1998 SUZUKI GRAND VITARA sensor

YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-35
FORWARD
1. Front wheel speed
sensor connector
2. Headlight assembly
1. Front wheel speed sensor
2. Bolt
REMOVAL
1) Disconnect negative cable at battery.
2) Hoist vehicle and remove wheel.
3) Disconnect front wheel speed sensor connector.
4) Remove harness clamp bolts and remove front wheel speed
sensor from knuckle.
CAUTION:

Do not pull wire harness when removing front wheel
speed sensor.

Do not cause damage to surface of front wheel speed
sensor and do not allow dust, etc. to enter its installa-
tion hole.
SENSOR INSPECTION

Check sensor for damage.

Check sensor for resistance.
Resistance between terminals: 1.2 ± 1.6 k
at 20C (68F)
Resistance between terminal and sensor body: 1 M
or more
If any faulty is found, replace.
SENSOR ROTOR INSPECTION

Check rotor for being missing, damaged or deformed.

Turn drive shaft and check if rotor rotation is free from eccentricity
and looseness.

Check that no foreign material is attached.
If any faulty is found, repair or replace. Refer to WHEEL HUB RE-
MOVAL and INSTALLATION in Section 3D.

YH4
GRAND
VITARA
5E1-36 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
1. Front wheel speed sensor
2. Bolt
INSTALLATION
1) Check that no foreign material is attached to sensor and rotor.
2) Install it by reversing removal procedure.
CAUTION:

Do not pull wire harness or twist more than necessary
when installing front wheel speed sensor.

Fit harness grommet to inner fender securely.
Tightening Torque
(a): 10 N
.m (1.0 kg-m, 7.5 lb-ft)
(b): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
3) Check that there is no clearance between sensor and knuckle.
FRONT SENSOR ROTOR
REMOVAL
Remove front sensor rotor referring to WHEEL HUB REMOVAL in
Section 3D.
INSTALLATION
CAUTION:
Don't reuse front sensor rotor removed from front wheel
hub because of it for being deformed.
Install new front sensor rotor referring to WHEEL HUB INSTALLA-
TION in Section 3D.

YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-37
1. Rear wheel speed sensor
2. Sensor rotor
3. Rear axle housing
1. Rear wheel speed
sensor harness
2. Connector
1. Sensor bolt
2. Clamps
REAR WHEEL SPEED SENSOR
OUTPUT VOLTAGE INSPECTION
Check in the same procedure as that used of front wheel speed
sensor check.
Output AC voltage at 2 / 3 to
one rotation per second (25 ± 38 Hz): 106 mV or more
Reference
When using oscilloscope,
peak-to-peak voltage at 2 / 3 to
one rotation per second (25 ± 38 Hz): 150 mV or more
REMOVAL
1) Disconnect negative cable at battery.
2) Hoist vehicle.
3) Disconnect rear wheel speed sensor connector and detach wire
harness from vehicle body and rear axle.
4) Remove harness clamps and remove rear wheel speed sensor
from rear axle.
CAUTION:

Do not pull wire harness when removing rear wheel
speed sensor.

Do not cause damage to surface of rear wheel speed
sensor and do not allow dust, etc. to enter its installa-
tion hole.

YH4
GRAND
VITARA
5E1-38 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
1. Clamps
2. Sensor bolt
SENSOR INSPECTION

Check sensor (pole piece) for damage or bent.

Check sensor for resistance.
Resistance between
terminals : 1.2 ± 1.6 k
at 20C, 68F
Resistance between
terminal and sensor body: 1 M
or more
If any faulty is found, replace.
SENSOR ROTOR INSPECTION

Check rotor serration (teeth) for being missing, damaged or de-
formed.

Turn wheel and check if rotor rotation is free from eccentricity and
looseness.

Check that no foreign material is attached.
If any faulty is found, repair or replace.
INSTALLATION
1) Check that no foreign material is attached to sensor and rotor.
2) Install it by reversing removal procedure.
Tightening Torque
(a): 21 N
.m (2.1 kg-m, 15.0 lb-ft)
CAUTION:
Do not pull wire harness or twist more than necessary
when installing rear wheel speed sensor.
3) Check that there is no clearance between sensor and knuckle.

YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-39
1. Rear axle
2. Retainer ring
3. Sensor rotor
4. Vinyl envelope
ªAº Grind with grinderªAº
1. Sensor rotor 4
31
2
2 1
3
REAR SENSOR ROTOR
REMOVAL
1) Remove rear axle shaft. Refer to REAR AXLE SHAFT RE-
MOVAL in Section 3E.
2) In order to remove sensor rotor from retainer ring, grind with a
grinder one part of the sensor rotor as illustrated till it becomes
thin.
CAUTION:

Cover vinyl sheet or the like over wheel bearing so that
fine grains from grinding will not enter there.

Be careful not to go so far as to grind the retainer ring.
3) Break with a chisel the thin ground sensor rotor, and it can be re-
moved.
INSTALLATION
1) Press-fit sensor rotor as shown.
NOTE:
Use care not to cause any damage to outside of retainer
ring.
2) Install rear axle shaft. Refer to REAR AXLE SHAFT INSTALLA-
TION in Section 3E.

YH4
GRAND
VITARA
5E1-40 ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL)
1. Parking brake
lever ass'y
2. G sensor
3. Bolt ª1º
4. Bolt ª2º
[A] Horizontal
[B] Upright with
arrow upward
[C] Upright with
arrow downward
A: Forward
G SENSOR (FOR 4WD MODEL ONLY)
REMOVAL
1) Turn ignition switch OFF and disconnect battery negative cable.
2) Remove rear center console box.
3) Remove parking brake lever bolts ª1º and G sensor with bracket
from floor.
NOTE:
Loosen only bolt ª2º.
4) Remove sensor with bracket from floor.
5) Disconnect connector from sensor.
CAUTION:

Do not separate sensor and bracket. It will lead to erro-
neous assembly.

Sensor must not be dropped or shocked. It will affect its
original performance.
INSPECTION
1) Check sensor bracket for bend.
2) Connect positive cable of 12 volt battery to ªAº terminal of sensor
and ground cable to ªCº terminal. Then using voltmeter, check
voltage between ªBº terminal and ªCº terminal.
When placed horizontally: 2 ± 3 V
When placed upright with arrow upward: 3 ± 4 V
When placed upright with arrow downward: 1 ± 2 V
If measured voltage is not as specified, replace sensor with
bracket.
INSTALLATION
1) Connect connector to sensor securely.
2) Install sensor with bracket and parking lever assy onto floor so
that arrow mark directs vehicle forward.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
3) Install rear console box.

YH4
GRAND
VITARA
ANTILOCK BRAKE SYSTEM (ABS) (OPTIONAL) 5E1-41
(d)
TRANSFER 4WD SWITCH
For removal, inspection and installation of this switch, refer to
SWITCHES in Section 7A.
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Brake pipe flare nut: (a)161.611.5
ABS hydraulic unit nut: (b)212.115.5
ABS hydraulic unit bracket bolt: (c)101.07.5
Wheel speed sensor bolt(Front): (d)232.317.0Wheel s eed sensor bolt(Rear): (e)212.115.5
Parking lever assy mounting bolt: (f)232.317.0

YH4
GRAND
VITARA
1. Match mark
1. Flange bolt
2. Front propeller shaft
1. Transmission jack
2. Engine rear mounting member
7A-10 MANUAL TRANSMISSION (TYPE 1)
ON LIFT
1) Drain oil from transmission and transfer.
2) Give match marks on joint flange and propeller shaft as shown
in figure. (front and rear)
3) Remove flange bolts of rear propeller shaft universal joint and
pull out propeller shaft.
4) Remove flange bolts of front propeller shaft universal joint and
pull out propeller shaft.
5) Remove clutch operating cylinder from transmission. It is not
necessary to disconnect clutch hose from operating cylinder.
NOTE:

It is not necessary to drain transmission oil when dis-
mounting transmission and transfer for clutch mainte-
nance only.

Work without draining transfer oil is possible if front pro-
peller shaft is dismounted together with transmission and
transfer.
6) Remove clutch housing lower plate.
7) Disconnect couplers from 4WD switch, back up light switch and
speed sensor assembly and release their harness from clamps.
Remove nuts from joint with engine.
8) Apply transmission jack and remove engine rear mounting
member taking off its bolts.
9) After removing mounting member, move rearward transmission
and transfer assemblies placed on jack and then lower them.