1998 TOYOTA 4RUNNER brake light

4RUNNER (1998)
If your vehicle remains stuck af-
ter rocking the vehicle severaltimes, consider other ways such as towing.
(h) Driving in ºPWRº (Power) mode
In the ºPWRº mode, the transmission
is shifted up and down at a higher
vehicle speed than in the ºNORMº
(Normal) mode and a more powerful
acceleration is achieved. To set the
ºPWRº mode, push in the driving pat-
tern selector button. The ºPWRº mode
indicator light comes on.
For ordinary driving, Toyota recom-
mends using the ºNORMº mode to im-
prove fuel economy.
(i) If you cannot shift the selector lever out of ºPº position
If you cannot shift the selector lever
from the ºPº position even though the
brake pedal is depressed, use the
shift lock override button. For instruc-
tions, see ºIf you cannot shift auto-
matic transmission selector leverº in
Part 4.

4RUNNER (1998)
Lock release button
To prevent misshifting
Parking, engine starting and key removal position Reverse position Neutral position Normal driving position Position for engine braking Position for stronger engine braking than that in º2º posi- tion
With the brake pedal depressed, shift while holding the lock release button in. (The ignition switch must be in ºONºposition.) Shift while holding the lock release button in. Shifting normally Overdrive switch
For selecting either a three-speed or four-speed transmission
ºONº position(Shifting into overdrive pos-sible) ºOFFº position (Shifting into overdrive notpossible)ºO/D OFFº indicator light shows the over- drive switch is inOFF position
Driving pattern selector button For selecting a driving pattern suited to existing driving conditions
ºNORMº (Normal)mode for general driving conditioning ºPWRº (Power) mode for power- ful accelerationºPWRº mode indicator light on the instrument panel shows the driving pattern selector button isin the ºPWRº mode
Vehicles with cruise control ' When the cruise control is being used, even if you downshift the trans mission by turning
off the overdrive switch, engine braking will not be applied because the cruise control is not cancelled. For ways to
decrease the vehicle speed, see ºCruise controlº in this chapter. Automatic transmission
Four- wheel drive control

4RUNNER (1998)
Your automatic transmission has a
shift lock system to minimize the pos-
sibility of incorrect operation. This
means you can only shift out of ºPº
position when the brake pedal is de-
pressed (with the ignition switch in
ºONº position and the lock release
button depressed).
(a) Normal driving
1. Start the engine as instructed in
ºHow to start the engineº in Part 3.
The transmission must be in ºPº or
ºNº.
When the front drive control lever is
in ºL4º (low- speed position, four-
wheel drive), the driving pattern selec-
tor setting has no effect on gear shift
timing. (See ºFour- wheel drive sys-
temº in this Chapter for information of
the front drive control lever.)
2. With your foot holding down the
brake pedal, shift the selector lever to
ºDº.
In ºDº position, the automatic trans-
mission system will select the most
suitable gear for running conditions
such as normal cruising, hill climbing,
hard towing, etc. Always turn the overdrive switch on
for better fuel economy and quieter
driving. If the engine coolant tempera-
ture is low or when the front drive
control lever is in ºL4º (low- speed
position, four- wheel drive), the trans-
mission will not shift into
the overdrive gear even with the over-
drive switch on. (See ºFour- wheel
drive systemº in this Chapter for in-
formation of the front drive control le-
ver.)
CAUTION
Never put your foot on the accel-
erator pedal while shifting.
3. Release the parking brake and
brake pedal. Depress the accelerator
pedal slowly for smooth starting.
(b) Using engine braking
To use engine braking, you can down-
shift the transmission as follows:
Turn off the overdrive switch. The
ºO/D OFFº indicator light will come
on and the transmission will down-
shift to the third gear.
Shift into the º2º position. The
transmission will downshift to the
second gear when the vehicle
speed drops down to or lower than
the following speed, and more pow-
erful engine braking will be ob-
tained.
Front drive control lever in ºH2º or
ºH4º
3RZ- FE engine.....105 km/h (65
mph)
5VZ- FE engine.....114 km/h (70
mph)
Front drive control lever in ºL4º
3RZ- FE engine.....38 km/h (23
mph)
5VZ- FE engine.....41 km/h (25
mph)
Shift into the ºLº position. The
transmission will downshift to the
first gear when the vehicle speed
drops down to or lower than the
following speed, and maximum en-
gine braking will be applied.
Front drive control lever in ºH2º or
ºH4º
3RZ- FE engine.....51 km/h (31
mph)
5VZ- FE engine.....55 km/h (34
mph)

4RUNNER (1998)
CAUTION
While the vehicle is moving, nev-
er attempt to move the selector
lever into ºPº position under any
circumstances. Serious mechani-
cal damage and loss of vehicle
control may result.
(f) Good driving practice
If the transmission is repeatedly
upshifted and downshifted between
third gear and overdrive when
climbing a gentle slope, the over-
drive switch should be turned off.
Be sure to turn the switch on im-
mediately afterward.
When towing a trailer, in order to
maintain engine braking efficiency,
do not use overdrive.
CAUTION
Always keep your foot on the
brake pedal while stopped with
the engine running. This prevents
the vehicle from creeping.
NOTICE
Do not hold the vehicle on an
upgrade with the accelerator pe-dal. It can cause the transmissionto overheat. Always use the brake
pedal or parking brake.
(g) Rocking your vehicle if stuck
CAUTION
To rock your vehicle if it becomes
stuck in snow, mud, sand, etc.,
first check that there are no ob-
jects or people around the ve-
hicle. During the rocking opera-
tion the vehicle may suddenly
move forward or backward as it
becomes unstuck, causing injury
or damage to nearby people or
objects.
NOTICE
If you rock your vehicle, observe
the following precautions to pre-vent damage to the transmissionand other parts.
Do not depress the accelerator
pedal while shifting the selectorlever or before the transmissionis completely shifted to forward
or reverse gear.
Do not race the engine andavoid spinning the wheels.
If your vehicle remains stuck af-ter rocking the vehicle several
times, consider other ways suchas towing.
(h) Driving in ºPWRº(Power) mode
In the ºPWRº mode, the transmission
is shifted up and down at a higher
vehicle speed than in the
ºNORMº(Normal) mode and a more
powerful acceleration is achieved. To
set the ºPWRº mode, push in the driv-
ing pattern selector button. The ºPWRº
mode indicator light comes on.
For ordinary driving, Toyota recom-
mends using the ºNORMº mode to im-
prove fuel economy.

4RUNNER (1998)
SHIFTING BETWEEN ºH2º AND ºH4º
To shift from ºH2º to ºH4º, move
the front drive control lever.
This can be done when the vehicle is
stopped, or moving straight ahead at
speeds of 40 km/h (25 mph) or less.
If you have trouble shifting, depress
or release the accelerator pedal mo-
mentarily while pushing the front drive
control lever.
CAUTION
Never move the front drive con-
trol lever if wheels are slipping.
Stop the slipping or spinning be-
fore shifting.
To shift from ºH4º to ºH2º, simply
move the front drive control lever.
This can be done at any vehicle
speed.
If the indicator light does not go off
when you shift the transfer into ºH2º,
drive straight ahead while accelerating
or decelerating, or drive in reverse. With A.D.D.
To shift from ºH2º to ºH4º,
reduce
your speed to less than 80 km/h (50
mph) and move the front drive control
lever.
If you have trouble shifting in cold
weather, reduce your speed or stop
the vehicle and reshift.
CAUTION
Never move the front drive con-
trol lever if wheels are slipping.
Stop the slipping or spinning be-
fore shifting.
To shift from ºH4º to ºH2º, simply
move the front drive control lever.
This can be done at any vehicle
speed.
If the indicator light does not go off
when you shift the transfer into ºH2º,
drive straight ahead while accelerating
or decelerating, or drive in reverse.
SHIFTING BETWEEN ºH4º ANDºL4º
To shift between ºH4º and ºL4º, stop
the vehicle and put the transmission
in ºNº. With your foot holding down
the brake pedal, move the front drive
control lever. SHIFTING BETWEEN ºH2º AND ºH4º
To shift from ºH2º to ºH4º,
reduce
your speed to less than 100 km/h (62
mph) and push in the º4WDº button.
If the indicator light does not come on
when you push in the º4WDº button,
drive straight ahead while accelerating
or decelerating.
If the indicator light flashes and the
buzzer sounds when you push in the
º4WDº button, reduce your speed or
stop the vehicle and reset.
CAUTION
Never push the º4WDº button if
wheels are slipping. Stop the slip-
ping or spinning before shifting.
(c) Shifting procedure (lev
type with automa
t
transmission) (c) Shifting procedure
(lever/button type)

4RUNNER (1998)
To shift from ºH4º to ºH2º, push the
º4WDº button again to turn it off.
This can be done at any vehicle
speed.
If the indicator light does not go off
when you shift the transfer into ºH2º,
drive straight ahead while accelerating
or decelerating, or drive in reverse.
SHIFTING BETWEEN ºH2º OR ºH4º
AND ºL4º
To shift from ºH2º or ºH4º to ºL4º,
stop the vehicle and put the trans-
mission in ºNº. With your foot holding
down the brake pedal, move the front
drive control lever.
To shift from ºL4º to ºH2º or ºH4º,
stop the vehicle and put the trans-
mission in ºNº. With your foot holding
down the brake pedal, move the front
drive control lever. When the º4WDº
button is pushed in, the transfer shifts
into ºH4º; when the button is left out,
the transfer shifts into ºH2º.
If the indicator light does not go off
when you shift the transfer into ºH2º,
drive straight ahead while accelerating
or decelerating, or drive in reverse. Rear differential lock system

4RUNNER (1998)
To lock the rear differential, push
the switch.
Be sure to stop the wheels before
locking the differential.
Vehicles with manual transmis-
sion'For easy locking, depress the
clutch pedal, push the lock switch and
slowly release the clutch pedal.
The indicator light will blink when the
switch is turned on. Wait a few se-
conds for the system to complete op-
eration. After the differential is locked,
the light will stop blinking and remain on. The anti- lock brake system does not
operate when the rear differential is
locked. It is normal operation for the
ºABSº warning light to be on at this
time.CAUTION

Do not lock the differential until
the wheels have stopped spin-
ning. Otherwise, the vehicle
may move in an unexpected
direction when the differential
lock is engaged, resulting in an
accident. This may also lead to
possible damage to differential
lock component parts.
Do not drive over 8 km/h (5
mph) when the differential is
locked.
To unlock the differential, push the
switch once again.
Unlock the differential as soon as the
vehicle moves out.

4RUNNER (1998)
For easy unlocking, slightly turn the
steering wheel in either direction while
the vehicle is in motion.
When the differential lock is disen-
gaged, the indicator light will go out. The differential will also unlock if you
shift the front drive control lever out
of ºL4º. Never forget to turn off the
switch after using this feature.
To check the indicator bulb, turn the
ignition key to the ºONº position, but
do not start the engine.
CAUTION
Do not keep driving with the dif-
ferential lock switch on.
Parking brake
When parking, firmly apply the
parking brake to avoid inadvertent
creeping.
To set: Pull up the lever. For better
holding power, first depress the brake
pedal and hold it while setting the
brake.
To release: Pull up the lever slightly,
press the thumb button, and lower.To remind you that the parking brake
is set, the parking brake reminder
light in the instrument panel remains
on until you release the parking brake.