue to hold the button during the
procedure, or programming will be cancelled.)
Check that the power door locks cycle to confirm
that you're in the programming mode.
3. Press the "LOCK' or "UNLOCK' button on the
transmitter. Check that the power door locks
cycle to confirm that the code was accepted.
4. Press the "LOCK" or "UNLOCK" button on each
of the remaining transmitters. (You can program
up to four transmitters per vehicle.)
5. After all the transmitters have been
programmed, release lhe Valet-Disarm button to
exit the programming mode.
Beep On/Oft Feature
'I . Press and hold the LOCK and OPTION buttons
on the transmitter.
2. Watch the transmitter's LED:
One flash: Beeo activated.
Two tlashes: Beeo deactivated.
130-4
Power Door Locks (cont'd)
Keyless Receiver Unit Input Test
The following tests are pertormed with A (Main) and B (Keyless) disconnected from the audio unit.
TerminalNo.WireColorTest ConditlonTest: Desired RasultPossible Cause it resull is not obtained
4WHT/BLUUnder all conditionsCheck for vollage to ground:
There should bs batteryvoltage.
aBlown No. 47 (7.5A) tuse in the
under-hood fuss/relay box
An open in the wireo
5YEUREDlgnition switch ACC (l)Check lor voltage to ground:
Th€re should be battery
voltage.
aBlown No. 28 (10A) fuse in the
underdash fusg/relay box
An open in the wirea
TerminalNo.WireColorTest CondiiionTest: Desired ResultPossible Cause if rssult i3 not obtalned
BLU/RED
lgnition key insertedinto the ignition key
switch
Check for voltage to ground:
There should bs 1 V or less.aPoor ground (G401, G402)
Faulty ignition key switch
An open in the wire
Short in the wire
a
a
algnition key r€moved
trom the ignition key
switch
Check lor voltage to ground:
There should be 4 V or more.
3BLUI/ELUnder all conditions
Check for continuity betweenthe audio unit 16P connectorNo- 3 terminal and power doorlock control unit 12P connsctorNo. 6 terminal: There should
be continuity.
I An open in the wire
6BLK/YELlgnition switch ON (ll)Check for voltage to ground:
Thers should be batteryvollage.
. Blown No. 14 (7.5A) fuse in the
under-dash fuse/relay box
. An open in the wire
8LT GRN/BLKCeiljng light switch in"middle position"Connect to ground: The ceilinglight should come on.
aBlown No. 43 (7.5A) fuse in the
undsr-hood fuse/relay box
Blown ceiling light bulb
Faulty ceiling light
An open in the wire
a
a
o
14LT GRN/REDEach door oponed,one at a timeCheck for continuity to ground:
There should be continuity.
aFaulty door switch
An open in lhe wirea
tcBLKUnder all conditionsCheck for continuity to ground:
There should b€ continuity.
aPoor ground (G401, G402)
An open in the wirea
16GRYUnder all conditionsConn€ct to ground:
Horn should sound.
. Blown No.52 (15A) fuse in the
under-hood tuse/relay box
. Faulty horn
. Faulty horn relay
. An open in the wire
130-6
Power Door Locks (cont'd)
Keyless Entry Does Not Work In Any
Mode
NOTE: Before beginning, verify that all the
transmitters are programmed to the vehicle.
1 . Does the radio work properly?
Yes - Go to step 9.
No - Go to the neld step.
NOTE: For steos 2 - 8. refer to the schematic dia-
gram for the Stereo Sound System on page 150.
2. Are fuses 28 (in the under-dash fuse box) and
fuse 47 (in the under-hood fuse box) OK?
Yes - Go to step 4.
No - Replace the blown fuse, then go to the
nen steo.
3. Does the fuse blow again?
Yes - Locate and repair the short.
No- Retest the system.
4. ls the vehicle equipped with the optional security
system?
Yes - Go to the next steP.
No - Go to steD 6.
5. Does the keyless entry work correctly when the
security control unit connector is disconnected?
Yes - Faulty security system, go to security
system for f urther troubleshooting.
No - Go to the next step.
6. ls there battery voltage at terminal 4 of the radio
main harness connector (A)?
7.
=A
Yes - Go to the nen step.
No - Locate the open in the wiring between
tuse 47 and the radio.
ls there battery voltage at terminal 5 of the radio
main harness connector (A), when the ignition
switch is in the ACC (l) or ON (ll) position?
Yes - Go to the next step.
No - Locate the open in the wiring between
fuse 28 and the radio.
130-8
8. ls there continuity from terminal 14 of the radio
main harness connector (A) to ground?
Yes - Replace the radio.
No - Repair the open in the wiring between the
radio and the ground (G501).
9. Does the transmitter LED come on when any ot
the buttons are oressed?
Yes - Go to steo 12.
No - Go to the next steo.'10.ls the transmitter battery installed with the
positive side facing up?
Yes - Ensure that the battery contact tabs are
repositioned, then replace the battery.
Remove the key from the ignition, then
close the doors and trunk. Press the
LOCK button on the transmitter six times,
then go to the next step.
No - Ensure that the baftery contact tabs are
repositioned, then reinstall the batlery
correctly. Then reprogram the transmitter
and retest it. Use the procedure on page
1 30-4 f or transmitter programming.
11 . Does the transmitter LED come on when any of
the buttons are oressed?
Yes - Go to the next step.
No - Replace the transmitter and program it by
using the procedure on page 130-4.
12.Does the system work properly in all modes?
Yes - Finished. The system is OK.
No - Go to the next steD.
Power Door Locks (contd)
Doors Do Not Unlock Or Lock With
The Transmitter
1. Do the door's unlock and lock when usinq the
driver's door lock switch?
Yes - Go to the next step.
No - Repair the power door lock system.
2. Does the transmitter LED come on when anv of
the buttons are oressed?
Yes - Go to the next steo.
No - Check the transmitter battery, then retest.
It lhe doors still do not unlock or lock with
the transmitte( go to the next step.
Recheck with a known good transmitter
reprogrammed to the vehicle. Does the system
work properly in all modes.
Yes - Replace and program the transmitter,
then retest. Use the procedure on page
1 30-4 f or transmitter programming.
No- Gotothe next step.
Run a jumper wire from terminal I of the keyless
entry harness connector (B) to ground.
Do the doors unlock?
Yes - Go to the next steD.
No - Repair the open in the terminal 9
(GRN/ORN) wire.
130-10
5. Run a jumper wire from terminal 10 ol the
keyless entry harness connector (B) to ground.
Do the doors lock?
ves - Go to ttie next steo.
No - Repair the open in the terminal 10
(GRN/vVHT) wire.
Does the voltage at terminal 1 of the keyless
entry harness connector (B) change from battery
voltage when the key is not in the ignition, to
less than 1 volt when the key is in the ignition?
7.
Yes - Go to the next step.
No - Replace the ignition switch or repair the
damaged terminal 1 (BLU/RED) wire.
Does the voltage at terminal 14 of the keyless
entry harness connector (B) change from battery
voltage when all the doors are closed, to less
than 1 volt when any door is opened?
Yes - Replace the radio.
No - Repair the open in the terminal 14
(LT GRN/RED) wire.