1999 CHEVROLET TRACKER instrument panel

Second Printing for Chevrolet Tracker Owner's Manual ± 1999
yellowblue
2-12
LOCK (A): This is the only position in which you can
remove the key. This locks your steering wheel, ignition
and automatic transmission.
If you have an automatic transmission, the ignition
switch can't be turned to LOCK unless the shift lever is
in PARK (P).
ACC (ACCESSORY) (B): This is the position in which
you can operate your electrical power accessories. It
unlocks the steering wheel and ignition. Use this
position if your vehicle must be pushed or towed.
ON (C): This is the position that the switch returns to
after you start your engine and release the switch. The
switch stays in the ON position when the engine is
running. But even when the engine is not running, you
can use ON to operate your electrical power accessories
and to display some instrument panel warning and
indicator lights.
START (D): This is the position that starts the engine.
When the engine starts, release the key. The ignition
switch will return to ON for normal driving.
When the engine is not running, ACC and ON allow you
to operate your electrical accessories, such as the radio.
A warning tone will sound if you open the driver's door
when the ignition is in ACC or LOCK and the key is in
the ignition.
CAUTION:
On manual transmission vehicles, turning the key
to LOCK will lock the steering column and result
in a loss of ability to steer the vehicle. This could
cause a collision. If you need to turn the engine
off while the vehicle is moving, turn the key only
to ACC. Don't push the key in while the vehicle
is moving.
NOTICE:
If your key seems stuck in LOCK and you can't
turn it, be sure you are using the correct key; if
so, is it all the way in? If it is, then turn the
steering wheel left and right while you turn the
key hard. But turn the key only with your hand.
Using a tool to force it could break the key or the
ignition switch. If none of this works, then your
vehicle needs service.

Second Printing for Chevrolet Tracker Owner's Manual ± 1999
yellowblue
2-18 Overdrive Off Switch (If Equipped)
JE±12±0007±X
The Overdrive Off switch is located on the left side of
the shifter. By operating the Overdrive Off switch, the
four
-speed automatic transmission (three-speed plus
overdrive) can be converted to a three
-speed automatic
transmission. While in the three
-speed mode, the
transmission will not shift into the Overdrive position.
To convert the transmission to the three
-speed mode,
push in the Overdrive Off switch and release it. The
switch comes out and the OD/OFF indicator light on the
instrument panel comes on.To return the transmission to the four
-speed mode, push
in the Overdrive Off switch again. The switch will
remain in and the OD/OFF indicator light goes off.
Please note that if the transfer case shift lever is in the
4L position, the four
-speed automatic transmission will
remain in the three
-speed mode.
Power Mode Selector Switch
JE±12±0006±X
A power mode
selector switch is included
with the four
-speed
automatic transmission.
When you need more power for climbing hills or
quicker acceleration, press the P (POWER) switch. The
POWER indicator light on the instrument panel comes
on. For normal driving, press the N (NORMAL) switch.
The POWER indicator light goes off.

Second Printing for Chevrolet Tracker Owner's Manual ± 1999
yellowblue
2-31 Turn Signal and Lane Change Indicator
The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow you
to signal a turn or a lane change.
To signal a turn, move the lever all the way up or down.
When the turn is finished, the lever will return automatically.
X±02±1321±T
An arrow on the instrument
panel will flash in the
direction of the turn or
lane change.
To signal a lane change, just raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete your lane change. The lever will return by
itself when you release it.
As you signal a turn or a lane change, if the arrows don't
flash but just stay on, a signal bulb may be burned out
and other drivers won't see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows don't go on at all when you
signal a turn, check the fuse (see ªFuses and Circuit
Breakersº in the Index) and for burned
-out bulbs.
Headlamp High/Low Beam Changer
First, you must have the headlamps on. For high beams,
push the turn signal lever toward the instrument panel.
X±02±3323±T
When the high beams are
on, a light on the instrument
panel also will be on. It will
go off when you switch to
low beam.
To switch back to low beams, pull the lever toward you.
Flash-to-Pass
With the lever in the low-beam position, pull the lever
toward you to momentarily switch to high beam (to
signal that you are going to pass). When you release the
lever, the headlamps will return to low
-beam operation.

Second Printing for Chevrolet Tracker Owner's Manual ± 1999
yellowblue
2-35
JE±12±0014±X
1. Press the CRUISE
CTRL. switch on the
instrument panel to turn
the system on. The
indicator light on the
switch will come on.
2. Get up to the speed you want.
3. Once you're going 25 mph (40 km/h) or more, turn
the lever to COAST SET and release. Your cruise
will set.
4. Take your foot off the accelerator pedal.
Resuming a Set Speed
If you set your cruise control at a desired speed and then
apply the brake, this will turn off the cruise control
function. But you don't need to reset it.
Once you're going about 25 mph (40 km/h) or more,
you can turn the lever to RESUME ACCEL for about
one second. You'll go right back to your chosen speed
and stay there.Increasing Speed While Using Cruise Control
There are two ways to go to a higher speed.

Use the accelerator pedal to go to a higher speed.
Turn the lever to COAST SET and release. Take
your foot off the accelerator pedal. You'll now cruise
at the higher speed.

Turn the lever to RESUME ACCEL. Hold the lever
at RESUME ACCEL until you get up to the speed
you want, then release the lever.
Reducing Speed While Using Cruise Control
To reduce your speed, turn and hold the lever in the
COAST SET position until you reach the lower speed
you want, then release the lever.
Passing Another Vehicle While Using Cruise Control
Use the accelerator pedal to increase your speed. When
you take your foot off the pedal, your vehicle will slow
down to the cruise control speed you set earlier.

Second Printing for Chevrolet Tracker Owner's Manual ± 1999
yellowblue
2-36
Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and the steepness of the hills.
When going up steep hills, you may have to step on the
accelerator pedal to maintain your speed. When going
downhill, you may have to brake or shift to a lower gear
to keep your speed down. Of course, applying the brake
takes you out of cruise control. Many drivers find this to
be too much trouble and don't use cruise control on
steep hills.
Getting Out of Cruise Control
There are three ways to turn off cruise control:

Step lightly on the brake pedal, or push the clutch
pedal if you have a manual transmission.

Push in the CANCEL button on the end of the cruise
control lever.

Press the CRUISE CTRL. switch on the
instrument panel.
Erasing Speed Memory
When you turn off the cruise control or the ignition,
your cruise control set speed memory is erased.Exterior Lamps
JE±12±0031±X
Turn the outside part of the lever to control the lamps.
There are three positions for the lamp switch.

Second Printing for Chevrolet Tracker Owner's Manual ± 1999
yellowblue
2-37 Parking Lamps
: This position will turn on the following:

Parking Lamps

Sidemarker Lamps

Taillamps

Instrument Panel Lights

License Plate Lamp
Headlamps
: This position will turn on the following:

Headlamps

Parking Lamps

Sidemarker Lamps

Taillamps

Instrument Panel Lights

License Plate Lamp
Turn the switch to OFF to turn off the lamps.
Daytime Running Lamps
Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during the day.
DRL can be helpful in many different driving
conditions, but they can be especially helpful in the
short periods after dawn and before sunset.
The DRL system will make your headlamps come on at
a reduced brightness when:

The ignition is on with the engine running,

the headlamp switch is off or the parking lights are
on and

the parking brake is released.
When the DRL are on, only your headlamps will be on
at a reduce brightness. The taillamps, sidemarker and
other lamps won't be on. Your instrument panel won't
be lit up either.
When you turn on the headlamp switch, your DRL will
go off and your headlamps will come on. The other
lamps that come on with your headlamps will also
come on.

Second Printing for Chevrolet Tracker Owner's Manual ± 1999
yellowblue
2-38
When it begins to get dark, the headlamps will
automatically switch from DRL to the regular
headlamps. See ªAutomatic Light Controlº earlier in
this section.
When you turn the headlamp switch to off, the regular
lamps will go off and your headlamps will change to the
reduced brightness of DRL provided it is not dark
outside. DRL also comes on if only the parking lamps
are being used.
To idle your vehicle with the DRL off, set the parking
brake. The DRL will stay off until you release the
parking brake.
As with any vehicle, you should turn on the regular
headlamp system when you need it.
Automatic Light Control (ALC)
Your vehicle is equipped with an automatic light sensor
on top of the instrument panel, so be sure it is not
covered which will cause the nighttime lights to be
on continuously.When it is dark enough outside, your ALC will turn on
your low
-beam headlamps at the normal brightness
along with other lamps such as the taillamps,
sidemarker, park lamps and instrument panel lights.
There is a short delay in the transition between daytime
and nighttime operation of the Daytime Running Lamps
(DRL) and the ALC systems. If the light sensor senses a
reduction in lighting that lasts longer than 20 seconds, it
will activate the nighttime lamps. If you are driving
through a parking garage, heavy overcast weather or a
tunnel, the ALC will turn on your low
-beam headlamps
at a normal brightness along with the taillamps,
sidemarker, park lamps and the instrument panel lights.
The radio lights will be dimmer.
As with any vehicle, you should turn on the regular
headlamp system when you need it.
Lamps On Reminder
If you turn the ignition off, remove the key, open the
door and leave the lamps on, a tone will remind you to
turn off your lamps.

Second Printing for Chevrolet Tracker Owner's Manual ± 1999
yellowblue
2-39
Interior Lamps
Instrument Panel Brightness Control
JE±12±0015±X
The thumbwheel controls
the brightness of your
instrument panel lights.
Rotate the wheel upward to
brighten the lights or
downward to dim them.
Dome Lamp
The dome lamp has a three-position switch.
OFF: This position is to the left when you are sitting in
the driver's seat. The lamp stays off even when a door
is open.
Center: This is the center position. The lamp comes on
when a door is opened.
ON: This position is to the right when you are sitting in
the driver's seat. The dome lamp turns on and stays on
whether or not a door is open.
Battery Rundown Protection
Your vehicle is equipped with a battery saver feature
designed to protect your vehicle's battery.
When the dome lamp is left on and the ignition is turned
off and the key is removed, the battery saver system will
automatically turn the lamp off after about 15 minutes.
This will avoid draining the battery. This system does
not protect against leaving on the headlamps or
parking lamps.