1999 DODGE RAM warning light

colors, use terminal identification whenever possible.
1) If seat belt light is on, go to step 4). If seat belt
light is not on, go to next step.
2) Using DRB, select PASSIVE RESTRAINTS, AIRBAG AND MONITOR
DISPLAY. Read WARNING LAMP STATUS. If DRB does not display MIC S/B
LAMP STATE: OFF, replace instrument cluster. If DRB displays MIC S/B
LAMP STATE: OFF, go to next step.
3) If DRB displays ACM S/B LAMP REQUEST: OFF, replace ACM. If
DRB does not display ACM S/B LAMP REQUEST: OFF, replace instrument
cluster.
4) Using DRB, select PASSIVE RESTRAINTS, AIRBAG AND MONITOR
DISPLAY. Read WARNING LAMP STATUS. If DRB does not display MIC S/B
LAMP STATE: ON, replace instrument cluster. If DRB displays MIC S/B
LAMP STATE: ON, go to next step.
5) Using DRB, read WARNING LAMP STATUS. If DRB does not
display ACM S/B LAMP REQUEST: ON, replace instrument cluster. If DRB
displays ACM S/B LAMP REQUEST: ON, replace ACM.
REPAIRING VIN MESSAGE MISMATCH
NOTE: Perform AIR BAG VERIFICATION TEST after
all repairs. Each time a connector is disconnected, inspect
it to ensure it is in good condition. Always focus on circuit
being tested. Dirt, water and corrosion, are most common
problems in connectors. Due to manufacturer changes in wire
colors, use terminal identification whenever possible.
1) Using DRB, select ENGINE (PCM). If DRB displays NO
RESPONSE FROM PCM, perform REPAIRING SHORT TO BATTERY under VEHICLE
COMMUNICATIONS. If DRB does not display NO RESPONSE FROM PCM, and
vehicle is a Club Cab (BE), go to next step. If DRB does not display
NO RESPONSE FROM PCM, and vehicle is a Standard Cab (BR), go to step
3).
2) Using DRB, select PASSIVE RESTRAINTS, AIRBAG AND MONITOR
DISPLAY. Select VIN type to identify 7th digit of VIN (VIN 2 or 3 is
for Club Cab; VIN B is for a Standard Cab). If DRB does not display
PCM VIN: BE, replace powertrain control module. If DRB displays PCM
VIN: BE, replace ACM.
3) Using DRB, select PASSIVE RESTRAINTS, AIRBAG AND MONITOR
DISPLAY. Select VIN type to identify 7th digit of VIN (VIN B is for a
Standard Cab). If DRB does not display PCM VIN: BE, replace powertrain
control module. If DRB displays PCM VIN: BE, replace ACM.
WARNING LAMP CIRCUIT OPEN/SHORTED
NOTE: Perform AIR BAG VERIFICATION TEST after
all repairs. Each time a connector is disconnected, inspect
it to ensure it is in good condition. Always focus on circuit
being tested. Dirt, water and corrosion, are most common
problems in connectors. Due to manufacturer changes in wire
colors, use terminal identification whenever possible.
1) Using DRB, select MECHANICAL INSTRUMENT CLUSTER (MIC). If\
DRB displays NO RESPONSE FROM MIC, go to
NO RESPONSE FROM INSTRUMENT CLUSTER under VEHICLE COMMUNICATIONS. If
DRB does not display NO RESPONSE FROM MIC, go to next step.
2) Using DRB, select PASSIVE RESTRAINTS AIRBAG AND MONITOR
DISPLAY. Read WARNING LAMP status. If DRB does not display MIC BULB
STATE, replace instrument cluster. If DRB displays MIC BULB STATE, go
to next step.
3) If DRB does not display MIC DRIVER STATE OK, replace
instrument cluster. If DRB displays MIC DRIVER STATE OK, go to next

step.
4) Observe AIR BAG warning light. Turn ignition off and wait
5 minutes. After 5 minutes, turn ignition on (engine off). If AIR BAG
warning light comes on for 6 to 8 seconds, replace ACM. If AIR BAG
warning light does not come on for 6 to 8 seconds, replace instrument
cluster.
REPAIRING PAD SWITCH
NOTE: Perform AIR BAG VERIFICATION TEST after
all repairs. Each time a connector is disconnected, inspect
it to ensure it is in good condition. Always focus on circuit
being tested. Dirt, water and corrosion, are most common
problems in connectors. Due to manufacturer changes in wire
colors, use terminal identification whenever possible.
1) Using DRB, read active DTCs. If DRB displays LOSS OF
IGNITION RUN/START, go to LOSS OF IGNITION RUN/START. If DRB does not
display LOSS OF IGNITION RUN/START, go to next step.
2) Disconnect PAD switch 2-pin connector. Using a voltmeter,
check voltage between PAD switch 2-pin connector terminals No. 1
(Light Green/Yellow wire) and No. 2 (Black wire). If voltage is less\
than 10 volts, repair open in Light Green/Yellow wire. If voltage is
more than 10 volts, go to next step.
3) Turn ignition off. Using an ohmmeter, check resistance
between ground and PAD switch connector terminal No. 2 (Black wire).
If resistance is more than 5 ohms, repair open in Black wire. If
resistance is less than 5 ohms, replace PAD switch.
PAD SWITCH INDICATOR PROBLEMS
1) If PAD switch off indicator fails to illuminate in OFF
position, go to next step. If PAD switch off indicator does not fail
to illuminate in OFF position, go to step 5).
2) Using DRB, read active DTCs. If DRB displays LOSS OF
IGNITION RUN/START, go to diagnostic test for that DTC. If DRB does
not display LOSS OF IGNITION RUN/START, go to next step.
3) Disconnect PAD switch 2-pin connector. Turn ignition on.
Measure voltage between ground and PAD switch 2-pin connector Light
Green/Yellow wire. If voltage is more than 10 volts, go to next step.
If voltage is less than 10 volts, repair open in Light Green/Yellow
wire.
4) Turn ignition off. Measure resistance between ground and
PAD switch 2-pin connector Black/Pink wire. If resistance is less than
5 ohms, replace PAD switch. If resistance is more than 5 ohms, repair
open in Black/Pink wire.
5) Ensure battery is fully charged. Using DRB, read and
record both active and stored code(s). Erase stored codes. Check for
active DTC(s) in either PAD switch position. If PAD switch off
indicator illuminates in ON position, replace PAD switch. If PAD
switch off indicator does not illuminate in ON position, test
complete.
AIR BAG VERIFICATION TEST
1) Remove all jumper wires. Reconnect all previously
disconnected components (except battery). Turn ignition on and
reconnect battery. Connect DRB to data link connector. Using DRB,
erase stored codes.
2) Turn ignition off and wait 15 seconds before turning
ignition on. Wait one minute. Read active codes. If DRB displays any
active codes, perform appropriate diagnostic test. If DRB does not
display any active codes, go to next step.

13) On A/T models, ensure all electrical connectors are clean
and properly connected to electrical plugs on transmission case. On
all models, check for loose or defective electrical connections on
starter and starter solenoid.
MECHANICAL INSPECTION
Compression
Manufacturer does not provide information for checking
compression.
FUEL SYSTEM
AIR IN FUEL SYSTEM
NOTE: Air in the fuel system may cause hard starting, rough
running, excessive smoke, poor engine performance, engine
misfire, poor fuel economy and fuel knock. Air may enter fuel
system whenever fuel supply lines, fuel filter/water
separator, fuel injection pump, fuel injectors or high
-pressure fuel lines are removed or disconnected.
1) Inspect all low-pressure fuel lines from fuel tank to fuel
transfer pump, fuel heater and fuel filter/water separator for signs
of leakage. Inspect all high-pressure fuel lines for signs of leakage.
See FUEL INJECTOR & HIGH-PRESSURE FUEL LINES under FUEL SYSTEM.
2) After repairing fuel leak, bleed air from fuel system. See
FUEL LINE BLEEDING under FUEL SYSTEM in REMOVAL, OVERHAUL &
INSTALLATION - TRUCKS - DIESEL article.
FUEL HEATER
1) Fuel heater is located in fuel filter/water separator. See
Fig. 1 . Fuel heater uses a fuel heater temperature sensor for
controlling operation of the fuel heater.
2) A defective fuel heater may cause excessive wax build-up
in the fuel filter/water separator during cold ambient temperatures.
Wax build-up may cause hard starting, prevent engine from
accelerating, low power, Blue smoke or White smoke. For testing of
fuel heater and fuel heater temperature sensor, see SYSTEM & COMPONENT
TESTING - TRUCKS - DIESEL article.
FUEL HEATER RELAY
Ensure fuel heater relay, located in power distribution
center is installed correctly and that terminals are not corroded. For
fuel heater relay testing, see SYSTEM & COMPONENT TESTING - TRUCKS -
DIESEL article.
FUEL FILTER/WATER SEPARATOR
NOTE: A blocked or restricted fuel filter/water separator may cause
starting problems, prevent engine from accelerating, low
power or White smoke. If an excessive amount of water
collects in filter/separator in a short period of time, it
may be necessary to drain and clean fuel tank.
1) When ignition switch is first turned to ON position,
WATER-IN-FUEL (WIF) warning light should come on for 2 seconds to
perform bulb and wiring circuit test and then go off. WATER-IN-FUEL
(WIF) warning light is located on instrument panel, just below the

tachometer.
2) If WATER-IN-FUEL (WIF) warning light stays on, water
should be drained from fuel filter/water separator. To drain water
from fuel filter/water separator, ensure engine is not running. Place
drain pan below drain tube at fuel filter/water separator. See Fig. 1.
3) Rotate handle on drain valve forward, toward front of
vehicle to OPEN position. Drain valve is located near top of fuel
filter/water separator. See Fig. 1.
4) Allow water to drain until clean flow of diesel fuel
exists. Rotate handle on drain valve back to CLOSE position.
FUEL TRANSFER PUMP
NOTE: A defective fuel transfer pump may cause low power, hard
starting and White smoke. Check fuel transfer pump output
pressure (cranking and starting), pressure drop and fuel
supply.
Fuel Transfer Pump Preliminary Inspection
1) Check for restricted or leaking fuel supply line to fuel
transfer pump or fuel return line located on driver's side of engine.
See Fig. 1 . Repair fuel supply line or fuel return line if restricted
or leaking.
2) Check for fuel leaking from fuel transfer pump. Replace
fuel transfer pump if fuel is leaking. Check fuel transfer pump output
pressure.
Fuel Transfer Pump Output Pressure
1) Clean area around filter fitting plugs, then remove plugs.
See Fig. 7 . Install Test Fittings (AVU1-2). Install Fuel Pressure Test
Gauge (6828) at inlet port. See Fig. 7. To prevent engine starting,
remove fuel injection pump relay, located in power distribution
center.
2) Turn ignition switch to START position. Inlet pressure
should be 5-7 psi. Install fuel injection pump relay. Start engine.
Inlet pressure should be 10 psi. Using a scan tool, clear FTC. FTC may
set when relay is removed. Check pressure drop.
Fig. 7: Checking Fuel Transfer Pump Output Pressure
Courtesy of Chrysler Corp.
Pressure Drop Test
Turn engine off. Move pressure gauge from inlet port to

BO DY C O NTR O L C O M PU TE R

1999 D odge P ic ku p R 1500
1999 ACCESSORIES & EQUIPMENT
CHRY - Body Control Computer Tests
Ram Pickup
NOTE: See BODY CONTROL COMPUTER - INTRODUCTION article before
proceeding with following test. Body control computer in RWD
trucks is the Central Timer Module (CTM).
SYMPTOM IDENTIFICATION
IDENTIFYING VEHICLE EQUIPMENT & SYSTEM PROBLEMS
NOTE: For connector terminal identification wiring diagrams, see
BODY CONTROL COMPUTER - INTRODUCTION article.
NOTE: Perform a visual inspection before proceeding with this test.
Ensure battery is fully charged.
1) Connect scan tool to Data Link Connector (DLC). DLC is a
16-pin connector located under left side of dash, to left of steering
wheel. Turn ignition switch to ON position. If scan tool display is
not blank, go to next step. If scan tool display is blank, see
appropriate VEHICLE COMMUNICATIONS article.
2) Using scan tool, select SYSTEM MONITORS, then CCD BUS
TEST. Scan tool will perform a CCD bus test. If scan tool displays BUS
OPERATIONAL, go to next step. If scan tool displays any message except
BUS OPERATIONAL, see appropriate VEHICLE COMMUNICATIONS article.
3) Using scan tool, select READ DTCs. If any Diagnostic
Trouble Codes (fault messages) are present, go to appropriate fault
message. If no fault messages are present, identify customer
complaint. See following list for possible fault messages and customer
complaint symptoms. Problems listed are diagnosed using a scan tool.
These problems may occur separately or in various combinations. When
diagnosing a system with many apparent problems, a sequence of tests
may be required. After repairs, ensure problem(s) or failure(s) have\
been corrected.
CHIME SYSTEM
* CHIME INOPERATIVE - ENGINE TEMPERATURE CRITICAL
* CHIME INOPERATIVE - KEY IN IGNITION & LF DOOR OPEN
* CHIME INOPERATIVE AT ALL TIMES
* CHIME INOPERATIVE WITH EXTERIOR LIGHTS ON
* CHIME INOPERATIVE WITH LOW OIL PRESSURE
* CHIME INOPERATIVE WITH DRIVER DOOR OPEN
DOOR AJAR SYSTEM
* OPEN LEFT DOOR AJAR CIRCUIT
* OPEN RIGHT DOOR AJAR CIRCUIT
* SHORTED LEFT DOOR AJAR CIRCUIT
* SHORTED RIGHT DOOR AJAR CIRCUIT
INSTRUMENT CLUSTER
* ALL GAUGES INOPERATIVE
* ANY CCD CLUSTER WARNING LIGHT INOPERATIVE
* ANY HARD WIRED CLUSTER WARNING LIGHT INOPERATIVE

PCM INACTIVE ON BUS, go to appropriate VEHICLE COMMUNICATIONS article.
If scan tool does not display PCM INACTIVE ON BUS, go to next step.
4) Turn ignition off. Remove instrument cluster. See
appropriate INSTRUMENT PANELS article. Turn ignition on. Using
external voltmeter, measure voltage between ground and instrument
cluster connector C1 terminal No. 6 (Yellow wire). If voltage is 10
volts or less, repair open Yellow wire. If voltage is more than 10
volts, replace instrument cluster.
ANY CCD CLUSTER LIGHT INOPERATIVE
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
1) Turn ignition on. Using scan tool, select ELECTRO/MECH
CLUSTER. If scan tool displays BUS OPERATIONAL, go to next step. If
scan tool does not display BUS OPERATIONAL, go to appropriate VEHICLE
COMMUNICATIONS article and follow appropriate symptom diagnostics.
2) If scan tool displays NO RESPONSE, go to appropriate
VEHICLE COMMUNICATIONS article. If scan tool does not display NO
RESPONSE, go to next step.
3) Using scan tool, select SYSTEM TEST. If scan tool displays
PCM INACTIVE ON BUS, go to appropriate VEHICLE COMMUNICATIONS article.
If scan tool does not display PCM INACTIVE ON BUS, go to next step.
4) Push and hold RESET button while cycling ignition key.
Release RESET button when CHEC appears in odometer display. Observe
inoperative light during self-test. If inoperative light did not
illuminate during self-test, go to next step. If inoperative light
illuminated during self-test, verify if light is controlled by an
input to instrument cluster. See appropriate wiring diagram in BODY
CONTROL COMPUTER - INTRODUCTION article. If light is controlled by an
input to instrument cluster, go to appropriate circuits article or
symptom test. See IDENTIFYING VEHICLE EQUIPMENT & SYSTEM PROBLEMS. If
light is not controlled by an input to instrument cluster, system is
currently functioning correctly.
5) Gain access to instrument cluster. See appropriate
INSTRUMENT PANELS article. If defective light is a LED, replace
instrument cluster. If defective light is a bulb, go to next step.
6) Remove and inspect defective bulb. If bulb is burned out,
replace bulb. If bulb is not burned out, replace instrument cluster.
ANY HARD WIRED CLUSTER WARNING LIGHT INOPERATIVE
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
1) Remove instrument cluster. See appropriate INSTRUMENT
PANELS article. Remove inoperative bulb. If bulb is burned out,
replace bulb. If bulb is not burned out, go to next step.
2) Inspect wiring diagram and evaluate which instrument
cluster provides; power or ground for inoperative bulb. See
appropriate wiring diagram in BODY CONTROL COMPUTER - INTRODUCTION
article. Using external ohmmeter or voltmeter, check appropriate power
or ground circuit. If circuit is okay, replace instrument cluster. If
power or ground is not available at appropriate circuit, repair open

multiple engine sensors have failed, repair ground between splice and
PCM.
12) Connect jumper wire between OPS connector terminals. If
oil pressure warning indicator illuminates, replace OPS. If oil
pressure warning indicator does not illuminate, go to next step.
13) Do not remove jumper wire. Disconnect PCM Black connector
C2. PCM is located in engine compartment on right inner fender. Using
an external ohmmeter, measure resistance between ground and PCM White
connector C2 terminal No. 23 (Gray/Orange wire). If resistance is less\
than 5 ohms, replace PCM. If resistance is 5 ohms or more, repair open
Gray/Orange wire.
14) Check cooling system operation. If cooling system is
operating properly, go to next step. If cooling system is not
operating properly, repair engine cooling problem.
15) Using scan tool, select PCM MONITOR under SYSTEM TESTS.
If scan tool displays PCM ACTIVE ON BUS, system is currently
functioning properly. If scan tool does not display PCM ACTIVE ON BUS,
go to appropriate VEHICLE COMMUNICATIONS article.
16) Using scan tool, select MODULE ENGINE CONTROLLER. Read
PCM DTCs. If scan tool displays any charging system related DTCs, go
to appropriate SELF-DIAGNOSTICS article in ENGINE PERFORMANCE section
and repair DTC as necessary. If scan tool does not display any
charging system related DTCs, go to next step.
17) Check charging system operation. If charging system is
operating properly, replace instrument cluster. If charging system is
not operating properly, repair engine charging problem.
18) Using scan tool, select BODY COMPUTER MONITORS. Read CCD
BUS ENGINE INFO. If scan tool displays engine RPM, replace instrument
cluster. If scan tool does not display engine RPM, replace PCM.
OVERHEAD CONSOLE CONCERNS
AVERAGE MPH/FUEL ECON INOPERATIVE OR WRONG (CMTC FAILS TO
RESPOND TO INSTRUMENT CLUSTER DIMMING, DISTANCE TO EMPTY
INOPERATIVE OR WRONG, ELAPSED TIME INOPERATIVE/WRONG, SWITCH
ON CMTC INOPERATIVE, TRIP ODOMETER INOPERATIVE/WRONG)
NOTE: If any listed symptoms exist, Compass Mini-Trip computer
(CMTC) is defective. Replace CMTC. Perform VERIFICATION TEST
VER- 1A after each repair.
CMTC SHOWS FAILED
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
Using scan tool, perform AUTO SELF TEST. If CMTC shows
failed, replace CMTC. If CMTC does not show failed, system is
currently functioning properly.
CMTC SEGMENTS FAIL TO LIGHT UP
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
Using scan tool, perform AUTO SELF TEST. If CMTC segments
fail to illuminate, replace CMTC. If CMTC segments all illuminate
properly, system is currently functioning properly.
INCORRECT READING BEYOND +/- 5

1) Start engine, and check booster vacuum hose connections. A
hissing noise indicates a vacuum leak. Repair any vacuum leaks before
proceeding. Stop engine, and shift transmission into Neutral. Pump
brake pedal until all vacuum reserve in booster is depleted.
2) Hold brake pedal under light pressure. If pedal does not
hold firm and falls away, master cylinder may be faulty. Bleed system
using appropriate method, and repeat step 1). See BLEEDING PROCEDURES
under BLEEDING BRAKE SYSTEM.
3) If pedal still does not hold firm, master cylinder is
faulty. If pedal holds firm, start engine and observe pedal height. If
pedal height change is not apparent, power booster or vacuum check
valve is faulty. Install good check valve, and repeat steps 1) and 2).\
If pedal falls away slightly under light pressure and then holds firm,
go to next step .
4) Start engine. Release brake pedal. Increase engine speed
to 1500 RPM. Close throttle and immediately turn off ignition. Wait at
least 90 seconds, and try brake action again. Booster should provide 2
or more vacuum assisted pedal applications. If vacuum assist is not
provided, perform booster and check valve vacuum tests.
POWER BRAKE BOOSTER VACUUM TEST
Connect vacuum gauge to booster check valve using "T"
fitting. Start engine, and run at idle speed for one minute. Clamp
hose shut between vacuum source and check valve. Stop engine, and
observe vacuum gauge. If vacuum drops more than one in. Hg within 15
seconds, booster diaphragm or check valve is faulty.
POWER BRAKE BOOSTER CHECK VALVE TEST
Disconnect vacuum hose from check valve. Remove check valve
and valve seal from booster. Use a hand-operated vacuum pump for
testing. Apply 15-20 in. Hg at large end of check valve. Vacuum should
hold steady. If gauge on pump indicates vacuum loss, check valve is
faulty and should be replaced.
COMBINATION VALVE METERING VALVE TEST
Metering valve operation can be checked visually with aid of
an assistant. While an assistant applies and releases brake pedal,
observe metering valve stem. If valve is operating correctly, stem
will extend slightly when brakes are applied, and contract when brakes
are released. If valve is faulty, replace combination valve assembly.
COMBINATION VALVE PRESSURE DIFFERENTIAL SWITCH TEST
1) Using an assistant, apply brake pedal. Observe brake
warning light. Raise and support vehicle, and connect a bleed hose to
one rear wheel cylinder. Submerge other end of hose into container
partially filled with brake fluid. Have assistant press and hold brake
pedal down while observing brake warning light. Open bleeder screw. If
warning light glows, switch is operating properly.
2) If warning light fails to glow, check circuit fuse, bulb
and wiring. Repair as necessary. Repeat step 1). If warning light
fails to glow, check brakelight, parking brake switches and related
wiring. Repair as necessary. Repeat step 1). If warning light fails to
glow, pressure differential switch is faulty. Replace combination
valve assembly, and bleed brake system. Verify proper valve operation.
REMOVAL & INSTALLATION