1999 CHEVROLET ASTRO PASSENGER lock

yellowblue
v
For example,
these symbols
are used on an
original battery:
CAUTION
POSSIBLE
INJURY
PROTECT
EYES BY
SHIELDING
CAUSTIC
BATTERY
ACID COULD
CAUSE
BURNS
AVOID
SPARKS OR
FLAMES
SPARK OR
FLAME
COULD
EXPLODE
BATTERY
These symbols
are important
for you and
your passengers
whenever your
vehicle is
driven:
DOOR LOCK
UNLOCK
FASTEN
SEAT
BELTS
POWER
WINDOW
AIR BAG
These symbols
have to do with
your lamps:
MASTER
LIGHTING
SWITCH
TURN
SIGNALS
PARKING
LAMPS
HAZARD
WARNING
FLASHER
DAYTIME
RUNNING
LAMPS
FOG LAMPS
These symbols
are on some of
your controls:
WINDSHIELD
WIPER
WINDSHIELD
WASHER
WINDSHIELD
DEFROSTER
REAR
WINDOW
DEFOGGER
VENTILATING
FAN
These symbols
are used on
warning and
indicator lights:
ENGINE
COOLANT
TEMP
BATTERY
CHARGING
SYSTEM
BRAKE
COOLANT
ENGINE OIL
PRESSURE
ANTI-LOCK
BRAKES
Here are some
other symbols
you may see:
FUSE
LIGHTER
HORN
SPEAKER
FUEL
Vehicle Symbols
These are some of the symbols you may find on your vehicle.

yellowblue
1-2
Seats and Seat Controls
This section tells you about the seats -- how to adjust
them, take them out and put them back in. It also tells
you about bucket and bench seats, power seats and
head restraints.
Manual Front Seats
CAUTION:
You can lose control of the vehicle if you try to
adjust a manual driver's seat while the vehicle is
moving. The sudden movement could startle and
confuse you, or make you push a pedal when you
don't want to. Adjust the driver's seat only when
the vehicle is not moving.
2-Way Front Seat
The bucket seats can be
adjusted forward or
rearward by the lever
at the front of the seat.
Move the seat adjustment lever at the front of the seat
toward the driver's door to unlock it. Slide the seat to
where you want it. Then release the lever and try to
move the seat with your body, to make sure the seat is
locked into place.

yellowblue
1-4 Reclining Seatbacks
There is a lever on the inside of the seat to adjust
the seatback.
You can adjust the seatback
by lifting the lever and
leaning back. Release the
lever to lock the seatback
where you want it. Pull up
on the lever, lean forward
and the seat will go to an
upright position.
But don't have a seatback reclined if your vehicle
is moving.

yellowblue
1-6
To fold your non-touring
bench seatback forward,
pull up on the latch release
lever while pulling the
seatback toward the rear of
the vehicle.
After the latch has been released, push the seatback
toward the front of the vehicle until it locks in place. To
raise the seatback, unlock the seatback latch by pushing
up on the lever while pushing down on the upper edge
of the seatback. Move the seatback into the upright
position. Make sure the seatback is locked when it is
back in the upright position.
CAUTION:
If the seatback isn't locked, it could move forward
in a sudden stop or crash. That could cause injury
to the person sitting there. Always press rearward
on the seatback to be sure it is locked.
Rear Seats
Bucket Seats
You may have rear bucket seats with an adjustment
release bar at the front of the seats. These seats can be
adjusted forward or rearward with the release bar. Pull
the release bar up to release the seat bottom and slide the
seat where you want it. Then let go of the release bar
and try to move the seat with your body, to make sure
the seat is locked into place.

yellowblue
1-7
Bench Seats
If you have bench seats in your vehicle, each seat can
carry up to three passengers. They can also be removed
to increase storage space.
The center bench and rear bench seats can be adjusted
forward or rearward by the lever at the front of the seat.
Move the seat adjustment
lever at the front of the seat
toward the passenger's side
to unlock it. Slide the seat to
where you want it. Then
release the lever and try to
move the seat with your
body, to make sure the seat
is locked into place.
The non
-touring center bench seat has a pivoting
right armrest. The left armrest can also be used as a
storage compartment.
The optional touring bench seats come with moveable
armrests, individual reclining seatbacks, adjustable
headrests and a fold
-down center armrest console.
To adjust your seatback, pull up on the lever on the
lower outside of the seat.
The center bench seatbacks will recline further back
than the rear bench seatbacks.

yellowblue
1-8
To raise or lower the center
console, press the button
between the beverage
holders. Sit in the center
seating position only when
the console is in an upright
and locked position.
For details about headrests, see ªHead Restraintsº in
this section.Removing the Rear Seats
To remove the rear seats, do the following:
1. If you are removing the
center seat, remove the
right lap
-shoulder belt.
To do this, press the tip
of a key into the release
hole of the safety belt
attachment while pulling
up on the safety belt.

yellowblue
1-9
2. If you have a safety belt
guide on your seat, pull
the safety belt all the
way out through
the guide.
3. To store the safety belt
while the second row
seat is removed, pull the
belt out and put both
buckles in the
passenger's side rear
storage bin.
Route the belt out of the forward edge of the storage bin.
Close the cover to retain the belt.
4. Pull up on the seatback latch on the right rear of the
seat. Push the seatback down until it locks in place
(non
-touring bench seats only).
5. Lift up on the left and the right seat release levers at
the same time. The latches are near the floor on the
rear legs of the seat.

yellowblue
1-11
2. Pull the seat down to latch the rear retainers. Make
sure the seat is locked in by pulling up and down on
the seat.
CAUTION:
A seat that isn't locked into place properly can
move around in a collision or sudden stop. People
in the vehicle could be injured. Be sure to lock
the seat into place properly when installing it.
3. To raise the seatback on vehicles equipped with the
non
-touring seat, unlock the seatback latch by
pushing up on the latch release lever at the right rear
of the seat, while pushing down on the upper edge of
the seatback. Move the seatback into the upright
position. Make sure the seatback is locked when it is
back in the upright position.
4. If you are replacing the center seat, connect the right
lap
-shoulder belt to the attachment on the seat
cushion. If you have a safety belt guide on your seat,
pull the belt through the guide before reattaching the
lap
-shoulder belt to the side of the seat. The release
hole should be facing outward.
If you installed the safety belt with the release hole
facing inward (toward the seat), slide the plastic
cover up so you can see the buckle. Disconnect the
seat belt. Slide the cover back down and reinstall the
belt correctly.