1998 SUZUKI GRAND VITARA Over drive

YH4
GRAND
VITARA
1. Dipstick (G16 / J20)
2. Dipstick (H25)
AUTOMATIC TRANSMISSION (4 A / T) 7B1-59
ON-VEHICLE SERVICE
MAINTENANCE SERVICE
FLUID LEVEL
LEVEL CHECK AT NORMAL OPERATING TEMPERATURE
1) Stop vehicle and place it level.
2) Apply parking brake and place chocks against wheels.
3) With selector at P position, start engine.
4) Warm up engine till fluid temperature reaches normal operating
temperature (70 ± 80C / 158 ± 176F). As a guide to check fluid
temperature, warm up engine till engine coolant temperature
meter indicated around 1 unit above ªCº point.
5) Keep engine idling and shift selector slowly to L and back to P
position.
6) With engine idling, pull out dipstick, wipe it off with a clean cloth
and put it back into place.
7) Pull out dipstick again and check fluid level indicated on it. Fluid
level should be between FULL HOT and LOW HOT. If it is below
LOW HOT, add an equivalent of DEXRON-III up to FULL HOT.
Fluid specification
An equivalent of DEXRON-III
NOTE:

DO NOT RACE ENGINE while checking fluid level, even af-
ter the engine start.

DO NOT OVERFILL. Overfilling can causes foaming and
loss of fluid through breather. Then slippage and trans-
mission failure can result.

Bringing the level from LOW HOT to FULL HOT requires
0.3 liters (0.64/0.53 US/lmp.pt).

If vehicle was driven under high load such as pulling a
trailer, fluid level should be checked about half an hour af-
ter it is stopped.

YH4
GRAND
VITARA
1. Dipstick (G16 / J20)
2. Dipstick (H25)
1. Drain plug
2. Propeller shaft
1. Dipstick (G16 / J20)
2. Dipstick (H25)
7B1-60 AUTOMATIC TRANSMISSION (4 A / T)
LEVEL CHECK AT ROOM TEMPERATURE
The fluid level check at room temperature performed after repair or
fluid change before test driving is just preparation for level check of
normal operating temperature. The checking procedure itself is the
same as that described previously. If the fluid level is between FULL
COLD and LOW COLD, proceed to test drive. And when the fluid
temperature has reached the normal operating temperature, check
fluid level again and adjust it as necessary.
FLUID CHANGE
1) Lift up vehicle.
2) With engine is cool, remove drain plug from oil pan and drain A / T
fluid.
3) Install drain plug.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
4) Lower vehicle and fill proper amount of an equivalent of DEX-
RON
-III.
5) Check fluid level according to procedure described under LEV-
EL CHECK NORMAL OPERATING TEMPERATURE.
Fluid specification
An equivalent of DEXRON
-III
Fluid capacity
When draining
from drain plug
hole
2.5 liters (5.28/4.40 US/lmp.pt.)
When
overhauling
6.9 liters (14.58/12.14 US/lmp.pt.)
for G16
7.1 liters (15.00/12.50 US/lmp.pt.)
for J20 / H25

YH4
GRAND
VITARA
1. Manual selector assembly
(Select lever assembly)
2. Manual lever assembly
3. Select cable bracket
4. Select indicator
5. Slide cover
6. Select lever knob7. Spring
8. Knob button
9. Shift lock solenoid rod
10. Shift lock solenoid
11. Cover
12. Illumination lamp
13. Interlock cam
1. Interlock cam pin
(only for new selector assembly) Tightening Torque
(a): 18 N
.m (1.8 kg-m, 13.5 lb-ft)1. Manual lever
assembly
2. Select indicator
assembly
3. Illumination lamp
assembly
4. Bulb filter
5. Bulb
6. Knob assembly
7. Shift lock solenoid
Type-1 Type-2
Type-1
7B1-62 AUTOMATIC TRANSMISSION (4 A / T)
MANUAL SELECTOR ASSEMBLY
REMOVAL
1) Disconnect negative cable at battery.
2) Remove console box.
3) Disconnect connector for illumination lamp, shift lock solenoid
and overdrive OFF switch.
4) Disconnect interlock cable from interlock cam of selector as-
sembly.
5) Remove selector assembly mounting bolts.
6) Disconnect select cable from lever of selector assembly.
INSTALLATION
NOTE:
New selector assembly of Type-1 is supplied with held inter-
lock cam at interlock cable connecting position with pin. Re-
move this pin after connecting interlock cable to interlock cam
and tightening cable nut.
Reverse removal procedure to install noting the followings.

Connect interlock cable end to cam referring to steps 2) to 8) of
ªInterlock Cable Installationº section.

Upon completion of installation, confirm that brake (key) interlock
system operates properly.

YH4
GRAND
VITARA
Type-2
1. Select lever
2. Detent pin
3. Detent plate4. Lock plate
5. Shift lock solenoid
1. Cover
2. Screw3. Select lever
4. Button
AUTOMATIC TRANSMISSION (4 A / T) 7B1-69
SHIFT LOCK (SOLENOID) MANUAL RELEASE
Shift lock can be manually released by following procedure.
1) Remove access hole cover by unfastening screw.
2) Turn ignition key to ªACCº position and move shift lock solenoid
rod (or manual release plate) toward rear side of vehicle by using
screw driver or the like.
3) In this state, select lever can be moved to any range or position.
SYSTEM INSPECTION
1) Check to make sure that select lever cannot be moved to any
other range from ªPº range position when ignition switch key is
at ªACCº position, at ªLOCKº position (or it is removed from key-
hole of ignition switch) or brake pedal is not depressed.
2) Shift select lever to ªPº range position, release knob button and
check for the following.

Ignition key can be turned between ªLOCKº and ªACCº posi-
tions back and forth and also it can be removed from ignition
switch.

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-75
1. Drain plug
2. Filler and level plug
1. Drain plug
2. Front propeller shaft
1. Match marks
1. Right side transmission stiffener (if equipped)
G16 / J20
ON LIFT
1) Drain transfer oil for 4WD vehicle or A / T fluid for 2WD vehicle.
NOTE:
If 4WD automatic transmission is overhauled later on,
draining A / T fluid at this point will facilitate work.
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
2) Before removing propeller shaft, give match marks on joint
flange and propeller shaft as shown in left figure.
3) Remove universal joint flange bolts and take out rear propeller
shaft.
4) Likewise, take out front propeller shaft. (if equipped)
5) Remove nut from the end of select cable and bracket to set
cable free.
6) Remove select cable bracket by removing its 2 bolts.
7) Remove exhaust No.1 and No.2 pipe.
8) Remove transmission stiffener (right side) if equipped.
9) Unclamp and disconnect oil cooler hoses from pipes.
NOTE:
To avoid leakage of transmission fluid, plug open ends of
oil cooler pipes and hoses right after they are discon-
nected.
10) Remove torque converter housing lower plate.
11) Holding drive plate stationary with special tool or the like, re-
move torque converter mounting bolts with wrench.
Special Tool (only for G16 / J20)
(A): 09927-56010

YH4
GRAND
VITARA
1. Crankshaft
2. Flywheel
3. Clutch disc
4. Pressure plate
5. Clutch cover
6. Diaphragm spring
7. Release bearing
8. Input shaft bearing
9. Input shaft
10. Operating cylinder
11. Clutch housing
12. Release fork
7C1-2 CLUTCH
The clutch is a diaphragm-spring clutch of a dry single
disc type. The diaphragm spring is of a tapering-finger
type, which is a solid ring in the outer diameter part,
with a series of tapered fingers pointing inward.
The disc, carrying torsional coil springs, is positioned
on the transmission input shaft with an involute spline
fit.
The clutch cover is secured to the flywheel, and car-
ries the diaphragm spring in such a way that the pe-
ripheral edge part of the spring pushes on the pres-
sure plate against the flywheel (with the disc in be-
tween), when the clutch release bearing is held back.
This is the engaged condition of the clutch.Depressing the clutch pedal causes the release bear-
ing to advance and pushes on the tips of the tapered
fingers of the diaphragm spring. When this happens,
the diaphragm spring pulls the pressure plate away
from the flywheel, thereby interrupting the flow of
drive from flywheel through clutch disc to transmis-
sion input shaft.
GENERAL DESCRIPTION

YH4
GRAND
VITARA
DIFFERENTIAL (FRONT) 7E-17
09951-16080
Bearing installer09951-26010
Bush remover plate09918-18110
Air pressure regulator
09367-04002
3-way joint
UNIT REPAIR
Refer to the same section of UNIT REPAIR MANUAL mentioned in FOREWORD of this manual.
TIGHTENING TORQUE SPECIFICATIONS
FasteningportionTightening torqueFastening ortionN.mKg-mlb-ft
Differential oil filler / level plug232.317.0
Differential oil drain plug232.317.0
Differential mounting front bolts858.561.5
Differential mounting bracket bolts505.036.5
Front drive shaft flange bolts505.036.5
Propeller shaft flange bolts505.036.5
Pump assembly bolts131.39.5
REQUIRED SERVICE MATERIAL
MATERIALRECOMMENDED
SUZUKI PRODUCTUSE
SealantSUZUKI BOND NO. 1215
(99000-31110)Front differential drain plug
SPECIAL TOOLS

YH4
GRAND
VITARA
LH steering vehicle shown
X-X:Horizontal center line of headlight bulbs
A-A:Vertical center line of left headlight bulb
B-B:Vertical center line of right headlight bulb1. Screen
2. For right / left adjustment
3. For up / down adjustment
(for vehicle without leveling system)
4. For up / down adjustment
(for vehicle with leveling system)
5. Headlight leveling actuatorHOT
SPOT LH. HEADLIGHT RH. HEADLIGHT
LIGHTING SYSTEM 8B-7
BULB REPLACEMENT
WARNING:
Don't touch when the bulb is hot.
1) Disconnect negative cable at battery.
2) Disconnect harness from bulb.
3) Remove socket cover and bulb.
4) Replace bulb and install in reverse removal procedure.
HEADLIGHT AIMING WITH SCREEN
NOTE:

Unless otherwise obligated by local regulations, adjust
headlight aiming according to following procedure.

After replacing headlight, be sure to perform its aiming.

When inspecting and adjusting headlight with leveling sys-
tem, make sure to set the leveling switch to ª0º position with
IG switch ON.
Before adjustment, make sure the following.
a) Place vehicle on a flat surface in front of blank wall as below
ahead of headlight surface.
Clearance ªaº: 10 m (32.8 ft)
b) Adjust air pressure of all tires to a specified value respectively.
c) Bounce vehicle body up and down by hand to stabilize suspen-
sion.
d) Carry out one driver aboard.
Driver's weight: 75 kg (165 lb)
Adjustment
1) Check to see if hot spot (high intensity zone) of each main (low)
beam axis falls as illustrated.
Clearance ªHº: Approx. 130 mm (5.15 in.)
2) If headlight aiming is not set properly, align it to specification by
adjusting aiming screw and aiming gear.