1999 AUDI A4 APB Engine Cooling System Components

19-23

- Replace O-ring on coolant drain screw and
screw drain screw back into engine.

Tightening torque: 20 Nm

- Install bottom coolant hose and secure.

- Close coolant drain tap on radiator.

- Screw adapter VAG 1274/8 onto expansion tank and insert extension
VAG 1274/10 into the adapter.

- Loosen coolant hose on heat exchanger and pull back hose far enough
so that bleeder hole in hose -arrow- is no longer covered by
connection.
- Fill up coolant until it comes out at bleeder hole in coolant hose.
- Push coolant hose onto connection and tighten.
Pa
ge 25 of 34 Coolin
g system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.19.1

19-24


- Loosen bleeder screw on rear coolant line -arrow- below expansion
tank.
- Fill up coolant until it comes out at bleeder screw.
- Screw in bleeder screw (20 Nm).

- Loosen bleeder screw on front coolant line -arrow- between power
steering pump and left cylinder head.
- Fill with coolant until it comes out at bleeder screw.
- Screw in bleeder screw (20 Nm).
- Fill coolant up to max. mark.
- Close filler cap on expansion tank.
- Set heater controls to maximum heat setting.
Pa
ge 26 of 34 Coolin
g system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.19.1

19-25

- Start engine and let it idle for about 10
minutes.

- Maintain an engine speed of about 2000 RPM
for about 5 minutes.

- Allow engine to run at idling speed until bottom
hose on radiator becomes hot.

- Check coolant level and top up if necessary.
When engine is at normal operating temperature
coolant level must be on max. mark, and
between min. and max. marks when engine is
cold.

Note:
When the engine is hot the cooling system is
under pressure. Carefully open filler cap on
expansion tank to release pressure before
starting repair work.

WARNING!

Hot steam can escape from the expansion
tank when the filler cap is opened. Cover the
filler cap with a cloth and remove it carefully.
Pa
ge 27 of 34 Coolin
g system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.19.1

19-26

Radiator, removing and installing


Removing

- Remove front bumper.

Repair Manual, Body Exterior, Repair Group
63


- Drain coolant Page 19
-19
.

- Disengage retaining clips on connecting flanges -arrow- and pull
coolant hoses off radiator.
- Unplug connector from thermoswitch on radiator (bottom left).
Pa
ge 28 of 34 Coolin
g system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.19.1

19-27


Vehicles with air conditioner
WARNING!
Do not open the air conditioner refrigerant circuit.
Note:
To prevent damage to the condenser and refrigerant lines and hoses,
ensure that the lines and hoses are not stretched, kinked or bent. - Unbolt pressurizing fan and detach cooling lines for power steering
hydraulic fluid -arrows-.

- Detach air cowls from radiator -4- (left and right).
- Remove securing bolts -1- and -2- for condenser.
- Unplug connector -3- from air conditioner pressure switch -F129.
- Lift condenser up out of its bracket, turn it towards side and secure to
right-hand front wheel with wire.
Pa
ge 29 of 34 Coolin
g system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.19.1

19-28


Installing
Install in the opposite order to removing. When installing, note the
following points:
Tightening torques - Release two retaining pins for radiator and pull out upward -arrows-.
- Pivot radiator toward front and lift out.
- Fill with coolant Page 19
-19
.
Component
Nm
Condenser to radiator 10
Cooling lines to radiator 10
Pressurizing fan to radiator 10
Pa
ge 30 of 34 Coolin
g system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.19.1

19-29

Coolant pump, removing and installing


Notes:

Always replace seals and gaskets.
Cover toothed belt with a cloth to protect it from
coolant before removing coolant pump.

Removing

- Remove front bumper.

Repair Manual, Body Exterior, Repair Group
63


- Move lock carrier to service position.

Repair Manual, Body Exterior, Repair Group
50


- Remove ribbed belt Page 13
-1 .

- Remove toothed belt Page 13
-4 .
Pa
ge 31 of 34 Coolin
g system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.19.1

- Drain coolant Page 19
-19
.
Pa
ge 32 of 34 Coolin
g system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.19.1