1998 SSANGYONG MUSSO fuel

1B3-16 OM600 ENGINE MECHANICAL
16. Remove the power steering pump lines.
Notice
Completely drain the fluid.
17. Disconnect the fuel feed line with prefilter from the feed
pump on injection pump.
18. Vehicle with automatic transmission.
Remove the hydraulic lines (19, 20) from oil cooler (2).
19. Disconnect the engine harness.
20. Disconnect the preheating time relay cable.

OM600 ENGINE MECHANICAL 1B3-17
26. Disconnect the starter motor wires and remove the starter
motor.
21. Remove the fuel lines from the fuel filter and cover the
filter with plug.
22. Disconnect the brake booster hose from vacuum pump.
23. Disconnect the other vacuum lines.
24. Disconnect the ground cable.
25. Disconnect the alternator wires.

OM600 ENGINE MECHANICAL 1B3-29
1 Threaded Ring........................................130 Nm
2 Prechamber
PRECHAMBER
Preceding Work : Removal of glow plug
Removal of fuel injection nozzle
3 Cylinder Head

OM600 ENGINE MECHANICAL 1B3-37
CYLINDER HEAD
1 Fuel Injection Pipe.....................................18Nm
2 Cylinder Head
3 Gasket ................................................... Replace
4 Bolt............................................................25Nm
5 Washer
6 Clamp
7 Heater Feed Pipe
8 Bolt
9 Washer
1 0 Bolt
11 Nozzle Washer....................................... Replace
12 Fuel Injection Nozzle............................35-40 Nm
13 Hexagon Socket Bolt................................. 25 Nm
14 Washer
1 5 Bolt........................................................... 25 Nm
16 Cylinder Head Bolt..............................See Table
17 Cylinder Head Cover
1 8 Bolt........................................................... 10 Nm
19 Gasket
2 0 Camshaft21 Camshaft Drive Sprocket....................... Replace
22 Washer
23 Bolt(12-Sided) ..................................25Nm + 90°
24 Sliding Rail
25 Sliding Rail Pin
26 Sliding Rail Pin
27 Chain Tensioner....................................... 80 Nm
28 Gasket ................................................... Replace
29 Cooling Fan.............................................. Check
30 Hexagon Socket Bolt................................. 45 Nm
31 Tensioning Lever
3 2 Bolt........................................................... 25 Nm
3 3 Bolt
34 Nut ............................................................ 23 Nm
35 Fuel Filter
36 Turbo Charger
37 Intake Duct
38 Gasket ................................................... Replace
39 Intake Manifold

1B3-42 OM600 ENGINE MECHANICAL
14. Pull out the accelerator control linkage.
15. Remove the fuel injection line(1) from the fuel injection
nozzle(12).
Box Wrench Inset 000 589 77 03 00
16. Remove the fuel injection line from the fuel injection pump.
Box Wrench Insert 000 589 77 03 00
17. Remove the bracket mounting bolts and then remove the
fuel injection line(1).

OM600 ENGINE MECHANICAL 1B3-45
26. Disconnect the fuel lines from the fuel filter.
27. Disconnect the fuel lines from the injection pump.
28. Remove the fuel filter(35).
29. Remove the fuel injection nozzle(12) and nozzle
washer(11).
Socket Wrench Insert 001 589 65 09 00

1B3-54 OM600 ENGINE MECHANICAL
8. Connect the vacuum lines to the vacuum pump.
9. Install the fuel filter and connect the pipe.
Tightening Torque 25 Nm
Notice
Be careful not to be confused the connections and hoses.
10. Connect the fuel pipe to the injection pump.
11. Install the sliding rail(24) and insert the sliding rail pins(25,
26).
Notice
Apply sealing compound on the each collar of the sliding
rail pins.
Sliding Hammer 116 589 20 33 00
Threaded Pin 116 589 02 34 00

OM600 ENGINE MECHANICAL 1B3-59
27. Replace the seal and then install the chain tensioner.
Tightening Torque 80 Nm
28. Remove the engine lock.
29. Insert the nozzle washer into the hole to face round part
downward.
30. Install the fuel injection nozzle.
Tightening Torque 40 Nm
31. Connect the fuel hose.
32. Install the cable channel and connect the cables to glow
plugs.