1998 SSANGYONG MUSSO plugs

5A-100 AUTOMATIC TRANSMISSION
Planet Carrier Assembly and Centre Support
To assemble the planet carrier assembly and centre support,
proceed as follows.
1. Check the carrier and planet assembly for any damage or
irregularity and ensure that all pinions rotate freely and
that the pinion end float is within the tolerance stated in
section 9.2.
2. Install the one way clutch (OWC) retainer to the planet
carrier with the inner edge pointing downwards. Inspect
the OWC race and the sprag assembly for wear or damage.
Replace if necessary.
3. Install the outer race in the drum. Press the race to the
bottom of the drum and install the retaining circlip. Ensure
the circlip is firmly seated in its groove.
Refer to figure 8.21.
4. Install the OWC into the outer race with the lip edge
uppermost. Lubricate the sprags with automatic
transmission fluid. Refer to figure 8.20.
5. Check that the plugs are fitted to the centre support, then
assemble the centre support into the OWC, ensuring that
the support will rotate in an anti-clockwise direction only.
Refer to figure 8.21.
Figure 8.20 - Planet Carrier Assembly and
Centre Support
6. Lubricate the No.9 needle thrust bearing and the thrust
washer with petroleum jelly and fit them to the rear face of
the planet carrier. Refer to figure 8.19.
7. Install the planet assembly and the centre support into the
case, and align the centre support mounting bolt holes.
8. Install the centre support bolts finger tight.
9. Install the circlip retainer ensuring that the circlip is
completely seated in the groove of the case.
10. Remove the centre support bolts and apply Loctite 222 or
equivalent to the threads. Install the bolts and torque to
specifications.

5A-114 AUTOMATIC TRANSMISSION
13. Install the converter clutch control valve (refer to figure
8.38), spring, plug, and ‘O’ ring.
14. Install the retaining pin. Refer to figure 8.39.
Figure 8.39 - Valve Retaining Plugs and Pins
Figure 8.38 - Converter Clutch Control Valve 12. Install the retaining pin. Refer to figure 8.39.

5D1-10 TRANSFER CASE (PART TIME 4408)
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
MAINTENANCE OF TRANSFER CASE
LUBRICANT
Oil Level Check
lClean the oil level plug and surrounding area.
lRemove the oil level plug and check whether oil is drip
out or not.
lTighten the oil level plug.
Oil Change
lClean the oil level plug and surrounding area
lPlace a suitable container under the transfer case.
lRemove the oil and tighten the drain plug.
lFill the oil through the oil level plug until oil begins to
drip out.
lTighten the oil level plug.
Cautions for oil level check and plugs tightening
lDo not use an impact wrench to remove or tighten the
oil level plug or drain plug since this will damage the
threads in the transfer case.
Tightening Torque 20 - 30 Nm

5D1-16 TRANSFER CASE (PART TIME 4408)
Disassembly Procedure

1. Holding the companion flange, remove the nut and washer
and then remove the companion flange and oil seal.
2. Remove the 2 plugs from the cover.
1 Nut
2 Washer
3 Oil Seal
4 Companion Flange
5 Plug
25 Cover
6 Bolt
7 Washer
8 Bolt
9 Sensor and Harness Bracket
10 Sensor Assembly
11 Speed Sensor
12 O-ring
13 Motor Assembly
25 Cover

1. Remove the bolt, washer,3 bolts and harness bracket.
2. Remove the sensor assembly and remove the O-ring from
the speed sensor.
3. Remove the motor assembly.

TRANSFER CASE (PART TIME 4408) 5D1-35
Companion Flange
1. Install the 2 plugs to the cover.
2. Install the companion flange, oil seal and washer.
3. Holding the companion flange, tighten the nut.
1 Nut
2 Washer
3 Oil Seal
4 Companion Flange
5 Plug
25 Cover
Notice
Apply Loctite 262 to nut before installation.
Tightening Torque 346 - 380 Nm

TRANSFER CASE (TOD) 5D2-53
40. Install the rear case flange on the output shaft. Install the
rubber seal, output shaft yoke washer and nut. Tighten
the nut.
Tightening Torque 137 - 196 Nm
41. Install the drainplug and tighten.
42. Fill the transfer case with 1.4 liters of Automatic
Transmission Fluid or equivalent.
Notice
Fluid level should be just below the filler plug hole.
Tightening Torque 19 - 30 Nm
Tightening Torque 19 - 30 Nm 43. Install the fill pulg and tighten.
44. Install the transfer case as outlined in removal and
Installation, transfer case in the section.
Notice
Make sure proper drain and fill plugs are installed if case
is replaced.