Page 3 of 8
27-42
Note:
Before removing the ribbed belt, mark the direction of travel with chalk or
a felt tipped marker. Reversing the direction of travel of an used belt can
destroy it. When installing the belt, make sure it is correctly seated in the
belt pulleys. - Loosen mounting bolts for air conditioning compressor belt tensioner
(arrows).
- Release tension on ribbed belt and remove.
- Unbolt air conditioning compressor.
Tightening torque: 25 Nm (18 ft lb)
- Hang air conditioning compressor up on chassis with its refrigerant
lines attached.
Pa
ge 3 of 8 Starter, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.27.3
Page 4 of 8
27-43
- Disconnect wire from terminal 30/B+ by removing nut -2-.
Tightening torque: 16 Nm (12 ft lb)
- Disconnect harness connector -1- from terminal 50.
- Remove bolt -3-.
Tightening torque: 22 Nm (16 ft lb)
- Unbolt wiring clamp -4-.
Tightening torque: 4 Nm (35 in. lb)
- Remove starter mounting bolts -1- and -2-.
Tightening torque: 65 Nm (48 ft lb)
- Remove starter toward front.
Pa
ge 4 of 8 Starter, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.27.3
Page 5 of 8
27-44
Installing
Installation is the reverse of removal; noting the
following:
Vehicles with air conditioning
- Install ribbed belt for air conditioning
compressor.
All vehicles - Place torque wrench on hex head of belt tensioner as shown and
tighten to 25 Nm (18 ft lb).
- Maintain torque on belt tensioner and tighten bolt -A- to 20 Nm (15 ft
lb).
- Start engine and make sure belt runs properly.
Pa
ge 5 of 8 Starter, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.27.3
Page 6 of 8
27-45
Vehicles with 6-cylinder gasoline
engines
Removing
Note:
To remove the starter, it is first necessary to
remove the generator Page 27
-26
.
2.7 L/184 kW engine, 5V twin-turbo only
All vehicles - Remove air duct -1-.
2 - Attachment point for oil and refrigerant lines
3 - Engine block mounting point
4 - Hose clamp (loosen)
- Disconnect wire from terminal 30/B+ -2- by removing nut. Tightening
torque: 16 Nm (12 ft lb)
- Disconnect harness connector from terminal 50 -2-.
Pa
ge 6 of 8 Starter, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.27.3
Page 7 of 8
27-46
Vehicles with manual transmission
- Remove rear noise insulation panel (arrows).
- Remove mounting bolts -1- and -2- for starter.
Tightening torque: 65 Nm (48 ft lb)
- Remove starter toward front.
Pa
ge 7 of 8 Starter, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.27.3
Page 8 of 8
27-47
Vehicles with automatic transmission
- Remove right-front wheel.
Installing - Upper bolt -1- can be unscrewed from right-front wheel housing.
Tightening torque: 65 Nm (48 ft lb)
- From engine side, remove lower bolt.
Tightening torque: 65 Nm (48 ft lb)
- Remove starter toward front.
- Install starter in reverse order of removal.
Pa
ge 8 of 8 Starter, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.27.3