1999 DODGE RAM transmission fluid
[x] Cancel search: transmission fluidPage 425 of 1691
![DODGE RAM 1999 Service Repair Manual 267 RBI ................................................ 7.0 (3.3)\
286 RBI
2WD ................................................... 6.8 (3.2)\
4WD ....................................](/manual-img/12/56915/w960_56915-424.png "DODGE RAM 1999 Service Repair Manual 267 RBI ................................................ 7.0 (3.3)\
286 RBI
2WD ................................................... 6.8 (3.2)\
4WD ....................................")
267 RBI ................................................ 7.0 (3.3)\
286 RBI
2WD ................................................... 6.8 (3.2)\
4WD .................................................. 10.1 (4.8)\
Ram Van/Wagon
248 RBI ................................................ 6.0 (2.8)\
(1) - Approximate drive axle capacity listed. Lubricant level should
be 1/2" below oil filler hole in axle housing cover.
\
\
\
\
\
\
\
FLUID TYPE
Use SAE 80W-90 for 286 models, or 90W for all other models,
hypoid gear lubricant with MIL-L-2105-C and API GL-5 ratings. Models
with Trac-Lok require addition of 6 ozs. (.18 L) Mopar(R) friction
modifier (limited slip additive). Ram Pickups equipped with Power-Lok
require addition of 8 ozs. (.24 L) Mopar(R) friction modifier.
TROUBLE SHOOTING
NOTE: See appropriate table in TROUBLE SHOOTING article in GENERAL
INFORMATION.
REMOVAL & INSTALLATION
REAR HUB, BEARINGS & AXLE SHAFT
Removal
Raise and support vehicle. Remove wheel. Remove bolts, axle
shaft and gasket. Remove nut lock from adjusting nut. See Fig. 1.
Remove adjusting nut and outer wheel bearing. Remove rear hub and
brake drum. Remove oil seal and inner wheel bearing (if necessary).
Installation
1) Pack wheel bearings with wheel bearing grease. Install
inner wheel bearing and oil seal in rear hub (if removed). Install
rear hub and brake drum. Install outer wheel bearing and adjusting
nut. Tighten adjusting nut to specification while rotating rear hub
and brake drum. See TORQUE SPECIFICATIONS table.
2) Back off adjusting nut approximately 1/8 turn to obtain .
001-.010" (.03-.25 mm) wheel bearing end play. Tap key lock into
adjusting nut and keyway on axle housing.
3) To install remaining components, reverse removal
procedure. Use NEW gasket when installing axle shaft. Tighten bolts to
specification. See TORQUE SPECIFICATIONS table.
DRIVE SHAFT
Removal
1) Raise and support vehicle. Ensure transmission and
transfer case selector levers are in Neutral. Remove wheel assembly.
Remove RWAL sensor, if equipped. Reference mark drive shaft to pinion
flange for reassembly.
2) On 2-piece drive shafts, scribe center carrier bearing-to-
frame bracket reference line for reassembly. On all drive shafts,
remove bolts and "U" joint straps at pinion flange. Remove center
carrier bearing bolts, if equipped. Remove spring clamps and brackets.
Remove drive shaft(s).
CAUTION: The "U" joint straps and bolts must be replaced. DO NOT
Page 470 of 1691
* D RIV ETR AIN S YSTE M S U NIF O RM IN SPEC TIO N G UID ELIN ES *
1 999 D odge P ic ku p R 1500
GENERAL INFORMATION
Drivetrain/Transmission Motorist Assurance Program
Standards For Automotive Repair
All Makes and Models
INTRODUCTION TO MOTORIST ASSURANCE PROGRAM (MAP)
CONTENTS
OVERVIEW OF MOTORIST ASSURANCE PROGRAM
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
Drive/Power Train Assemblies
AUTOMATIC TRANSMISSION/TRANSAXLE ASSEMBLIES
DIFFERENTIAL AND FINAL DRIVE ASSEMBLIES
MANUAL TRANSMISSION/TRANSAXLE ASSEMBLIES
TRANSFER CASE ASSEMBLIES
Drive/Power Train Components
ACTUATORS (ELECTRICAL)
ACTUATORS (VACUUM)
AXLES
BEARINGS AND RACES
BELL CRANKS
BELL HOUSINGS
BUSHINGS (EXTERNAL)
CABLES (SPEEDOMETER)
CABLES (TV, DETENT AND SHIFT)
CARRIER BEARINGS
CLUTCH CABLES AND CABLE HOUSINGS
CLUTCH DISCS (MANUAL TRANSMISSION)
CLUTCH FORKS
CLUTCH LINKAGES (MECHANICAL)
CLUTCH MASTER CYLINDERS
CLUTCH PEDALS
CLUTCH PIVOTS
CLUTCH PRESSURE PLATES
CLUTCH RELEASE BEARINGS
CLUTCH SLAVE CYLINDERS (CONCENTRIC)
CLUTCH SLAVE CYLINDERS (CONVENTIONAL OR EXTERNAL)
COMPANION FLANGES
CONNECTORS
COOLER BYPASS VALVES
COOLER LINES
COOLERS
CV JOINTS
DIP STICK TUBES
DIP STICKS (FLUID LEVEL INDICATORS)
DOWEL PINS, GUIDES AND PILOT HOLES
DRIVE SHAFT FLANGES
DRIVE SHAFTS AND HALF SHAFTS
DUST BOOTS
ENGINE MOUNTS
EXCITER RINGS
FILLER TUBES
FILTERS AND SCREENS
Page 471 of 1691
FLANGES
FLEX PLATES
FLUID LEVEL INDICATORS
FLUIDS AND LUBRICANTS
FLYWHEELS
FORCE MOTORS
GUIDES
HALF SHAFTS
HOSES, LINES AND TUBES
HOUSINGS (BELL, CASE, TAIL (EXTENSION) AND AUXILIARY)
INTERMEDIATE SHAFT SUPPORT BEARINGS
KEY INTERLOCK SYSTEMS
LIMITED SLIPS
LINES
LINKAGES (EXTERNAL)
LOCKING HUB ASSEMBLIES
LOCKING HUB CONTROL KNOBS
LUBRICANTS
METAL-CLAD SEALS
METALASTIC JOINTS
MODULATOR PINS
MODULATORS
MOUNTS (ENGINE, TRANSAXLE AND TRANSMISSION)
ODOMETER DRIVES (MECHANICAL)
ODOMETER HEADS (MECHANICAL)
OIL PANS
PANS
PILOT HOLES
PRESSURE PLATES
PRESSURE SWITCHES
RACES
RUBBER JOINTS (METALASTIC)
SCREENS
SEALS
SEALS (METAL-CLAD)
SELECTOR INTERLOCK SYSTEMS
SERVOS
SHIFT INTERLOCK SYSTEMS (SELECTOR AND KEY INTERLOCK SYSTEMS)
SENSORS
SIDE COVERS
SLIP YOKES
SOLENOIDS
SPEED SENSORS (ELECTRONIC WHEEL AND VEHICLE)
SPEEDOMETER-DRIVEN GEAR HOUSINGS
SPEEDOMETER/ODOMETER DRIVES (MECHANICAL)
SPEEDOMETER/ODOMETER HEADS (MECHANICAL)
SPEEDOMETERS AND ODOMETERS (ELECTRONIC)
SWITCHES
TONE WHEELS
TOOTHED RINGS (TONE WHEELS)
TORQUE CONVERTERS
TRANSAXLE MOUNTS
TRANSDUCERS (TRANSMISSION)
TRANSMISSION COOLERS
TRANSMISSION MOUNTS
TRANSMISSION PANS
TRANSMISSION RANGE INDICATORS (PRNDL)
TUBES
UNIVERSAL JOINTS (CARDON OR CROSS TYPE)
VACUUM CONTROLS
VACUUM HOSES
VACUUM MOTORS
VACUUM-OPERATED SWITCHES
Page 496 of 1691
Damaged, affecting
performance ............ A ............ Require replacement.
Missing ................. C ............ Require replacement.
Worn, affecting
performance ............ A ............ Require replacement.
\
\
\
\
\
\
\
LUBRICANTS
See FLUIDS AND LUBRICANTS .
METAL-CLAD SEALS
See SEALS.
METALASTIC JOINTS
See RUBBER JOINTS (METALASTIC) .
MODULATOR PINS
MODULATOR PIN INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Application incorrect ... B ............ Require replacement.
Missing ................. C ............ Require replacement.
\
\
\
\
\
\
\
MODULATORS
MODULATOR INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Bent, affecting
performance ............ A ............ Require replacement.
Contaminated (water, fuel,
etc.) .................. A ........ ( 1) Require replacement.
Housing cracked ......... A ............ Require replacement.
Inoperative ............. A ........ ( 2) Require replacement.
Leaking fluid
externally ............. A .. Require repair or replacement.
Leaking fluid
internally ............. A ............ Require replacement.
Leaking vacuum .......... A ............ Require replacement.
Nipple broken ........... A ............ Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
( 1) - Further inspection is required to determine the cause
of the contamination.
( 2) - Inoperative includes intermittent operation or out of OEM
specification.
\
\
\
\
\
\
\
MOUNTS (ENGINE, TRANSAXLE AND TRANSMISSION)
MOUNT (ENGINE, TRANSAXLE AND TRANSMISSION) INSPECTION \
\
\
\
\
\
\
Page 539 of 1691
Back-Up Lamp Switch On left side of transmission.
Brake Pressure Switch On combination valve.
Clutch Pedal Position Switch On clutch master cylinder
pushrod.
Low Washer Fluid Level Switch On side of washer fluid
reservoir.
Park Brake Switch On park brake mechanism.
Park/Neutral Position Switch
(A/T) On left side of transmission.
Seat Belt Switch Above left rear speaker.
Page 854 of 1691
IN STR UM EN T P A N EL - A N ALO G
1999 D odge P ic ku p R 1500
1999 ACCESSORIES & EQUIPMENT
CHRY - Analog Instrument Panels
Ram Pickup, Ram Van & Ram Wagon
DESCRIPTION & OPERATION
INSTRUMENT CLUSTER
All instrument cluster gauges are air core magnetic type.
Tachometer is optional. All gauges use data transferred on Chrysler
Collision Detection (CCD) bus. Instrument cluster incorporates a
Vacuum Fluorescent Display (VFD) for odometer display.
Brake warning light illuminates when ignition is on and
parking brake is applied. Brake warning light also illuminates if
brake hydraulic system failure occurs during service brake
application. Brake warning light bulb test occurs when ignition switch
is in START position.
Oil pressure warning light illuminates when engine oil
pressure is not sufficient to open oil pressure sending unit switch.
Oil pressure warning light bulb test occurs with ignition switch in
RUN position.
All instrument clusters include these analog gauges:
* Coolant Temperature Gauge
* Fuel Gauge
* Oil Pressure Gauge
* Speedometer
* Voltmeter
Instrument clusters include these indicator lights, if
vehicle is equipped with appropriate option:
* Air Bag
* Anti-Lock Brake System (ABS)
* Brake Warning
* Check Gauges
* Cruise On
* Headlight High Beam
* Low Fuel
* Low Washer Fluid
* CHECK ENGINE
* Overdrive Off
* Rear Wheel Anti-Lock (RWAL)
* Seat Belt Reminder
* Security
* Transmission Oil Temperature (A/T)
* Turn Signal
* Upshift (M/T)
* 4WD
SELF-DIAGNOSTIC SYSTEM
WARNING: Vehicle is equipped with an air bag system. To prevent air
bag deployment, disconnect negative battery cable and wait at
least 2 minutes before servicing instrument cluster. See
appropriate AIR BAG RESTRAINT SYSTEMS article.
CAUTION: When battery is disconnected, vehicle computer and memory
Page 887 of 1691
![DODGE RAM 1999 Service Repair Manual LUBRICATION SPECIFICATIONS TABLE - DIESEL \
\
\
\
\
\
\
M](/manual-img/12/56915/w960_56915-886.png "DODGE RAM 1999 Service Repair Manual LUBRICATION SPECIFICATIONS TABLE - DIESEL \
\
\
\
\
\
\
M")
LUBRICATION SPECIFICATIONS TABLE - DIESEL \
\
\
\
\
\
\
Material Condition Specification
\
\
\
\
\
\
\
\f
Engine Oil Ambient Temperature Above 10\bF SAE 15W-40
(
1) (-12\bC) To Over 30\bF (-1\bC)
\
\
\
\
\
\
\f
Ambient Temperature Less Than SAE 10W-30
0\bF (-18\bC) To Over 30\bF(-1\bC)
\
\
\
\
\
\
\f
Ambient Temperature Less Than With Block Heater:
-10\bF(-23\bC) Up To 0\bF (-18\bC) SAE 10W-30
Without Block Heater:
SAE 5W-30
\
\
\
\
\
\
\
\f
Engine All 50/50 Mixture Of
Coolant Distilled Water &
Ethylene Glycol
\
\
\
\
\
\
\
\f
Brake Fluid All DOT 3
\
\
\
\
\
\
\
\f
Automatic All ATF+2 Type 7176
Transmission
Fluid
\
\
\
\
\
\
\
\f
Transfer Case All ATF+2 Type 7176
Fluid Or DEXRON III ATF
\
\
\
\
\
\
\
\f
Manual All 75W-90 Synthc. API GL4
Transmission
Fluid
\
\
\
\
\
\
\
\f
Steering All Mopar Multi-Mileage
Linkage Lubricant
Lubricant
\
\
\
\
\
\
\
\f
Wheel Bearing All High Temperature Multi-
Grease -Purporse EP Grease
\
\
\
\
\
\
\
\f
Rear Axle All Mopar Hypoid Lubricant
Lubricant SAE 80W-90
(
2) GL-5 Gear Lube
\
\
\
\
\
\
\
\f
4x4 Front All Mopar Hypoid Lubricant
Axle SAE 80W-90
Lubricant GL-5 Gear Lube
\
\
\
\
\
\
\
\f
Power All Mopar Power Steering
Steering Fluid Or Equivalant
Fluid (
3) Petroleum Based
\
\
\
\
\
\
\
\f
Clutch All Multipurpose Grease
Linkage NLGI Grade 2 E.P.
Lubricant
\
\
\
\
\
\
\
\f
A/C All R-134a
Refrigerant
\
\
\
\
\
\
\
\f
A/C All Polyalkalene Glycol
Refrigerant SP10 PAG
Oil Refrigerant Oil
\
\
\
\
\
\
\
\f
Page 888 of 1691
(
1) - SAE 10W-30 engine oil is preferred for use in all Dodge
trucks. Use only API approved oil with Starburst Symbol.
(
2) - Axles with Limited-Slip Differentials require the use of
a 5% Friction Modifier, such as Mopar Gear Oil Additive
Friction Modifier.
(
3) - Never add gear oil, automatic transmission fluid or
hydroboost power steering fluid.
\
\
\
\
\
\
\
FLUID CAPACITIES - DIESEL
FLUID CAPACITIES TABLE - DIESEL \
\
\
\
\
\
\
Item Condition Specification (1)
\
\
\
\
\
\
\
\f
Engine Oil Capacity, Upper Safe Mark 10 Qts. (9.5L)
\
\
\
\
\
\
\f
Capacity, Lower Safe Mark 8 Qts. (7.5L)
\
\
\
\
\
\
\
\f
Engine Drained 26 Qts. (24.5L)
Coolant
\
\
\
\
\
\
\
\f
Automatic 46RE: Dry Fill 17 Qts. (16L)
Transmission
\
\
\
\
\
\
\f
Fluid 47RE: Dry Fill 17 Qts. (16L)
\
\
\
\
\
\
\
\f
Manual NV4500 4 Qts. (3.8L)
Transmission
Fluid
\
\
\
\
\
\
\
\f
Rear Axle DANA 70 Model 267 (2WD) 7 Pts. (3.3L)
Lubricant
\
\
\
\
\
\
\f
DANA 70 Model 267 (4WD) 7.8 Pts. (3.6L)
\
\
\
\
\
\
\f
DANA 80 Model 286 (2WD) 6.8.Pts. (3.2L)
\
\
\
\
\
\
\f
DANA 80 Model 286 (4WD) 10.1 Pts. (4.8L)
\
\
\
\
\
\
\
\f
Rear Axle Model 267 (2WD) 7 Pts. (3.3L)
Limited Slip
\
\
\
\
\
\
\f
Differential Model 267 (4WD) 7.8 Pts. (3.6L)
\
\
\
\
\
\
\f
Model 286 (2WD) 6.8 Pts. (3.2L)
\
\
\
\
\
\
\f
Model 286 (4WD) 10.1 Pts. (4.8L)
\
\
\
\
\
\
\
\f
Front Axle Model 248 7.6 Pts. (3.6L)
Lubricant
\
\
\
\
\
\
\
\f
Transfer Case NV241 HD 6.5 Pts. (3.1L)
Fluid
\
\
\
\
\
\
\
\f
Power Take NV021 4.6 Pts. (2.1L)
Off Adapter
\
\
\
\
\
\
\
\f
Power Drained 2.7 Pts. (1.3L)
Steering
Fluid
\
\
\
\
\
\
\
\f
A/C Charge Capacity 32 Oz. (.9Kg)
Refrigerant