1999 GMC C-SERIES engine coolant

yellowblue
v
For example,
these symbols
are used on an
original battery:
CAUTION
POSSIBLE
INJURY
PROTECT
EYES BY
SHIELDING
CAUSTIC
BATTERY
ACID COULD
CAUSE
BURNS
AVOID
SPARKS OR
FLAMES
SPARK OR
FLAME
COULD
EXPLODE
BATTERY
These symbols
are important
for you and
your passengers
whenever your
vehicle is
driven:
DOOR LOCK
UNLOCK
FASTEN
SEAT
BELTS
POWER
WINDOW
AIR BAG
These symbols
have to do with
your lamps:
MASTER
LIGHTING
SWITCH
TURN
SIGNALS
PARKING
LAMPS
HAZARD
WARNING
FLASHER
DAYTIME
RUNNING
LAMPS
FOG LAMPS
These symbols
are on some of
your controls:
WINDSHIELD
WIPER
WINDSHIELD
WASHER
WINDSHIELD
DEFROSTER
REAR
WINDOW
DEFOGGER
VENTILATING
FAN
These symbols
are used on
warning and
indicator lights:
ENGINE
COOLANT
TEMP
BATTERY
CHARGING
SYSTEM
BRAKE
COOLANT
ENGINE OIL
PRESSURE
ANTI-LOCK
BRAKES
Here are some
other symbols
you may see:
FUSE
LIGHTER
HORN
SPEAKER
FUEL
Vehicle Symbols
These are some of the symbols you may find on your vehicle.
ProCarManuals.com

2-
yellowblue
2-1
Section 2 Features and Controls
Here you can learn about the many standard and optional features on your vehicle, and information on starting,
shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything is
working properly
-- and what to do if you have a problem.
2
-2 Keys
2
-4 Door Locks
2
-5 Theft
2
-5 New Vehicle ªBreak-Inº
2
-6 Ignition Positions
2
-7 Starting Your Gasoline Engine
2
-10 Starting Your Diesel Engine
2
-13 Engine Checks Before Operating
2
-15 Engine Coolant Heater (If Equipped)
2
-16 Diesel Engine Exhaust Brake
2
-17 Two-Speed Rear Axle Electric Shift Control
(If Equipped)
2
-20 Automatic Transmission Operation
2
-22 Manual Transmission Operation
2
-23 Parking
2
-29 Parking Over Things That Burn
2
-29 Engine Exhaust2
-30 Running Your Engine While You're Parked
(Automatic Transmission)
2
-30 Windows
2
-31 Tilt Wheel (If Equipped)
2
-32 Turn Signal/Multifunction Lever
2
-39 Trailer Brake Hand Control Valve (Option)
2
-40 Inter-Axle Differential Lock Control
(If Equipped)
2
-41 Rear Axle Differential Lock Control
(If Equipped)
2
-42 Engine Air Control (If Equipped)
2
-43 Exterior Lamps
2
-46 Interior Lamps
2
-46 Mirrors
2
-50 Instrument Panel
2
-52 Instrument Panel Cluster
2
-55 Warning Lights, Gages and Indicators
ProCarManuals.com

yellowblue
2-10
Starting Your Diesel Engine
If you have a Caterpillar diesel engine, also refer to
your Caterpillar
Operation & Maintenance Manual for
starting procedure.
To make starting easier in cold weather (below 32F or
0C), the proper viscosity engine oil should be used. It's
also best to heat the engine oil first. You can do this by
using an engine coolant heater. A GM Automatic Ether
Injection System aids cold weather starting.
NOTICE:
Your diesel engine has an electric air intake
heater system which reduces white smoke and
helps start the engine in cold weather. Do not
spray starting fluid into the air intake where it
can contact the heater elements.
If you don't have the GM Automatic Ether
Injection System, don't use starting fluid or
you could damage your engine. If you have the
GM system, use only GM approved starting fluid
that has been tested to establish compatibility
with the air inlet heater system.
NOTICE:
If you ever have to have your vehicle towed, see
the part of this manual that tells how to do it
without damaging your vehicle. See ªTowing
Your Vehicleº in the Index.
Restarting the Diesel Engine While Moving
(Automatic Transmission)
If you have to restart the engine while the vehicle is
moving, you'll first have to shift the automatic transmission
to NEUTRAL (N). This safety feature prevents starting
the engine when the transmission is in a drive gear.
Stopping the Diesel Engine
If you have a Caterpillar diesel engine, see your
Caterpillar
Operation & Maintenance Manual.
1. Set the parking brake and shift to NEUTRAL (N) or
PARK (P).
2. Turn the ignition switch key to OFF.
If your vehicle has a two
-speed axle, see ªRear Axle,
Tw o
-Speed Electric Shift Controlº or ªRear Axle,
Tw o
-Speed Airshift Controlº in the Index.
ProCarManuals.com

yellowblue
2-11 Cold Weather Starting (Caterpillar

Diesel)
Because the diesel engine uses compression ignition, it
is harder to start in cold weather than a gasoline engine.
The air intake heater and use of the proper engine oil,
optional engine coolant heaters and optional ether
injection systems help cold weather starting. See the
Caterpillar

Operation & Maintenance Manual for
more information.
Diesel Engine Warm-Up
Several factors affect how quickly your diesel engine
warms up. These can include outside temperature,
engine load, idle time and your vehicle's option content.
Your vehicle may be equipped with some features that
can help the engine reach operating temperature sooner.
Some of these features are discussed below.
Also, remember that an automatic transmission adds
heat to the cooling system through the heat exchanger in
the radiator. Because of this, vehicles equipped with
automatic transmissions are often able to retain engine
coolant heat better than manual transmission vehicles.
See your Caterpillar

Operation & Maintenance manual
for additional diesel engine warm
-up information.
Engine Automatic Shutdown (If Equipped)
Your CHECK GAGES light will come on if the system
senses high engine temperature or low engine oil
pressure. If high engine temperature is detected, you
will also hear a tone alarm at two beats per second. The
alarm and the light will remain on until the condition is
fixed. If the engine temperature condition worsens, the
tone alarm will go to five beats per second. When a low
oil pressure condition is detected, the five beat per
second alarm will come on immediately.
If the system senses low engine coolant, the five beat
per second alarm and the LOW COOLANT warning
light will come on.
The five beats per second tone alarm means that your
engine will shut down in 25 seconds. Pull off the road
and shut off the engine. Don't start it until the reason for
the problem is known, and the problem is fixed. If the
engine shuts down when you are still in traffic, you can
restart the engine and get another 25 seconds of
operation. Do this only if you have to, since there is a
problem that can harm the engine if it isn't fixed.
ProCarManuals.com

yellowblue
2-13
The manual fast idle feature is activated by pressing the
switch on the instrument panel. When the switch is
pressed again, or any of the previous conditions are not
met, manual fast idle will be deactivated.
Manual fast idle can be used to set any desired idle
speed. To set a new temporary engine idle speed:
1. Make sure all of the previously described conditions
are met.
2. Press the accelerator pedal to the desired engine speed.
3. Momentarily press the manual FAST IDLE switch.
The temporary idle speed will be set. This new rpm
level will be remembered by the system until either the
ignition is turned to OFF or a new idle speed is set.
Radiator Shutters -- Caterpillar

(If Equipped)
Radiator shutters aid engine warm-up by blocking the
airflow through the radiator and charge the air cooler to
conserve heat in cold conditions.
The radiator shutters on your vehicle (if equipped)
operate automatically. When the ignition switch is in
RUN or START and the engine temperature is below
195F (90C), the shutters will close, blocking the flow
of air through the radiator and charge the air cooler.When the engine temperature reaches 195F (90C), the
shutters will open to the normal operating position.
Engine Checks Before Operating
When you've started your engine, let it run for 20 to
30 seconds before you put a load on the engine.
But don't leave the vehicle while the engine is running.
During this warm
-up period, check your warning lights
and gages:

If oil pressure doesn't begin to rise within 15 seconds
of starting, stop the engine and find the cause.

If the engine coolant temperature gage needle goes
into the hot area on the gage, stop the engine and
find the cause of the overheating.

If you have air brakes, the dual
-needle air pressure
gage should read at least 105 psi (720 kPa) for both
service systems before you try to move the vehicle.
When air pressure is below 60 psi (420 kPa), the
LOW AIR light will come on and you will hear a
tone alarm. If the pressure doesn't build up or drops
during warm
-up, stop the engine and find the cause
before you try to move the vehicle. Recommended
air pressure before actually driving away is
120 psi (830 kPa).
ProCarManuals.com

yellowblue
2-14

The charging system light should come on when the
ignition switch key is turned to RUN or START and
should go out when the engine is running above idle.
If the light doesn't go out or comes back on during
normal engine operation, have the charging system
checked right away. (This light tells you if the
generator is not charging; it doesn't reflect the
condition of the battery.)

The voltmeter charge indicator gage tells you the
condition of your battery's charge. The gage should
be in the center area during engine operation. The
red area on the left indicates an undercharge
condition; the red area on the right indicates an
overcharge. If the gage is in either red area, have the
battery and charging system checked right away.
NOTICE:
Don't allow the engine to operate at low idle for
more than five minutes. This can cause low
engine operating temperatures which can affect
engine operation and reduce engine life. Engine
idle speed should be increased to 1200 rpm
whenever extended idle is required. Once started,
the engine should be placed under load to allow
the engine coolant temperature to reach
150F (66C) before shutting off the engine.
ProCarManuals.com

yellowblue
2-15
Engine Coolant Heater (If Equipped)
If your vehicle has this
feature, the plug
-in
receptacle is located behind
the front bumper as shown,
or in the component box
on the driver's side of
the vehicle.
In very cold weather, 0
F (
-18
C) or colder, the engine
coolant heater can help. You'll get easier starting and
better fuel economy during engine warm
-up. Usually,
the coolant heater should be plugged in a minimum of
four hours prior to starting your vehicle.
To Use the Engine Coolant Heater
1. Turn off the engine.
2. Find the plug
-in receptacle (either behind the front
bumper or in the component box).
3. Plug a heavy
-duty, three-prong extension cord
(rated for at least 15 amps) into the vehicle's plug
-in
receptacle first. Then plug the extension cord into a
normal, grounded 110
-volt AC outlet.
CAUTION:
Plugging the cord into an ungrounded outlet
could cause an electrical shock. Also, the wrong
kind of extension cord could overheat and cause
a fire. You could be seriously injured. Plug the
cord into a properly grounded three
-prong
11 0
-volt AC outlet. Use a heavy-duty three-prong
extension cord rated for at least 15 amps.
ProCarManuals.com

yellowblue
2-16
4. Before starting the engine, be sure to unplug the cord.
How long should you keep the coolant heater plugged
in? The answer depends on the outside temperature.
Above 32
F (0
C), the coolant heater is not required.
From 32
F to
-10
F (0
C to -23
C), keep the
coolant heater plugged in at least two hours. Below
-10
F (-23
C), keep the coolant heater plugged in for
a minimum of eight hours or overnight. It will not harm
either the coolant heater or the vehicle to leave the
coolant heater plugged in longer than the times stated.
Be sure to remove and store the cord before starting the
engine. See ªDiesel Fuel Requirements and Fuel
Systemº in the Index for information on what fuel to use
in cold weather.
Diesel Engine Exhaust Brake
The exhaust brake is available on vehicles equipped
with a diesel engine and air brakes (or an air
compressor). It is located in the exhaust system.
The switch is on the upper
right side of the instrument
panel and turns the exhaust
brake on and off.
The exhaust brake indicator light is on when the exhaust
brake is in use.
The exhaust brake is used to help slow the vehicle and
may assist the vehicle's foundation brakes. The use of the
exhaust brake will assist the braking of the vehicle and
prolong the life of the foundation brake lining material.
When using the exhaust brake, the proper gear range
selection is important. The exhaust brake will be most
effective if the gear range selected is the lowest possible
range that does not allow the engine rpm to go more than
200 rpm above rated (full load) rpm as shown on the
Engine Information Plate. (Do not exceed 2900 rpm.)
ProCarManuals.com