1999 AUDI A4 lock

01-386

Printed output from
VAG1551 Scan Tool
(ST) Possible cause
Corrective action
DTC
01203
ABS / instrument
cluster electrical
connection
No signal

Continuation:
Note: Only replace the control
module as a last resort.
A/C control module -J301-
malfunctioning. - If the TIM signal is also not recognized by the A/C control
module -J301-, disconnect the A/C control module -J301- and
check the TIM signal by reading the measuring value blocks for
the ABS control module.
- "Read measuring value block" function 08 page 01
-256
- If the signal is recognized by the ABS control module -J104-
now, replace the A/C control module -J301-.

Note: Only replace the control
module as a last resort.
Instrument cluster
combinator processor -
J218- malfunctioning. - If the ABS control module -J104- still does not recognize the
TIM signal, replace the instrument cluster combination
processor -J218-.
Pa
ge 32 of 96 Electronic Stabilization Pro
gram
(ESP
) DTC table
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.17

01-403

Printed output from
VAG1551 Scan Tool
(ST) Possible cause
Corrective action
DTC
01423
Continuation:
Note:
Sensor for
transverse
acceleration -G200-
Implausible signal
The input signals received by ABS control module -J104- are analyzed by computing programs and
checked for plausibility. If the sensor for transverse acceleration -G200- fails, the relevant computing
program relies primarily on the steering angle sensor -G85-. If you think there is a problem with the
sensor for transverse acceleration -G200-, check whether the steering angle sensor -G85- is OK.
The steering angle sensor must also be checked.
- While driving straight ahead (v < 20 km/h), check the zero position of the steering angle sensor -
G85-, by selecting "Read measuring value block", function 08 page 01
-256
, display group 5
page 01
-270
.
- Check the sensor for transverse acceleration -G200- as described in the instructions for "Read
measuring value block" function 08 page 01
-270
, display group 5, page 01
-270
.
See continuation on
next page There are four possibilities:
Pa
ge 51 of 96 Electronic Stabilization Pro
gram
(ESP
) DTC table
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.17

01-417
DTC table; DTCs from 01435 to 01542

Printed output from
VAG1551 Scan Tool
(ST) Possible cause
Corrective action
DTC
01435
Sender 1 for brake
booster -G201-
The brake light switch is not adjusted
correctly or is not installed correctly.
Repair Manual, Brake System, Repair Group 45
- Check the installation position of the brake light
switch.
- Check brake light switch -F-, "Read measuring
value block" function 08 page 01
-256
, display
group 2
- Check sensor for brake pressure -G201-, "Read
measuring value block" function 08 page 01
-256
,
display group 5




See continuation on
next page
Open circuit in signal wire of sender
1 for brake booster -G201-.
Short circuit to B+ or Ground (GND)
in signal wire to sender 1 for brake
booster -G201-. Electrical Wiring Diagrams, Troubleshooting &
Component Locations - Check signal line between sensor for brake
pressure -G201- (terminal 2) and ABS control
module -J104- (terminal 68).
Pa
ge 68 of 96 Electronic Stabilization Pro
gram
(ESP
) DTC table
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.17

01-427

Printed output
from VAG1551
Scan Tool (ST) Possible cause
Corrective action
DTC
01542
Sender for
rotation rate -
G202-
Implausible
signal The input signals received by ABS control module -J104- are analyzed by computing programs and
checked for plausibility. If the sender for rotation rate -G202- fails, the relevant computing program relies
primarily on the steering angle sensor -G85- and the sensor for transverse acceleration -G200-. If you
think there is a problem with the sender for rotation rate -G202-, check whether the steering angle
sensor -G85- and sensor for transverse acceleration -G200- are OK. These must also be checked.
- While driving straight ahead (v < 20 km/h), check the zero position of the steering angle sensor -G85-,
by selecting display group 5 in "Read measuring value block", function 08 page 01
-256
.
- Check the sensor for transverse acceleration -G200- as described in the instructions for "Read
measuring value block" function 08 page 01
-270
, display group 5.
See continuation
on next page There are four possibilities:
Pa
ge 79 of 96 Electronic Stabilization Pro
gram
(ESP
) DTC table
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.17

01-436

Printed output from
VAG1551 Scan Tool (ST) Possible cause
Corrective action
DTC WARNING!
This is only valid for control modules with no.: 4B0 907 389
01542
Sender for rotation rate -
G202-
Implausible signal

Continuation:
Fourth:
The zero position of steering angle sensor -G85- is within the specified range, and the zero
position of sensor for transverse acceleration -G200- is within the specified range:

- Check the sender for rotation rate -G202- by selecting the "Read measuring value block"
function 08 page 01
-256
, display group 5,


The yaw sensor -G202- is loose.
Repair Manual, Brake System, Repair Group 45

- Check bolts for yaw sensor -G202-.



See continuation on next
Open circuit in signal wire of sender
for rotation rate -G202-.
Short circuit to B+ or Ground (GND)
in signal wire to sender for rotation
rate -G202-. Electrical Wiring Diagrams, Troubleshooting &
Component Locations - Check signal line between yaw sensor -G202-
(terminal 3) and ABS control module -J104-
(terminal 79).
Pa
ge 88 of 96 Electronic Stabilization Pro
gram
(ESP
) DTC table
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.17

01-439

Printed output from
VAG1551 Scan Tool (ST) Possible cause
Corrective action
DTC WARNING!
This is only valid for control modules with no.: 8D0 907 389, 8D0 907 389A, 8D0 907
389D and 8D0 907 389E.
01542
Sender for rotation rate -
G202-
Implausible signal

Continuation:
Fourth:
The zero position of steering angle sensor -G85- is within the specified range, and the zero
position of the combined sensor for rotation rate and transverse acceleration is within the
specified range:

- Check the combined sensor for rotation rate and transverse acceleration by selecting "Read
measuring value block" function 08 page 01
-256
, display group 5


See continuation on next
page
The combined sensor for rotation rate and
transverse acceleration is loose.
Repair Manual, Brake System, Repair
Group 45
- Check bolts for combined sensor for
rotation rate and transverse acceleration.
Pa
ge 92 of 96 Electronic Stabilization Pro
gram
(ESP
) DTC table
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.17