Page 56 of 339
Downloaded from www.Manualslib.com manuals search engine 01-53
V.A.G 1551 print-out
Possible cause
Repair
01314
Engine control module
No communication
- Read measured value block
Page 01
-61 display group number
125
Open circuit, short to
positive or Ground in data
bus wiring - Check wiring and connections of
data bus wiring using wiring
diagram
- Perform electrical checks
Page 01
-102
01315
Transmission Control
Module (TCM)
1)
No communication
- Read measured value block
Page 01-61 display group number
125
Open circuit, short to
positive or Ground in data
bus wiring - Check wiring and connections of
data bus wiring using wiring
diagram
- Perform electrical checks
Page 01
-102
1) Vehicles with automatic transmission only.
Стр. 33из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program
Page 59 of 339
Downloaded from www.Manualslib.com manuals search engine 01-56
Diagnostic Trouble Code (DTC)
memory, erasing and ending output
Note:
All functions which could previously be
performed with V.A.G 1551 can also be
performed with the tester VAS 5051.
Test requirements:
DTC memory checked Page 01-28 .
1. Erasing DTC memory
-
Press key.
Rapid data transfer HELP
Select function XX Indicated on display
- Press keys -0- and -5-; 05 enters "Erase
DTC memory" function.
Rapid data transfer Q
05 - Erase DTC memor
y
Indicated on display
- Confirm entry with Q key
Rapid data transfer
DTC memory is erased!
Indicated on display
-
Press key.
Rapid data transfer HELP
Select function XX Indicated on display
Стр. 36из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program
Page 60 of 339
Downloaded from www.Manualslib.com manuals search engine 01-57
Warning!
DTC memor
y was not interrogated.
Indicated on display
Note:
Adhere exactly to test sequence: First
check DTC memory, then erase
2. Ending output
- Press keys -0- and -6-, to end output.
Rapid data transfer Q
06 - End output Indicated on display
- Confirm input with Q key.
Rapid data transfer HELP
Select function XX Indicated on display
ABS warning light -K47- and warning light
for brake system -K118- must go out after
approx. 2 seconds. - Switch ignition off.
- Disconnect V.A.G 1551 Scan Tool at
Data Link Connector (DLC).
- Switch ignition on.
Стр. 37из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program
Page 61 of 339
Downloaded from www.Manualslib.com manuals search engine 01-58
ABS control module, coding
All functions which could previously be
performed with V.A.G 1551 can also be
performed with the tester VAS 5051.
Warning light for ABS -K47- and warning light
for brake system -K118- flash when control
module is coded with 00000. An entry is not set
in the DTC memory.
The ABS control module (w/EDL) -J104- must
be recoded if the vehicle relevant coding is not
displayed or the control module has been
replaced.
Coding is only possible after the workshop code
(WSC) has been entered into the V.A.G 1551
Scan Tool.
Test sequence
- Connect V.A.G 1551 Scan Tool and select
(address word 03) "Brake electronics" with
ignition switched on; Page 01
-23
- Establish which type of ABS hydraulic control
module is installed Page 01
-4 .
- Establish engine code.
Стр. 38из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program
Page 62 of 339
Downloaded from www.Manualslib.com manuals search engine 01-59
Rapid data transfer HELP
Select function XX Indicated on display
- Input 07 for "Code control module" and
confirm with Q key.
Rapid data transfer Q
07 - Code control module Indicated on display
- Confirm input with Q key.
Coding control module Q
Enter code number XXXXX
(0-32000)
Indicated on display
- Enter relevant code number for this
vehicle and confirm with Q key.
Coding variations Page 01
-60 .
1J0 907 379 D ABS 20 IE CAN 0001
Coding 03604 WSC 00000
On the display the control module
identification and coding are displayed,
e.g.:
Стр. 39из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program
Page 64 of 339
Downloaded from www.Manualslib.com manuals search engine 01-61
Measured value block, reading
Note:
All functions which could previously be
performed with V.A.G 1551 can also be
performed with the tester VAS 5051.
The control module can transfer a considerable
amount of test data. This test data delivers
information on the operational condition of the
system and/or sensors connected to it. In many
cases the transferred test data supports
troubleshooting and repair. The test data has
been summarized into single display groups
because all the information cannot be
evaluated at the same time. The information
can be selected via display group numbers.
Стр. 41из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program
Page 66 of 339
Downloaded from www.Manualslib.com manuals search engine 01-63
- Connect V.A.G 1551 Scan Tool and select
address word 03 for"Brake electronics" with
ignition switched on; Page 01
-23
Rapid data transfer HELP
Select function XX Indicated on display
- Press keys 0 and 8 to select function "Read
measured value block".
Rapid data transfer Q
08 - Read measured value block Indicated on display
- Confirm entry with key Q.
Read measured value block
Enter dis
play group number XXX
Indicated on display
- Enter display group number List of selectable
display group numbers, Page 01
-64 .
Стр. 43из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program
Page 67 of 339
Downloaded from www.Manualslib.com manuals search engine 01-64
List of selectable display group numbers
Display group number
Display zone
Designation
001 1 Wheel speed at left front wheel sensor (km/h)
2 Wheel speed at right front wheel sensor (km/h)
3 Wheel speed at left rear speed sensor (km/h)
4 Wheel speed at right rear speed sensor (km/h)
002 1 Wheel speed at left front speed sensor (km/h)
2 Wheel speed at right front wheel sensor (km/h)
3 Wheel speed at left rear speed sensor (km/h)
4 Wheel speed at right rear speed sensor (km/h)
003 1 Brake light switch
2 Vacant
3 Vacant
4 Vacant
Стр. 44из 81 ABS ITT Mk 20 IE On Board Diagnostic (OBD) program