1998 TOYOTA LAND CRUISER check oil

D11993
(+)
(-)
- DIAGNOSTICSAUTOMATIC TRANSMISSION
DI-471
664 Author
: Date
:
2004 LAND CRUISER (RM1071U)
3 Check shift solenoid valve SR.
PREPARATION:
(a) Jack up the vehicle.
(b) Remove the oil pan.
(c) Remove the shift solenoid valve SR.
CHECK:
Measure the resistance between the solenoid connector termi-
nal and the body ground.
OK:
Resistance: 11 to 15 W at 20°C (68°F)
CHECK:
Connect the battery positive lead to the solenoid connector ter-
minal and the battery negative lead to the solenoid body
ground.
OK:
Solenoid sounds operation noise.

NG Replace the shift solenoid valve SR
(See page AT-8).
OK
Repair or replace the transmission wire
(See page AT-6).

D11987
2
1
DI-478
- DIAGNOSTICSAUTOMATIC TRANSMISSION
671 Author
: Date
:
2004 LAND CRUISER (RM1071U)
INSPECTION PROCEDURE
1 Check shift solenoid valve SLT operation.
PREPARATION:
(a) Jack up the vehicle.
(b) Remove the oil pan.
(c) Remove the shift solenoid valve SLT.
CHECK:
(a) Measure the resistance between terminals 1 and 2 of so-
lenoid connector.
Standard: 5.0 to 5.6 W at 20°C (68°F)
(b) Connect the positive (+) lead with an 21 W bulb to terminal
2 of solenoid connector and negative (-) lead to terminal
1 of the solenoid valve connector, then check the move-
ment of the valve.
Standard: Solenoid sounds operation noise.
OK:
Standard
NG Replace the shift solenoid valve SLT
(See page AT-8).
OK
2 Check valve body (See page DI-396).
NG Replace the valve body (See page AT-8).
OK
Repair or replace transmission (See page
AT-30).

D11987
2 1
DI-482
- DIAGNOSTICSAUTOMATIC TRANSMISSION
675 Author
: Date
:
2004 LAND CRUISER (RM1071U)
3 Check shift solenoid valve SLT.
PREPARATION:
(a) Jack up the vehicle.
(b) Remove the oil pan.
(c) Remove the shift solenoid valve SLT.
CHECK:
(a) Measure the resistance between terminals 1 and 2 of so-
lenoid connector.
Standard: 5.0 to 5.6 W at 20°C (68°F)
(b) Connect the positive (+) lead with an 21 W bulb to terminal
2 of solenoid connector and negative (-) lead to terminal
1 of the solenoid valve connector, then check the move-
ment of the valve.
Standard: Solenoid sounds operation noise.
OK:
Standard

NG Replace the shift solenoid valve SLT
(See page AT-8).
OK
Repair or replace the transmission wire
(See page AT-6).

D12795
12
(-)(+)
12
- DIAGNOSTICSAUTOMATIC TRANSMISSION
DI-489
682 Author
: Date
:
2004 LAND CRUISER (RM1071U)
TYPICAL MALFUNCTION THRESHOLDS
Detection criteriaThreshold
OFF malfunction
Engine speed - Turbine speed70 rpm or more
ON malfunction
It is necessary 2 detections/one driving cycle
1st detection; temporary flag ON
2nd detection; pending fault code ON
Vehicle speed must be under 10 km/h (6 mph) once before 2nd detection
|Engine speed - Turbine speed|Less then 35 rpm
COMPONENT OPERATING RANGE
ParameterStandard value
Speed sensor (NT)Input speed is equal to engine speed when lock-up ON.
INSPECTION PROCEDURE
1 Check shift solenoid valve SLU operation.
PREPARATION:
(a) Jack up the vehicle.
(b) Remove the oil pan.
(c) Remove the shift solenoid valve SLU.
CHECK:
(a) Measure the resistance between terminals 1 and 2 of so-
lenoid connector.
Standard: 5.0 to 5.6 W at 20°C (68°F)
(b) Connect the positive (+) lead with an 21 W bulb to terminal
2 of solenoid connector and negative (-) lead to terminal
1 of the solenoid valve connector, then check the move-
ment of the valve.
Standard: Solenoid sounds operation noise.
OK:
Standard
NG Replace the shift solenoid valve SLU
(See page AT-8).
OK

Current flow to solenoid
Lock-up
Operation
Pressure
BE4056D00160
1 cycle ON
OFFDuty Ratio
=
A + B
A
y 100 (%) (*)
- DIAGNOSTICSAUTOMATIC TRANSMISSION
DI-491
684 Author
: Date
:
2004 LAND CRUISER (RM1071U)
DTC P2759Torque Converter Clutch Pressure Control Solenoid
Control Circuit Electrical(Shift Solenoid Valve SLU)
CIRCUIT DESCRIPTION
The amount of current flow to the solenoid is controlled by the
(*) duty ratio of the ECM output signal. The higher the duty ratio
becomes, the higher the lock-up hydraulic pressure becomes
during the lock-up operation.
(*) Duty Ratio
The duty ratio is the ratio of the period of continuity in one cycle.
For example, if A is the period of continuity in one cycle, and B
is the period of non-continuity, then
DTC No.DTC detection conditionTrouble Area
P2759
The following condition is detected. (1-trip detection logic)
SLU output signal's duty ON of 3.3 msec. or more with duty
ratio of least 95% lasts for 1 second.
Open or short in shift solenoid valve SLU circuit

Shift solenoid valve SLU

ECM
MONITOR DESCRIPTION
The ECM controls the oil pressure to the lock-up clutch based on engine-load information from the throttle
position sensor, crankshaft position sensor, input speed sensor, and the oil pressure sensor for shift-sole-
noid SLU. The ECM commands the shift-solenoid SLU using a duty-cycle control signal. In turn, the shift
solenoid operates the lock-up control valve and cause lock-up or flexible lock-up of the torque converter
clutch. The ECM illuminates the MIL and store the DTC when ECM detects an open or a short circuit malfunc-
tion in the shift solenoid valve SLU.
MONITOR STRATEGY
Related DTCsP2759Shift solenoid valve SLU/Range check
Required sensors/ComponentsShift solenoid valve SLU
Frequency of operationContinuous
Duration1 sec.
MIL operationImmediate
Sequence of operationNone
DIB3M-02

D12795
12
(-)(+)
12
DI-494
- DIAGNOSTICSAUTOMATIC TRANSMISSION
687 Author
: Date
:
2004 LAND CRUISER (RM1071U)
3 Check shift solenoid valve SLU.
PREPARATION:
(a) Jack up the vehicle.
(b) Remove the oil pan.
(c) Remove the shift solenoid valve SLU.
CHECK:
(a) Measure the resistance between terminals 1 and 2 of so-
lenoid connector.
Standard: 5.0 to 5.6 W at 20°C (68°F)
(b) Connect the positive (+) lead with an 21 W bulb to terminal
2 of solenoid connector and negative (-) lead to terminal
1 of the solenoid valve connector, then check the move-
ment of the valve.
Standard: Solenoid sounds operation noise.
OK:
Standard

NG Replace the shift solenoid valve SLU
(See page AT-8).
OK
Repair or replace the transmission wire
(See page AT-6).

- DIAGNOSTICSAUTOMATIC TRANSMISSION
DI-367
560 Author
: Date
:
6. DEFINITION OF TERMS
TermDefinition
Monitor descriptionDescription of what the ECM monitors and how it detects malfunctions (monitoring purpose and its details).
Related DTCsDiagnostic code
Typical enabling condition
Preconditions that allow the ECM to detect malfunctions.
With all preconditions satisfied, the ECM sets the DTC when the monitored value(s) exceeds the malfunction
threshold(s).
Sequence of operation
The priority order that is applied to monitoring, if multiple sensors and components are used to detect the malfunc-
tion.
While another sensor is being monitored, the next sensor or component will not be monitored until the previous
monitoring has concluded.
Required sensor/compo-
nentsThe sensors and components that are used by the ECM to detect malfunctions.
Frequency of operation
The number of times that the ECM checks for malfunctions per driving cycle.
ºOnce per driving cycleº means that the ECM detects malfunction only one time during a single driving cycle.
ºContinuousº means that the ECM detects malfunction every time when enabling condition is met.
DurationThe minimum time that the ECM must sense a continuous deviation in the monitored value(s) before setting a
DTC. This timing begins after the ºtypical enabling conditionsº are met.
Malfunction thresholdsBeyond this value, the ECM will conclude that there is a malfunction and set a DTC.
MIL operation
MIL illumination timing after a defect is detected.
ºImmediatelyº means that the ECM illuminates MIL the instant the ECM determines that there is a malfunction.
º2 driving cycleº means that the ECM illuminates MIL if the same malfunction is detected again in the 2nd driving
cycle.
7. TOYOTA/LEXUS PART AND SYSTEM NAME LIST
This reference list indicates the part names used in this manual along with their definitions.
TOYOTA/LEXUS nameDefinition
Toyota HCAC system, Hydrocarbon adsorptive Catalyst
(HCAC) system, HC adsorptive three-way catalystHC adsorptive three-way catalytic converter
Variable Valve Timing sensor, VVT sensorCamshaft position sensor
Variable valve timing system, VVT systemCamshaft timing control system
Camshaft timing oil control valve, Oil control valve OCV,
VVT, VSVCamshaft timing oil control valve
Variable timing and lift, VVTLCamshaft timing and lift control
Crankshaft position sensor ºAºCrankshaft position sensor
Engine speed sensorCrankshaft position sensor
THAIntake air temperature
Knock control moduleEngine knock control module
Knock sensorEngine knock sensor
Mass or volume air flow circuitMass air flow sensor circuit
Vacuum sensorManifold air pressure sensor
Internal control module, Control module, Engine control
ECU, PCMPower train control module
FC idleDeceleration fuel cut
Idle air control valveIdle speed control
VSV for CCV, Canister close valve VSV for canister controlEvaporative emissions canister vent valve
VSV for EVAP, Vacuum switching valve assembly No. 1,
EVAP VAV, Purge VSVEvaporative emissions canister purge valve
VSV for pressure switching valve, Bypass VSVEvaporative emission pressure switching valve
Vapor pressure sensor, EVAP pressure sensor, Evaporative
emission control system pressure sensorFuel tank pressure sensor
Charcoal canisterEvaporative emissions canister
ORVR systemOn-boad refueling vapor recovery system
Intake manifold runner controlIntake manifold tuning system
Intake manifold runner valve, IMRV, IACV (runner valve)Intake manifold tuning valve
Intake control VSVIntake manifold tuning solenoid valve

D12745
SST
SST
DI-378
- DIAGNOSTICSAUTOMATIC TRANSMISSION
571 Author
: Date
:
15. HYDRAULIC TEST
Measure the line pressure.
NOTICE:

Do the test at normal operation fluid temperature 70
to 80°C (158 to 176°F).

The line pressure test should always be carried out in
pairs. One technician should observe the conditions
of wheels or wheel stoppers outside the vehicle while
the other is doing the test.

Be careful to prevent SST's hose from interfering with
the exhaust pipe.

This check must be conducted after checking and ad-
justing engine.

Perform under condition that A/C is OFF.

When conducting stall test, do not continue more
than 10 seconds.
(1) Warm up the ATF.
(2) Remove the test plug on the transmission case cen-
ter right side and connect SST.
SST 09992-00095 (09992-00231, 09992-00271)
(3) Fully apply the parking brake and chock the 4
wheels.
(4) Start the engine and check idling speed.
(5) Keep your left foot pressing firmly on the brake ped-
al and shift into D position.
(6) Measure the line pressure when the engine is idling.
(7) Depress the accelerator pedal all the way down.
Quickly read the highest line pressure when engine
speed reaches stall speed.
(8) In the same manner, do the test in R position.
Specified line pressure:
ConditionD position kPa (kgf/cm2
, psi)R position kPa (kgf/cm2, psi)
Idling362 to 420 (3.7 to 4.2, 53 to 59)500 to 580 (5.1 to 5.9, 73 to 84)
Stall1,360 to 1,460 (13.8 to 14.9, 196 to 212)1,295 to 1,415 (13.2 to 14.4, 188 to 205)
Evaluation
ProblemPossible cause
If the measured value at all positions are higher
Shift solenoid valve SLT defective

Regulator valve defective
If the measured value at all positions are lower

Shift solenoid valve SLT defective

Regulator valve defective

Oil pump defective
If pressure is low in the D position only
D position circuit fluid leakage

Clutch No. 1 (C
1) defective
If pressure is low in the R position only

R position circuit fluid leakage

Clutch No. 3 (C
3) defective

Brake No. 4 (B
4) defective