1998 SSANGYONG MUSSO wheel bolts

5D2-44 TRANSFER CASE (TOD)
9. Remove the bolts that retain the front case to the
rear case. Make sure that the front case is facing
downward so that the rear cover is facing upwards.
Pry on the bosses and separate the front case from
the rear case. Remove all traces of gasket sealant
from the mating surfaces of the front case and rear
case.
10. If the speedometer drive gear is to be replaced, first
remove the flange seal by prying and pulling the
curved-up lip of the flange seal. Do not damage the
bearing, bearing cage or case. Remove and discard
the flange seal. Remove the speedometer drive gear
and upper tone wheel.
69 Yoke to Flange Seal
75 Snap Ring
76 Bearing
77 Speedometer Drive Gear
79 Upper Tone Wheel
40 Clutch Coil
40a Clutch Coil Retaining Bolts
40b Wire
11. If the rear output shaft bearing requires replacing, remove
the internal snap ring that retains the bearing in the bore.
From the outside of the case, drive out the bearing.
12. Remove the three nuts and washers retaining the clutch
coil assembly to the rear case. Pull the assembly, along
with the O-ring and wire, from the case.
13. Remove bearing assembly from output shaft.
Remove the clutch housing from the output shaft.
Remove the balls and apply cam and wave washer from
the output shaft.
Remove snap ring from output shaft. Remove clutch pack
assembly from output shaft.
25 Ball
26 Cam and Coil Assembly

TRANSFER CASE (TOD) 5D2-51
25. Install the pin on the tang end of the helical cam into the
hole in the front case. Position the torsion spring tangs so
that they are pointing toward the top side of the transfer
case and just touching the high-low shift fork.
CAUTION
Do not bend the helical cam during installation to the front
case because of possible damage to the pin at the tang
end of the motor shaft.
26. Install the shift rail through the high-low shift fork and make
sure that the reverse gear shift rail is seated in the front
case bore.
27. Install upper and lower speed sensors into the cover. Feed
the coil wire through the upper speed sensor wire shield.
28. Install upper tone wheel, speedometer gear and rear output
seal. Use Output Shaft Seal Replacer and Driver or
equivalent to install seal.
29. Coat the mating surface of the front case with a bead of
Black Non-Acid Cure Silicone Rubber or equivalent.
30. The following procedure must be followed prior to installing
the rear case onto the front case half:
a. Align the output shaft with the rear case output shaft bore.
b. Align the helical cam with the rear case motor bore.
If difficulty is encountered with seating the rear case, tap
the rear output shaft with a sharp blow using a rubber
mallet in a direction away from the triangular shaft while
pushing down on the rear case.
Tightening Torque 25 - 37 Nm 31. Install the bolts retaining the case halves and tighten.

6A-2 POWER STEERING SYSTEM
Checks
Damaged or Binding Steering Ball Joint
Improper Preload of Steering Pinion
Damaged Wheel or Tire
Faulty Suspension SystemChecks
Worn Steering Gear
Worn or Damaged Steering Ball Joint
Loosened Steering Gearbox BoltsChecks
Damaged Steering Linkage
Damaged Wheel and Tire
Faulty Brake System
Faulty Suspension SystemChecks
Lack of Lubrication
Abnormal Wear or Binding of Steering Ball Joint
Damaged or Faulty Steering Gear
Improper Preload of Steering Pinion
Faulty Steering Shaft Joint
Steering Fluid Leaks
Lack of Fluid or Air-in System
Faulty Steering Oil Pump
Damaged or Loosened Pump Drive Belt
Clogging Oil Line
Damaged Wheel or Tire
Faulty Suspension System
DIAGNOSIS
HARD STEERING
Action
Lubricate
Replace
Replace gear assembly
Adjust
Replace
Repair or replace
Replenish or bleed
Replace
Adjust or replace
Repair or replace
Repair or replace
Repair or replace
STEERING PULLS TO ONE SIDE
Action
Repair
Repair or replace
Repair or replace
Repair or replace
EXCESSIVE WHEEL PLAY
Action
Replace gear assembly
Replace
Retighten
POOR RETURN OF STEERING WHEEL
Action
Replace
Replace gear assembly
Repair or replace
Repair or replace

6E-4 STEERING WHEEL AND COLUMN
6. Disconnect each connectors.
7. Remove the vacuum hose from the ignition switch(Diesel
only) .
9. Remove the lower shaft by removing the bolt of the steering
column shaft.
Installation Notice
Tightening Torque 9 - 14 Nm
8. Remove the combination switch assembly.
10. Remove the dash panel mounting bolts.
Installation Notice
Tightening Torque 30 - 40 Nm

8B-18 SUPPLEMENTAL RESTRAINT SYSTEM(SRS)
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
AIR BAG MODULE
Removal & Installation Procedure
1. Remove the steering wheel rid (LH,RH) with a screwdriver.
Installation Notice
Each position mark (LH,RH) is stamped on the inner surface
of the rids.
Tightening Torque 7 - 11 Nm
3. Disconnect the connectors and remove the air bag module.
4. Installation should follow the removal procedure in the
reverse order. 2. Unscrew the bolts from both sides.
Installation Notice