1998 SSANGYONG MUSSO check engine

1F1-32 M162 ENGINE CONTROLS
Failure
codeItemChecking method Test
stepRequirementSpecified
valuePossible cause
1 liter of fuel
supply for
max. 35
seconds· ·· ·
· Fuel pump:
- Fuel supply
ratio· Ignition:ON
- Disconnect the fuel
return pipe and
connect the host to
beaker to collect the
supplied fuel Þ 1.0· Þ 2.0
· Check the fuel line
5 - 9 A
· ·· ·
· Fuel pump:
- Current
consumption· Ignition:ON
- Remove the fuel
relay from the fuse
and relay box in
luggage
compartment and
connect the
amperemeter
between No.1 and
No.3 in relay
box(fuel pump relay
removed position)
for measuring
current consumption Þ 2.0· Fuel pump
533
Multi tester(DC current)
31

1F1-34 M162 ENGINE CONTROLS
Figure 9. Shop Made Cable Figure 10. Fuel Injector Normal Spary Pattern
Failure
codeItemChecking method Test
stepRequirementSpecified
valuePossible cause
There should
be no leaks
and later
drops from
the injector· ·· ·
· Injector:
- Leakage test· Ignition:ON
- Remove the fuel
distributor and fuel
injector with a unit. Þ 1.0
The spray
pattern of the
injector most
show in the
figure 10.
· Ignition:ON
- Connect the shop
made cable to the
injector
- Collect the spraying
fuel with a beaker
- Connect the shop
made cable to
No.21(+) and No.3
(-) terminal in test
box Þ 2.0· Injector
533
· ·· ·
· Injector:
- Function test
and spray
pattern
check
533

M162 ENGINE CONTROLS 1F1-47
3. Disconnect the vacuum hose.
4. Disconnect the circlip and remove the fuel pressure
regulator.
5. Apply the oil to O-ring lightly and then replace it.
6. Installation should follow the removal procedure in the
reverse order.
7. Check for fuel pressure and internal leaks by operating the
engine. 2. Discharge the pressure in fuel supply system by pressing
the service valve.
Removal & Installation Procedure
1. Remove the fuel pressure test connector.

M162 ENGINE CONTROLS 1F1-51
Removal & Installation Procedure
1. Discharge the fuel pressure from the fuel pressure test
connector.
2. Disconnect the battery ground cable.
3. Disconnect the vacuum hose from the fuel pressure
regulator.
4. Remove the cable guide.
5. Remove the fuel return and supply line.
Notice
lFor removal, cover around parts with cloths not to be
stained by fuel.
lIn case of checking the injector only, do not remove the
fuel return and supply line.
Installation Notice
6. Remove the six injector connectors.
7. Remove the two left and two right bolts and one center bolt
of the fuel distributor assembly from the intake manifold.
Installation Notice
Tightening Torque25 - 30 Nm
Tightening Torque 22.5 - 27.5 Nm

1F1-52 M162 ENGINE CONTROLS
8. Remove the injectors and the fuel distributor carefully.
9. Installation should follow the removal procedure in the
reverse order.
10. Check for fuel pressure and internal leakage by operating
the engine.
Fuel Pressure Test
1. Turn the ignition switch to "OFF" position.
2. Remove the fuel pressure test connector.
Vacuum Hose Connected (bar) 3.2 - 3.6
Vacuum Hose Disconnected (bar) 3.7 - 4.2
5. Replace the pressure regulator diaphragm if out of the
specification. 3. Connect the fuel pressure gauge to the fuel pressure test
connector.
4. Test the fuel pressure at idling by operating the engine.

M162 ENGINE CONTROLS 1F1-53
3. If there is no change in fuel pressure and maintain the
following pressure over 30 minutes, it is normal.
Internal Leakage Test
1. Connect the fuel pressure gauge to the fuel pressure test
connector.
2. Stop the engine for approx. 30 minutes and then check the
fuel pressure changes.
Fuel pressure
drops slowly
·Fuel leakage at the
injector
• Faulty fuel pressure
regulator's
diaphragm and O-
ring.
Fuel pressure
drops rapidly• Faulty check valve
in the fuel pump.
Possible Cause Pressure Change
Fuel Pressure(bar) 2.5
Discharging the pressure in fuel system
1. Remove the fuel pressure test connector.
Installation Notice
2. Remove the fuel pressure in fuel system by pressing the
service valve with a clean, pointy tool.
Notice
Place a cloth so that the fuel doesn't stain around.
Tightening Torque 22.5 - 27.5 Nm

M162 ENGINE CONTROLS 1F1-55
Removal & Installation Procedure
1. Remove the O-ring.
Check for damage and replace it if necessary.
2. Remove the injector bracket from the injector.
Installation Notice
Exactly seat the anti-twist lock into the square groove in
injector.
3. Separate the injector from the fuel distributor.
Inspection & Maintenance
Inspection of the Injector operation and spray pattern
1. Connect the contact box to the ECU.
2. Connect the shop made test plug to the injector and place
it into the tank.
3. Position the ignition switch to ON.
4. Connect the pin 63(+) and 69(-) of the contact box with a
test cable.
5. Check the injector spray pattern.
Notice
Replace the injector if the injector spray pattern is abnormal
or the fuel doesn't inject.
Injector Resistance Inspection
1. Remove the injector connector.
2. Measure the injector coil resistance using a resistance
tester.
Notice
Replace the injector if the measured values is out of the
specified values. Check the connector and wire connection
between the ECU and the injector if the measured values
are normal.
Specified Value
14 - 17 W

1F1-56 M162 ENGINE CONTROLS
The Injector Spray Pattern Check
1. Connect the test box (129 589 00 21 00) to the ECU.
2. Disconnect the connector from connector.
3. Disconnect the fuel distributor and injector with a unit from
engine without removing the fuel supply and return line.
Notice
Prepare the beaker for taking the poping fuel.
4. Connect either end of shop made cable to the injector.
5. Connect the other end of shop made cable to the No.21
(+:63)and No.3(-:69) terminal of the test box.
6. Turn the ignition switch to "ON" position.
7. Check the injector for normal spray pattern as shown in the
figure. Check injector for leaks or later drops.
Notice
Refer to fuel injector test of engine diagnosis in this section
for detailed information.