1998 SSANGYONG MUSSO wiring

5A-96 AUTOMATIC TRANSMISSION
9. Check that the cam collar slides freely on the rod.
10. Insert the cross shaft into the case, from the side opposite
to the inhibitor switch, then install the anti-rattle spring on
the shaft.
11. Position the manual valve detent lever, aligning it with the
cross-shaft bore in the case.
12. Push the shaft through the detent lever until it starts in the
detent lever side of the case.
13. Install the detent lever drive pin in the shaft using tool No.
0555-331897 with the adaptor over the pin.
14. Press the pin into the shaft until the tool bottoms.
15. Remove the tool and fit the spring retaining circlip to the
shaft.
16. Install the new cross shaft seals using tool No. 0555-
331894.
17. Install the inhibitor switch on the case. Torque the screws
as per specifications. Press the pin into the shaft until the
tool bottoms (4WD models) using tool No.0555-332942.
18. Thoroughly check the terminal wiring loom for condition
and continuity.
19. Position the loom and locate the solenoid 7 contact and
terminal in the pump mounting flange at the front of the
case. The solenoid 7 wire is routed under the park rod
and cross shaft in the case.

AUTOMATIC TRANSMISSION 5A-97
20. Install the ten pin connector in the case engaging the tangs
on the connector in the notches in case.
4WD MODELS ONLY
21. Route the portion of the wiring loom coming out of the
case down between the inhibitor switch and the case.
Position the ten pin plug on the wiring loom bracket .

5A-116 AUTOMATIC TRANSMISSION
18. Install the gasket on the pump cover.
19. Install the cover plate, solenoid 7 with the retainer and the
solenoid wiring retainer to the pump cover, ensuring that
the periphery of the cover plate is flush with the periphery
of the pump cover. Refer to figure 8.34.
Tighten the screws to specification in the order (1-5), shown
in figure 8.44.
24. Install the pump and cover assembly over the input shaft
being careful not to damage the sealing rings. Tighten the
pump cover to case bolts to specification. Refer to figure
8.45. 20. Tighten the solenoid 7 screw. Refer to figure 8.39.
Notice
Check that neither the wiring nor the connector protrudes
excessively, in order that at assembly neither the wiring
and the connector contacts or rubs on the input shaft or
the C1/C2 clutch cylinder.
21. Assemble the pump to the pump cover.
Tighten all bolts and the crescent screw finger tight,
ensuring that the pump is flush against the pump cover.
Tighten the bolts and the screw to specification in the order
(A - F), shown in figure 8.44.
22. Install the pump to transmission case gasket onto the case.
23. Fit the ‘O’ ring to the pump cover outer diameter.Figure 8.44 - Pump Bolt Tightening Sequence
Figure 8.45 - Tightening Sequence Pump to
Case

AUTOMATIC TRANSMISSION 5A-123
23. Holding the separator plate to the upper valve body to
prevent the check balls from falling out, install the upper
valve body on the lower valve body. Install all screws finger
tight then tighten the screws to specification in the
prescribed sequence. Refer to figure 8.58.
24. Install solenoids 1,2,3,4 and 6. Ensure the solenoid is firmly
secured by the retainer and that the screw is tightened to
specification.
25. Install solenoid 5. Ensure that the solenoid is pushed firmly
into the valve body by the retainer.
Notice
The wiring loom ground wire eyelet terminal is secured
beneath the solenoid retainer.
26. Install the line pressure relief valve, tapered end first, (refer
to figure 8.59), and the spring and disc. Secure with the
retaining pin. Figure 8.58 - Tightening Sequence Upper to Lower Valve Body
Figure 8.59 - Line Pressure Relief Valve

5A-124 AUTOMATIC TRANSMISSION
27. Install the line pressure plug and tighten to specification.
Refer to figure 8.62.
28. Install the detent spring assembly (spring, support plate
and screw), ensuring that the screw is tightened to
specification. Check the spring for wear or damage.
29. Install the manual shift valve. Refer to figure 8.60.
Notice
Be aware that the manual valve will fall out of the valve
body.
Figure 8.62 - Wiring Installation
Figure 8.60 - Manual Shift Valve

AUTOMATIC TRANSMISSION 5A-125
30. Align the valve body assembly on the transmission case
and install the manual valve lever to manual valve link. Fit
the long end of the link to the manual valve first. Install the
securing bolts and tighten to specification in the specified
sequence. Refer to figure 8.61.
31. Check the alignment of the detent roller and the manual
lever quadrant.
32. Connect the solenoid wiring as detailed below:
lSolenoid 1 - red
lSolenoid 2 - bIue
lSolenoid 3 - yellow
lSolenoid 4 - orange
lSolenoid 5 - green
lSolenoid 6 - violet (Refer to figure 8.62.)
Notice
All hardware must be correctly installed and torqued to
specification.
Figure 8.61 - Tightening Sequence Valve Body to Case

MANUAL TRANSMISSION 5B-15
Removal & Installation Procedure
1. Disconnect the negative terminal from the battery.
2. Lift up the vehicle and fix it safely.
3. Remove the drain plug from the transmission housing and
drain the oil. Reinstall the drain plug.
Installation Notice
Tightening Torque
25 Nm
4. Disconnect the back-up switch connector.
5. Remove the breather hose.
6. Remove the speedometer connector and other wiring
harnesses and connectors.

TRANSFER CASE (PART TIME 4408) 5D1-3
Cannot Front Wheel Drive when Shifted 4H,4L
DIAGNOSIS
Electric Shift Problems
Action
Overhaul and check, replace if necessary.
Overhaul and check for wear and damage.
Replace if necessary.
Check sliding parts, replace if necessary. Checks
Faulty or Damaged TCCU, Speed Sensor, Motor, Clutch
or Internal Wirings
Damaged or Worn Shift Cam, Hub, Fork and Rail Shift
Binding Shift Fork, Hub Collar or Gear
Checks
Broken Drive ChainAction
Check sliding parts, replace if necessary.
Noise in 4WD Operation
Checks
Improper or low oil
Loosened bolts or mounted parts
Noisy T/C bearing
Noisy gearsAction
Drain and replace with specified oil.
Retighten as specified.
Disassemble bearings and parts and check for wear or
damage. Replace if necessary.
Check for wear and damage including speedometer
gear, replace if necessary.
Noise in 4H or 4L
Checks
Worn or Damaged Sprockets or Drive Chain
Incorrect Tire PressureAction
Disassemble and check for wear and damage, replace
if necessary.
Adjust tire pressure.
Transfer Case Oil Leakage
Action
Replace the case.
Clean case and parts and check for leakage.
Remove breather hose and clean, replace if necessary.
Use specified oil and adjust oil level.
Retighten
Use specified sealant and retighten.
Replace Checks
Cracked Transfer Case
Leakage from Other Parts
Breather Clogging
Improper or too much Oil
Loosened Sealing Bolts
Improperly Applied Sealant
Worn or Damaged Oil Seal