1998 SSANGYONG MUSSO mirror

9L-8 GLASS AND MIRRORS
Tightening Torque 7.7 Nm 4. Before installation, ensure that the stay bolt washer is
inserted.
5. Using suction holders, install the side glass within 5minutes
after application of sealant.

GLASS AND MIRRORS 9L-9
TAILGATE GLASS
1 Wiper Arm and Blade Assembly
2 Heating Lines3 Tailgate Trim
4 Tailgate Glass
Notice
Removal and installation is as shown in upper drawings.

9L-10 GLASS AND MIRRORS
Installation of Tailgate Glass
1. Clean the tailgate flange.
lDo not reuse a gauze over 20 times.
lSaturate the gauze in solvent (Isoprophyl alcohol).
lKeep the cleaned surface to be cleaned.
lApply body primer to the cleaned and dry flange.
- If flange is oiled or contaminated, primer can not be
applied.
2. Apply primer after cleaning of tailgate flange.
lKeep primers in a refrigerator(-2°C - +5°C).
lUse sufficiently mixed primer in a mixer over 10 minutes.
lApply primer within 2 hours after opening.
lDo not apply primers which is over its druation.
lApply evenly to the flange.
lDuration : 3 minutes - 8 hours (reapply after 8 hours).
lIf primer is applied to the body, clean off immediately
with solvent.
lBe careful not to contaminate other parts.
3. Clean the tailgate galss.
lClean the glass keeping 15mm from the edge of glass.
lDo not reuse a gauze over 20 times.
lSaturate the gauze in solvent(Isoprophyl alcohol).
lDo not touch the cleaned galss surface.
lApply glass primer to the cleaned and dry glass surface.
If glass is oiled or contaminated, primer can not be
applied.
4. Apply primer to the tailgate glass.
lUse sufficiently mixed primer in a mixer over 10 minutes.
lBe careful not to contaminate other parts due to over
application.
lDuration : 1 minute - 24 hours(reapply after 24 hours).
lNever use the primer containing deposits or floating
materials.
lDo not use primers which is over its duration.
lDo not reuse a gauze over 20 times.
lApply evenly to glass.

GLASS AND MIRRORS 9L-11
5. Apply sealant to the glass.
lTurn over the glass and apply sealant.
lUneven application of sealant may cause water leakage
after installation of glass.
lDo not touch the glass moldings and dam rubber while
applying sealant.
6. Using suction holders, install the tailgate glass within
5minutes after application of sealant.
lFix the glass with adhesive tape.
lApply sealant additionally between the quarter outer
panel and tailgate glass moldings.

9L-12 GLASS AND MIRRORS
1 Auto Dimming Room Mirror Assembly
2 Sensor (Front)
3 Sensor (Rear)
AUTO DIMMING ROOM MIRROR
Layout
4 Switch
5 Cover
6 Lamp

GLASS AND MIRRORS 9L-13
Check & Service
If reflection ratio is not adjusted automatically during night
driving when AUTO switch is pressed, check each connectors
for proper connection and power flow to the auto dimming room
mirror using multi tester.
1. Yellow (Connected to back-up lamp)
2. Blue (Ground)
3. White (Power)
Voltage Rating
Operating Current
Over CurrentDV 12V
1 A
3 A
Function
When ignition switch is turned ON, green lamp on auto dimming
mirror will turn in and glare reflection ratio will be automatically
adjusted. By positioning AUTO switch to ON, 2Sensors will
automatically adjust refection ratio after sensing rear and
surrounding brightness to reduce driver’s eye fatigue during
driving though tunnel or in night.
When OFF switch is pressed, the lamp goes out and it will be
operated as a normal rear view mirror and shift lever is
positioned in reverse, the auto dimming function will be
automatically OFF.
Specifications

9L-14 GLASS AND MIRRORS
Removal & Installation Procedure
1. Removal the room mirror cover (arrow).
2. Disconnect 3-pin connector.
3. Removal the mirror assembly.
4. Installation should follow the removal procedure in the
reverse order.