1999 BMW 528i exhaust

Downloaded from www.Manualslib.com manuals search engine
I_
-.
Cylinder Head and Valvetrain
Remove torx
(arrows). screws
from
exhausl
: camshaft : sprocket
Lift off exhaust and intalte sprockets together with secondary
chain, thrust spacer
(A) from exhaust camshaft, and splined
shaft (B) from intake camshaft.
CAUTIOf+
Splined shafts share the same part number for both intake
and exhaust camshafts. Used splined shafts must be rein-
stalled in their
oriqinal locations.
Place intalte and exhaust sprockets in
BMW special tool 11 6
/ 180. Position spline gap on intake sprocket (arrow) as
shown.
4 Remove exhaust camshaft splined sleeve (A) and shaft (B).

Downloaded from www.Manualslib.com manuals search engine
11 6-22
Cylinder Head and Valvetrain
Remove secondary chain tensioner mounting bolts (arrows)
and remove tensioner with locking tool in place.
Remove primary chain sprocket mounting studs
(arrows) on
exhaust camshaft.
NOTE-
Counterhold camshafts when loosening.
Lifl primary chain sprocket off exhaust camshaft. Remove
sprocket from chain.

Downloaded from www.Manualslib.com manuals search engine
11 6-23
Cylinder Head and Valvetrain
Place timing
chain on end of exhaust camshaft
4 Do not remove end spline retaining screws from camshafts
(arrows).
CAUTION-
The end spline retaining screws precisely locate the end
splines to the camshafts. Do not loosen these screws.
Remove locating studs (arrows) from
intake camshaft. Lift
off intake
camshaft thrust spacer (A) and impulse wheel (B)
4 Remove cylinder head cover mounting studs (arrows) from
center of cylinder head.
- Remove crankshaft locking tool (BMW special tool 11 2 300)
from cranltcase.

Downloaded from www.Manualslib.com manuals search engine
Cylinder Head and Valvetrain
NOTE-
The camshaft bearing caps are coded with a letter and a
number. For example, "A
1" is the first exhaust camshaft
bearing cap
at the front of the engine, and "El "is the intake
camshaft bearing cap at the front of the engine.
-. -
The camshafts are stamped with a code letter - "E for the
intake side and
'X" for the exhaust side.
"E is for Einlap. (German for intake) and 'XA7s for Auspuff.
(German for exhaust).
- Repeat procedure for exhaust camshaft
< Secure hydraulic lifters in lifter bores using BMW special tool
11 3 250, or remove lifters using a magnetic pick-up tool.
I CAUTION-
Used liydraulic lifters must be reinstalled in original lifter
1 bores.
4 Remove lower camshaft bearing carriers from cylinder head.
CAUTION- Camshaft bearing carriers must be reinstalled in their original
locations
(E for intalce and A for exhaust).
NOTE- Do not allow hydraulic lifters to fall out of camshaft carriers.
Hydraulic lifters should be stored in an upright position.
Camshafts and lifters, installing (M52TU and M54 engine)
Lubricate camshafts, camshaft carriers, bearing caps, hy-
draulic lifters, friction washers, splined shafts and
spline hubs
with assembly
lubricant before installation.
CAUTION-
Make sure the crankshaft, which had been rotated approxi-
mately
30" opposite the direction of engine rotation from
TDC, is
stillin thatposition before lowering the camshafts into
position. Allpistons must be out of
TDCposition to prevent
valve/piston inteiference when the carnshafis are installed.
- Lift timing chain and place exhaust cam onto exhaust cam-
shaft carriers. Place
intake camshaft on camshaft carrier.

Downloaded from www.Manualslib.com manuals search engine
11 6-26
I Cylinder Head and Valvetrain
4 Before installing camshaft carriers, examine bearing bores
(arrows) on hydraulic lifter bores for signs of wear.
Install camshaft carriers with hydraulic lifters into cylinder
head. Note marks on carriers:
(E) for intake side and (A) for
exhaust side.
4 Center camshaft carrier on pins (arrows) at bearing
aositions 2 and 7.

Downloaded from www.Manualslib.com manuals search engine
-- - . .- -,
Cylinder Head and Valvetrain
4 Rotate camshafts so that intalte and exhaust lobes for cylin-
der
1 face each other (arrows).
CAUJION-
A minimum waiting time is required for the hydraulic lifters to
'bleed down"after installing the camshafts into the cylinder
head, before bringing the piston to TDC. When the camshafts
are removed, the hydraulic lifters can expand. This expan-
sion can cause increased valve lift when the camshafts are
bolted down, possibly resulting in piston interference.
Place bearing caps on cams, but do not install retaining nuts.
4 Fit BMW special tool 11 3 260 (A) and 11 3 270 (B) to cylinder
head over
intalte camshaft and screw long bolts (arrows)
into spark plug threads.
CA UTION-
Do not overtighten bolts into spark plug holes.
< Turn eccentric shaft of special tool to pretension bearing
caps. Install and torque nuts on intake camshaft bearing
caps.
Tightening torque Camshaft bearing cap
to cylinder head (M7) 14 Nm (10 it-ib)
- Release tension on eccentric shaft and remove BMW special
tools
11 3 2601270.
- Repeat procedure for exhaust camshaft.
NOTE-
Observe waiting time for lifter bleed down before continuing
with camshaff installation.
Crankshaft
I valve timing waiting times
68°F (20°C) and higher 5 minutes
50-6S°F(10-20°C) 15 minutes
32-50DF(O-10°C) 30 minutes

Downloaded from www.Manualslib.com manuals search engine
11 6-28
Cylinder Head and Valvetrain
Double
VANOS timing
chain components
1. Impulse wheel mounting nut
2. Exhaust camshaft impulse
wheel
3. Spring plate, exhaust
4. Thrust spacer (T
= 3.5 mm)
5. Splined shaft
6. Torx screw
7. Exhaust camshaft secondary
sprocket
8. Secondary timing chain
9. Splined sleeve
10. Primary sprocket
11. Threaded stud
12. Secondary chain tensioner
13. Secondary chain lower guide
14. Sprocket mounting nut
15. Spring plate, intake
16. Splined shaft
17. Intake camshaft sprocket
18. Locating stud
19. Thrust spacer
20. lntake camshaft impulse wheel

Downloaded from www.Manualslib.com manuals search engine
11 6-31
Cylinder Head and Valvetrain
< Install primary timing chain on timing chain sprocket and
place on exhaust camshaft so that pointer on sprocket
(arrow) lines up with cylinder head sealing surface.
4 Insert BMW special tool 11 4 220 into timing chain tensioner
bore and bring center spindle into contact with tensioning rail.
Tighten until slack is removed, but do not pretension timing
chain.
NOTE-
BMW special tool 11 4 220 is an adjustable primary chain
tensioner and simulates the function of the tensioner.
- Recheck arrow on primary sprocket is aligned with upper
edge of cylinder head. Reposition sprocket if necessary.
4 Insert and tighten threaded locat~ng studs (arrows) in ex-
haust camshaft.
Tightening
torques
Exhaust camshaft locating stud 20 Nm (15 ft-lb)