1998 SUZUKI GRAND VITARA Clutc

YH4
GRAND
VITARA
1B-54 AIR CONDITIONING (OPTIONAL)
2
4) Remove shims from shaft.
5) Using special tool (C), remove circlip.
Special Tool
(C): 09900-06107
6) Remove clutch coil lead wire clamp screw, and remove clutch
coil read wire ground terminal.
7) Remove clutch pulley with puller (1) from compressor (2).
NOTE:
Be careful not to damage pulley when tapping magnet
clutch assembly.
8) Remove clutch coil.
Special tool
(C): 09900-06107
INSTALLATION
1) Install clutch coil (2).
Protrusion on under side of coil ring must match hole in com-
pressor (3) to prevent movement ant correctly locate lead wire.
2) Using special tool (C), install snap ring (1) as shown.
Special Tool
(C): 09990-06107
3) Install clamp portion and ground terminal of lead wire.

YH4
GRAND
VITARA
AIR CONDITIONING (OPTIONAL) 1B-55
1. Armature plate
4) Clutch pulley (1).
(1) Set clutch pulley squarely over clutch pulley installation boss.
(2) Place special tool (D) onto clutch pulley bearing.
Ensure that edge rests only on inner race of bearing.
(3) Install snap ring.
Special Tool
(D): 09991-06010
CAUTION:
Be careful not to scratch bearing seal.
5) Adjust clearance, between clutch plate (1) and clutch pulley by
putting shim on compressor shaft.
Standard clearance ªaº: 0.3 ± 0.5 mm (0.012 ± 0.02 in.)
6) Tighten new clutch plate bolt as specified below.
Tightening Torque
(a): 14 N
.m (1.4 kg-m, 10.5 lb-ft)
Special Tool
(A): 09991-06020

YH4
GRAND
VITARA
1B-56 AIR CONDITIONING (OPTIONAL)
1. Clutch plate bolt
2. Clutch plate
3. Circlip
4. Clutch pulley
5. Washer
6. Shim
7. Oil felt ring
8. Clutch coil
9. Lip type seal
10. Compressor front head
11. Compressor body component
12. O-ring
13. Compressor thermal switch
3. Washer
(if equipped)1. Thermal switch
2. Ohmmeter
MAGNET CLUTCH ASSEMBLY (FOR SEIKO SEIKI)
INSPECTION
MAGNET CLUTCH

Inspect clutch plate and clutch pulley for signs of oil.

Check clutch pulley bearings for noise and grease leakage.

Using and ohmmeter, measure resistance of clutch coil between
clutch coil lead wire (1) and compressor body.
If measured resistance is not within tolerance, replace coil.
Standard resistance: 2.5 ± 4.5
at 20C, 68F
COMPRESSOR THERMAL SWITCH
Use an ohmmeter to check thermal switch for continuity. If there is
no continuity, replace it.
REMOVAL
1) Remove compressor assembly from vehicle. Refer to COM-
PRESSOR ASSEMBLY in this section.
2) Fix clutch plate (1) with special tool (A) and remove clutch plate
bolt (2).
Special Tool
(A): 09991-06020
NOTE:
Do not reuse armature plate nut.

YH4
GRAND
VITARA
AIR CONDITIONING (OPTIONAL) 1B-57
3) Using special tool (B), remove clutch plate (1).
Special Tool
(B): 09991-06030
4) Disconnect clutch coil lead wire from compressor thermal switch
led wire.
5) Remove felt ring (if equipped) and shims from shaft.
6) Using special tool (C), remove circlip.
Special Tool
(C): 09900-06107
7) Remove clutch coil lead wire clamp screw.
8) Remove clutch pulley with puller (1) from compressor (2).
NOTE:
Be careful not to damage pulley when tapping magnet
clutch.
9) Remove clutch coil.
INSTALLATION
1) Install clutch coil (2).
Protrusion on under side of clutch coil must match hole in com-
pressor (3) to prevent movement ant correctly locate lead wire.
2) Using special tool (C), install snap ring (1) as shown.
Special Tool
(C): 09990-06107
3) Clamp covering portion of lead wire.

YH4
GRAND
VITARA
3. Washer
(if equipped)
1B-58 AIR CONDITIONING (OPTIONAL)
4) Install clutch pulley (1).
(1) Set clutch pulley squarely over clutch pulley installation boss.
(2) Place special tool (D) onto clutch pulley bearing.
Ensure that edge rests only on inner race of bearing.
(3) Install snap ring.
Special Tool
(D): 09991-06010
CAUTION:
Be careful not to scratch bearing seal.
5) Adjust clearance, between clutch plate and clutch pulley (2) by
putting shim on compressor shaft.
Standard clearance ªaº: 0.3 ± 0.6 mm (0.012 ± 0.024 in.)
6) Tighten new clutch plate (1) bolt (2) as specified below.
Tightening Torque
(a): 14 N
.m (1.4 kg-m, 10.5 lb-ft)
Special Tool
(A): 09991-06020

YH4
GRAND
VITARA
AIR CONDITIONING (OPTIONAL) 1B-59
PUSH
3. Cylinder
4. Case
5. O-ring
2. Bearing puller
LIP TYPE SEAL (FOR SEIKO SEIKI)
REMOVAL
1) Remove magnet clutch assembly, referring to ªMAGNET
CLUTCH ASSEMBLYº in this section.
2) Remove compressor front head (1) mounting bolt (10 pcs.).
3) Remove compressor front head (1) by pushing cylinder shaft
(2).
NOTE:
Be careful not to remove cylinder from case.
4) Remove O-ring.
5) Remove lip seal from compressor front head (1).
INSTALLATION
1) Press-fit lip seal (1) into compressor front head (2) using special
tool (E).
Special Tool
(E): 09991-06050
CAUTION:
Do not reuse mechanical seal once removed from com-
pressor.

YH4
GRAND
VITARA
AIR CONDITIONING (OPTIONAL) 1B-61
09900-06107
Snap ring pliers
(Opening type)09991-06010
Magnet clutch pulley installer09991-06020
Armature plate spanner09991-06030
Armature plate remover
09991-06040
Lip type seal protector09991-06050
Lip type seal installer
REQUIRED SERVICE MATERIAL
MATERIALRECOMMENDED
SUZUKI PRODUCTUSE
Compressor oil for DENSO
compressor (Refrigerant oil)COMPRESSOR OIL (ND-OIL 8, 250 cc)
99000-27080
O-ring

Each component
Compressor oil for
SEIKO SEIKI compressor
(Refrigerant oil)COMPRESSOR OIL RS20 (150 cc)
99000-99088-00D
O-ring

Each component
RefrigerantREFRIGERANT DRUM (200 g)
95794-50G00
Refrigerant charge
SPECIAL TOOLS

YH4
GRAND
VITARA
7A-2 MANUAL TRANSMISSION (TYPE 1)
DIAGNOSIS
ConditionPossible CauseCorrection
Gear slipping out of mesh
Worn shift fork shaft

Worn shift fork or synchronizer sleeve

Weak or damaged locating spring

Worn bearings on input shaft or main shaft

Worn chamfered tooth on sleeve or gear

Missing or disengagement of circlip(s)Replace
Replace
Replace
Replace
Replace sleeve and gear
Install
Gears refusing to disengage
Weakened or broken synchronizer spring

Distorted shift shaft or shift forkReplace
Replace
Hard shifting
Improper clutch pedal free travel

Distorted or broken clutch disc

Damaged clutch pressure plate

Worn synchronizer ring

Worn chamfered tooth on sleeve or gear

Distorted shift shaftAdjust
Replace
Replace clutch cover
Replace
Replace sleeve and gear
Replace
Noise
Inadequate or insufficient lubricant

Damaged or worn bearing(s)

Damaged or worn gear(s)

Damaged or worn synchronizer ring

Damaged or worn chamfered tooth on
sleeve or gearReplenish
Replace
Replace
Replace
Replace