1999 DODGE RAM suspension

Fig. 7: Brakes, Steering, & Suspension
Fig. 8: Air Conditioning, Heater & Ventilation

WHEEL A LIG NM EN T S PEC IF IC ATIO NS

1999 D odge P ic ku p R 1500
1998-99 WHEEL ALIGNMENT
CHRY - Specifications & Procedures - Trucks & FWD Vans
Caravan, Dakota, Durango, Ram Pickup, Ram Van/Wagon,
Town & Country, Voyager
NOTE: Prior to performing wheel alignment, perform visual and
mechanical inspection of wheels, tires and suspension
components. See PRE-ALIGNMENT INSTRUCTIONS in WHEEL ALIGNMENT
THEORY & OPERATION article in GENERAL INFORMATION.
RIDING HEIGHT ADJUSTMENT
CHECKING PROCEDURE
NOTE: Information on vehicles not listed was not available from
manufacturer.
1999 Caravan, Town & Country, & Voyager
Before adjusting alignment, check riding height. Measure
height from inboard edge of fenderwell directly above center of wheel,
unless specified otherwise. Riding height must be checked with vehicle
on level floor, correct size tires properly inflated and fuel tank
full. Bounce vehicle several times and allow suspension to settle.
Visually inspect vehicle for signs of abnormal height from
front-to-rear and side-to-side. Check passenger and luggage
compartments for extra-heavy items and remove if present. Riding
height between left side and right side of vehicle should vary less
than 0.5 (12.7 mm). Information on riding height between front and
rear is not available from manufacturer. See RIDING HEIGHT
SPECIFICATIONS (1999 CARAVAN, TOWN & COUNTRY, & VOYAGER) table. If
riding height is not within specification, check, repair or replace
suspension components.
Dakota & Durango (4WD)
1) Measure and record distance between floor surface and
center of lower suspension arm rear mounting bolt head. Measure and
record distance between floor surface and center of front wheel. See
Fig. 1 . Subtract first measurement from second measurement. On Dakota,
difference between both measurements should be 1.725-1.975" (43.82-50.
16 mm). On Durango, difference between both measurements should be 2.
78-3.02" (70.6-76.7 mm).
2) If necessary, adjust height differential to specification.
Adjust each front suspension arm by rotating torsion bar anchor
adjustment bolt clockwise to raise vehicle and counterclockwise to
lower vehicle. Always raise vehicle to correct height. If vehicle
height is greater than maximum specification, lower height to less
than specification, then back up to specification. After each
adjustment, jounce vehicle before measuring height to determine
effects of adjustment.

Fig. 1: Measuring Riding Height (Dakota & Durango 4WD)
Courtesy of Chrysler Corp.
JACKING & HOISTING
FLOOR JACK
CAUTION: DO NOT place jack under any part of vehicle underbody. DO NOT
attempt to raise one entire side of vehicle by placing a jack
midway between front and rear wheels, as permanent body
damage could occur. DO NOT place jack under an axle tube,
aluminum differential, steering linkage, engine or
transmission oil pan, fuel tank or front suspension arm.
Caravan, Town & Country, & Voyager
To raise front end, place floor jack under front crossmember
forward flange, inboard of lower control arm pivot. To raise rear end,
place floor jack under rear axle, next to leaf spring mount. See
Fig. 2 .

Application Front - In. (mm) Rear - In. (mm\
)
Gas Engine With
14" & 15" Wheels (1) ....... 29.04-29.82
(737.5-757.5) .......... 29.76-30.54\
(756.0-776.0)\
Gas Engine With 15",
16" & 17" Wheels ( 2) ....... 29.27-30.05
(743.5-765.5) ........... 30.0-30.78\
(762.0-782.0)\
CNG & Electric Vehicles ..... 30.46-31.24
(783.5-803.5) ........... 31.2-31.98\
(792.5-812.5)\
( 1) - With tire sizes P205/75R 15 and P215/65R 15.
( 2) - With tire sizes P215/70R 15, P215/65R 16 and 215/65R 17.









\









\









\









\









\









\









\







HOIST
CAUTION: On Ram Van/Wagon, ensure there is adequate drive shaft
clearance while raising vehicle. DO NOT raise vehicle by
hoisting or jacking against front lower control arms. If rear
axle, fuel tank, spare tire and liftgate will be removed for
service, place additional weight on rear end of vehicle. This
will prevent tipping as center of gravity changes.
Caravan, Ram Van/Wagon, Town & Country, & Voyager
To raise vehicle on single and twin post type hoists, ensure
hoist pads contact vehicle frame behind front control arm pivots and
inside rear wheels on rear axle housing. Always use hoist adapters.
See Fig. 2 or 5.
Dakota & Ram Pickup
Vehicle may be raised on single or twin post swiveling arm,
or ramp-type drive hoists. If using swiveling arm hoist, ensure
lifting arms, pads or ramps are positioned evenly on frame rails, and
adequate clearance is maintained for transfer case (4WD models) or
skid plate. All hoists must be equipped with adapters to properly
support vehicle. See Fig. 3.
WHEEL ALIGNMENT PROCEDURES
FRONT WHEEL CAMBER & CASTER ADJUSTMENT
CAUTION: DO NOT adjust caster by heating or bending suspension
components. If caster angle is incorrect, replace
component(s) causing incorrect angle.
Caravan, Town & Country, & Voyager
1) Caster is factory preset and cannot be adjusted. Camber is
factory preset, but can be adjusted with a camber service kit. Raise
and support vehicle. While holding lower strut attaching bolts
stationary, loosen attaching nuts. See Fig. 6. Remove upper attaching
nut and bolt. Install camber service kit attaching/adjusting bolt and
nut. While holding bolt stationary, lightly tighten nut. Repeat
procedure for lower attaching nut and bolt.
2) Lower vehicle until vehicle weight is supported by
suspension. Bounce vehicle several times and allow suspension to
settle. Rotate new cam bolt to move top of wheel in or out to
specified camber. See WHEEL ALIGNMENT SPECIFICATIONS table. Tighten
through-bolt nuts to specification. See TORQUE SPECIFICATIONS table.

Fig. 6: Adjusting Camber (Caravan, Town & Country, & Voyager)
Courtesy of Chrysler Corp.
NOTE: Moving rear of control arm changes caster significantly.
Moving front of control arm changes camber significantly.
Fig. 7: Adjusting Camber & Caster (Dakota, Durango & Ram Pickup
With Independent Front Suspension)
Courtesy of Chrysler Corp.
Dakota, Durango & Ram Pickup (With Independent Front

Suspension)
Loosen pivot bar attaching bolts, and move ends of upper
control arm either in or out to obtain proper camber and caster
angles. See Fig. 7. See WHEEL ALIGNMENT SPECIFICATIONS table. Tighten
pivot bar retaining bolts. See TORQUE SPECIFICATIONS table.
Ram Pickup (Link/Coil Suspension)
Camber is factory set and is not adjustable. To adjust
caster, rotate adjuster cam on lower control arm. See WHEEL ALIGNMENT
SPECIFICATIONS table. See Fig. 8.
Fig. 8: Adjusting Caster (Ram Pickup With Link/Coil Suspension)
Courtesy of Chrysler Corp.
Ram Van/Wagon
1) Use Adjuster Tool 8199 for this procedure. See Fig. 9.
Clamp tool onto upper control arm frame bracket using 2 clamp bolts.
Tighten adjustment nut on each tool until bolts are snug against pivot
bar. Loosen both upper control arm retaining bolts completely.
2) To obtain proper camber and caster angles, tighten or
loosen tool adjustment bolts on adjuster tool to move one or both ends


WHEEL A LIG NM EN T T H EO RY/O PER ATIO N

1999 D odge P ic ku p R 1500
GENERAL INFORMATION
Wheel Alignment Theory & Operation
ALL MODELS
* PLEASE READ THIS FIRST *
NOTE: This article is intended for general information purposes
only. This information may not apply to all makes and models.
PRE-ALIGNMENT INSTRUCTIONS
GENERAL ALIGNMENT CHECKS
Before adjusting wheel alignment, check the following:
* Each axle uses tires of same construction and tread style,
equal in tread wear and overall diameter. Verify that radial
and axial runout is not excessive. Inflation should be at
manufacturer's specifications.
* Steering linkage and suspension must not have excessive play.
Check for wear in tie rod ends and ball joints. Springs must
not be sagging. Control arm and strut rod bushings must not
have excessive play. See Fig. 1.
Fig. 1: Checking Steering Linkage
* Vehicle must be on level floor with full fuel tank, no
passenger load, spare tire in place and no load in trunk.
Bounce front and rear end of vehicle several times. Confirm