1998 SSANGYONG MUSSO service

Application
Engine Type
Displacement (CC)
Cylinder (Bore x Stroke) (mm)
Fuel Injection / Ignition System
Compression Ratio
Number of Cylinders
Camshaft Valve Arrangement
Camshaft Drive Type
Max. Output (ps/rpm)
Max. Torque (kg•m/rpm)
Firing Order
Injection Timing
Valve Timing Intake Open/Close
(at 2mm lift) ExhaustOpen/Close
Valve Clearance Adjustment
SECTION 1
ENGINE
SECTION 1A3(OM600 ENGINE)
GENERAL ENGINE INFORMATION
TABLE OF CONTENTS
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1A3-1
Engine Specifications . . . . . . . . . . . . . . . . . . 1A3-1
Sectional View . . . . . . . . . . . . . . . . . . . . . . 1A3-3
OM662LA Engine . . . . . . . . . . . . . . . . . . . . . 1A3-3
OM661LA Engine . . . . . . . . . . . . . . . . . . . . . 1A3-5
Performance Curve . . . . . . . . . . . . . . . . . . 1A3-7
OM662LA Engine . . . . . . . . . . . . . . . . . . . . . 1A3-7
OM661LA Engine . . . . . . . . . . . . . . . . . . . . . 1A3-8
Special Tools . . . . . . . . . . . . . . . . . . . . . . . 1A3-9
SPECIFICATIONS
ENGINE SPECIFICATIONS
Special Tools Table . . . . . . . . . . . . . . . . . . . . 1A3-9
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . 1A3-10
Oil Leak Diagnosis . . . . . . . . . . . . . . . . . . . 1A3-10
Compression Pressure Test . . . . . . . . . . . . 1A3-11
Cylinder Pressure Leakage Test . . . . . . . . . 1A3-13
General Information . . . . . . . . . . . . . . . . . 1A3-15
Cleanliness and Care . . . . . . . . . . . . . . . . . 1A3-15
On-Engine Service . . . . . . . . . . . . . . . . . . . 1A3-15
OM662LA
Four-Stroke Diesel
2874
89 x 92.4
PES 5 M55 C320 RS 168
22:1
5
SOHC
Chain-Drive
120 / 4000
25.5 / 4000
1-2-4-5-3
BTDC 18°± 10°
ATDC 11.33° / ABDC 17°
BBDC 28° / BTDC 15.25°
Automatic ControlOM661LA
Four-Stroke Diesel
2299
89 x 92.4
PES 5 M55 C320 RS 167
22:1
4
SOHC
Chain-Drive
101 / 4000
21.5 / 2400
1-3-4-2
BTDC 18°± 10°
ATDC 11.33° / ABDC 17°
BBDC 28° / BTDC 15.25°
Automatic Control

GENERAL ENGINE INFORMATION 1A3-11
28bar
Approx.18bar
Max. 3bar
COMPRESSION PRESSURE TEST
1 Test Adapter
2 Flexible Connector
3 Compression Pressure Recorder
Tools Required
000 589 65 09 00 Socket
001 589 73 21 00 Hand Vacuum Pump
Service Data
Normal Compression Pressure
Minimum Compression Pressure
Permissible Pressure Difference Between Individual Cylinders
lEngine at normal operating temperature of 80°C

1A3-12 GENERAL ENGINE INFORMATION
Compression Pressure Measurement
Notice
Ensure that no gear is engaged and that the vehicle is
protected from rolling.
1. Run the engine to be the coolant temperature 80°C.
2. Remove the fuel injection nozzle.
Socket Wrench Insert 001 589 65 09 00
3. Install the test adapter (1) and connect the flexible
connector (2) to the compression pressure recorder.
Compression Pressure Recorder 001 589 76 21 00
4. Disconnect the vacuum line from the stop unit and
connect the hand vacuum pump to the stop unit.
5. Pump the hand vacuum pump and make the fuel injection
pump in stop position.
Operating PressureApprox. 500bar
Hand Vacuum Pump 001 589 73 21 00
6. Using a starter motor, crank the engine 8 revolutions.
7. Measure the remaining cylinder compression pressure
in the same manner and compare it with service data.
Notice
If out of standard, do cylinder pressure leakage test.
8. Remove the compression pressure recorder.
9. Install the fuel injection nozzle.

GENERAL ENGINE INFORMATION 1A3-15
GENERAL INFORMATION
CLEANLINESS AND CARE
An automobile engine is a combination of many
machined, honed, polished and lapped surfaces with
tolerances that are measured in the ten-thousanths
of an inch. When any internal engine parts are
serviced, care and cleanliness are important. A liberal
coating of enigne oil should be applied to friction areas
during assembly, to protect and lubricate the surfaces
on initial operation. Proper cleaning and protection
of machined surfaces and friction areas is part fo the
repair procedure. This is considered standard shop
practice even if not specifically stated.
Whenever valve train components are removed for
service, they should be kept in order. They should be
installed in the same locations, and with the same
mating surfaces, as when they were removed.Battery cables should be disconnected before any
major work is performed on the engine. Failure to
disconnect cables may result in damage to wire
harness or other electrical parts.
ON-ENGINE SERVICE
Caution: Disconnect the negative battery cable
before removing or installing any electrical unit,
or when a tool or equipment could easily come in
contact with exposed electrical terminals.
Disconnecting this cable will help prevent
personal injury and damage to the vehicle. The
ignition must also be in LOCK unless otherwise
noted.
Notice: Any time the air cleaner is removed, the intake
opening should be covered. This will protect against
accidental entrance of foreign material, which could
follow the intake passage into the cylinder and cause
extensive damage when the engine is started.

SECTION 1B1
M162 ENGINE MECHANICAL
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1B1-2
Fastener Tightening Specifications . . . . . . . . 1B1-2
Special Tools . . . . . . . . . . . . . . . . . . . . . . . 1B1-4
Special Tools Table . . . . . . . . . . . . . . . . . . . . 1B1-4
Maintenance and Repair . . . . . . . . . . . . . . 1B1-8
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 1B1-8
Engine Assembly . . . . . . . . . . . . . . . . . . . . . 1B1-8
Crankcase Ventilation System . . . . . . . . . . 1B1-16
Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . 1B1-18
Power Steering Pump and A/C Bracket . . . 1B1-19
Hydraulic Engine Mounting Insulator . . . . . . 1B1-22
Poly V-Belt . . . . . . . . . . . . . . . . . . . . . . . . . 1B1-25
Tensioning Device . . . . . . . . . . . . . . . . . . . . 1B1-27
Poly V-Belt Inspection . . . . . . . . . . . . . . . . . 1B1-29
Cylinder Head Cover . . . . . . . . . . . . . . . . . 1B1-31
Cylinder Head Front Cover . . . . . . . . . . . . . 1B1-33
Cylinder Head . . . . . . . . . . . . . . . . . . . . . . . 1B1-35
Timing Gear Case Cover . . . . . . . . . . . . . . 1B1-38
Crankshaft Sealing Rear Cover . . . . . . . . . 1B1-40
Belt Pulley and Vibration Damper . . . . . . . . 1B1-42
Crankshaft Front Radial Seal . . . . . . . . . . . 1B1-45
Crankshaft Rear Radial Seal . . . . . . . . . . . 1B1-46
Crankshaft . . . . . . . . . . . . . . . . . . . . . . . . . 1B1-47
Flywheel / Driven Plate . . . . . . . . . . . . . . . . 1B1-53
Camshaft Adjuster . . . . . . . . . . . . . . . . . . . 1B1-55
Camshaft Sprocket Bolt . . . . . . . . . . . . . . . 1B1-58
Camshaft . . . . . . . . . . . . . . . . . . . . . . . . . . 1B1-59
TABLE OF CONTENTS
Camshaft Timing Position . . . . . . . . . . . . . . 1B1-64
Valve Spring . . . . . . . . . . . . . . . . . . . . . . . . 1B1-67
Valve Stem Seal . . . . . . . . . . . . . . . . . . . . . 1B1-71
Chain Tensioner . . . . . . . . . . . . . . . . . . . . . 1B1-72
Timing Chain . . . . . . . . . . . . . . . . . . . . . . . . 1B1-75
Tensioning Rail . . . . . . . . . . . . . . . . . . . . . . 1B1-80
Cylinder Head Guide Rail . . . . . . . . . . . . . . 1B1-81
Crankcase Guide Rail . . . . . . . . . . . . . . . . . 1B1-82
Crankshaft Sprocket . . . . . . . . . . . . . . . . . . 1B1-83
Piston . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1B1-85
Connecting Rod . . . . . . . . . . . . . . . . . . . . . 1B1-88
Piston Ring . . . . . . . . . . . . . . . . . . . . . . . . . 1B1-90
Engine Oil Specification . . . . . . . . . . . . . . . 1B1-92
Oil Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1B1-93
Engine Oil and Oil Filter Element . . . . . . . . 1B1-95
Oil Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . 1B1-97
Oil Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . 1B1-99
Oil Pressure Relief Valve . . . . . . . . . . . . . 1B1-101
Oil Non-Return Valve . . . . . . . . . . . . . . . . 1B1-102
Oil Dipstick Guide Tube . . . . . . . . . . . . . . 1B1-103
Unit Repair . . . . . . . . . . . . . . . . . . . . . . . 1B1-104
Oil Gallery in Crankcase . . . . . . . . . . . . . . 1B1-104
Oil Gallery in Cylinder Head . . . . . . . . . . . 1B1-106
Core Plugs in Crankcase . . . . . . . . . . . . . 1B1-109
Cylinder Bore . . . . . . . . . . . . . . . . . . . . . . 1B1-111
Crankcase Mating Surface . . . . . . . . . . . . 1B1-113
Cylinder Head Mating Surface . . . . . . . . . 1B1-115

1B1-8 M162 ENGINE MECHANICAL
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
ENGINE ASSEMBLY
Tools Required
000 589 10 99 01 Torque Wrench
000 589 40 37 00 Hose Clamp
112 589 00 72 00 Oil Extractor

1B1-22 M162 ENGINE MECHANICAL
HYDRAULIC ENGINE MOUNTING INSULATOR
Service Data

M162 ENGINE MECHANICAL 1B1-43
Components
1 Center Bolt (M18 x 50)
2 Center Bolt Washer
3 Vibration Damper and Pulley Assembly
4 Key
5 Crankshaft Front Seal
6 Timing Gear Case Cover
7 Crankshaft Sprocket (Camshaft Driven)
8 Crankshaft Sprocket (Oil pump Driven)
9 Crankshaft
10 Oil Pan
11 Oil Pan Gasket
12 Oil Pan Mounting Bolt (M6 x 22)
Service Data Standard
Permissble Deviation of The Vibration DamperRadial Runout
Axial Runout0.6 mm
0.6 mm
Tools Required
103 589 00 33 00 Puller
001 589 65 09 00 Socket Wrench Insert
602 589 00 40 00 Engine Lock
Removal & Installation Procedure
1. Adjust the piston of number 1 cylinder to the TDC.