1998 SSANGYONG MUSSO check oil

5C-12 CLUTCH
Inspection Procedure
1. Clutch Cover
lCheck the diaphragm spring tip for wear and height
unevenness.
lCheck the pressure plate surface for wear, crack and
discoloration.
lCheck the strap plate rivet for looseness and replace
the clutch cover if loosened.
Unevenness Limit 0.8 mm
2. Clutch Disc
lCheck the facing for rivet looseness, excessive runout,
sticks, oil and grease.
lMeasure the rivet head depth.
If out limit, replace the disc.
3. Clutch Release Bearing
lThe release bearing is permanently lubricated and
requires no cleaning.
lCheck the bearing for sticks, damage, abnormal noise,
turning drag and wear.
4. Release Fork
lIf there is abnormal wear in contact point with bearing,
replace the release fork.
Wear Limit 0.3 mm

Model
Type
Gear Ratio
Oil
Manufacturer
WeightPart-Time 4408 (E)
E.S.O.F. Type
1 : 1
2.48 : 1
ATF S-3, S-4 or DEXRON II, III
1.2 L
Check : Every 15,000 km
Replace : Every 50,000 km
Borg Warner
30 kg
SECTION 5D1
TRANSFER CASE (PART TIME 4408)
TABLE OF CONTENTS
SPECIFICATIONS
GENERAL SPECIFICATIONS
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this
cable will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK
unless otherwise noted.
Specifications . . . . . . . . . . . . . . . . . . . . . . . 5D1-1
General Specifications . . . . . . . . . . . . . . . . . 5D1-1
Schematic and Routing Diagram . . . . . . . . 5D1-2
Part Time Transfer Case - 4408 . . . . . . . . . . 5D1-2
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . 5D1-3
Self-Diagnosis . . . . . . . . . . . . . . . . . . . . . . 5D1-4
System Description . . . . . . . . . . . . . . . . . . . . 5D1-4
Self-Diagnosis Test . . . . . . . . . . . . . . . . . . . . 5D1-8Diagnostic Diagram . . . . . . . . . . . . . . . . . . . 5D1-9
Maintenance and Repair . . . . . . . . . . . . . 5D1-10
On-Vehicle Service . . . . . . . . . . . . . . . . . . . 5D1-10
Maintenance of Transfer Case Lubricant . . 5D1-10
Transfer Case . . . . . . . . . . . . . . . . . . . . . . . 5D1-11
Unit Repair . . . . . . . . . . . . . . . . . . . . . . . . 5D1-14
Transfer Case . . . . . . . . . . . . . . . . . . . . . . . 5D1-14
Transfer Case Control Unit (TCCU) . . . . . . 5D1-36
High
Low
Specification
Capacity
Lubrication ApplicationDescription

TRANSFER CASE (PART TIME 4408) 5D1-3
Cannot Front Wheel Drive when Shifted 4H,4L
DIAGNOSIS
Electric Shift Problems
Action
Overhaul and check, replace if necessary.
Overhaul and check for wear and damage.
Replace if necessary.
Check sliding parts, replace if necessary. Checks
Faulty or Damaged TCCU, Speed Sensor, Motor, Clutch
or Internal Wirings
Damaged or Worn Shift Cam, Hub, Fork and Rail Shift
Binding Shift Fork, Hub Collar or Gear
Checks
Broken Drive ChainAction
Check sliding parts, replace if necessary.
Noise in 4WD Operation
Checks
Improper or low oil
Loosened bolts or mounted parts
Noisy T/C bearing
Noisy gearsAction
Drain and replace with specified oil.
Retighten as specified.
Disassemble bearings and parts and check for wear or
damage. Replace if necessary.
Check for wear and damage including speedometer
gear, replace if necessary.
Noise in 4H or 4L
Checks
Worn or Damaged Sprockets or Drive Chain
Incorrect Tire PressureAction
Disassemble and check for wear and damage, replace
if necessary.
Adjust tire pressure.
Transfer Case Oil Leakage
Action
Replace the case.
Clean case and parts and check for leakage.
Remove breather hose and clean, replace if necessary.
Use specified oil and adjust oil level.
Retighten
Use specified sealant and retighten.
Replace Checks
Cracked Transfer Case
Leakage from Other Parts
Breather Clogging
Improper or too much Oil
Loosened Sealing Bolts
Improperly Applied Sealant
Worn or Damaged Oil Seal

5D1-10 TRANSFER CASE (PART TIME 4408)
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
MAINTENANCE OF TRANSFER CASE
LUBRICANT
Oil Level Check
lClean the oil level plug and surrounding area.
lRemove the oil level plug and check whether oil is drip
out or not.
lTighten the oil level plug.
Oil Change
lClean the oil level plug and surrounding area
lPlace a suitable container under the transfer case.
lRemove the oil and tighten the drain plug.
lFill the oil through the oil level plug until oil begins to
drip out.
lTighten the oil level plug.
Cautions for oil level check and plugs tightening
lDo not use an impact wrench to remove or tighten the
oil level plug or drain plug since this will damage the
threads in the transfer case.
Tightening Torque 20 - 30 Nm

5D1-22 TRANSFER CASE (PART TIME 4408)
Cleaning Procedure
Notice
Before cleaning, check the magnet for the
presence of metal particles which indicate internal
chipping of the transfer case.
1. Using cleaning solvent, clean the residual oil and dirt
deposits.
Notice
During cleaning, be careful not to damage the metal
surfaces.
2. After cleaning, dry the parts with low pressure (Max. 20 psi)
compressed air.
3. Lubricate the ball bearings and needle bearings with transfer
case oil after cleaning.
Notice
Protect the lubricated bearings from dust.
Inspection Procedure
1. Visually check the all removed parts.
Notice
Always replace the hose coupling, O-ring and oil seal with
new parts.
2. Inspection Terms
lBurr : Local rise of material forming protruding sharp
edge
lChip : An area from which a small fragment has been
broken off or cut
lCrack : Surface break of line nature indicating partial or
complete separation of material.
lExcessive wear : Heavy or obvious wear beyond
expectations considering conditions of operation.
lIndentation : Displacement of material caused by localized
heavy contact.
lGalling : Breakdown of metal surface due to excessive
friction between parts. Particles of the softer material
are torn loose and welded to the harder material.
lNick : Local break or notch, usually displacement of
material rather than loss.
lScoring : Tear or break in metal surface from contact
under abnormal pressure.
lStep wear : Heavy wear that produces a step that can
be seen or felt between adjacent contact and noncontact
surfaces.
lUneven wear : Condition of localized, unevenly distributed
wear Includes hollows, shiny spots, uneven polish and
other visual indications.

TRANSFER CASE (TOD) 5D2-25
Error in electro - magnetic clutch : fault code
“1721”, “1722”
lPhenomenon
1. Upon diagnosis by SCAN-100, it displays on fault
codes “1721,1722”.
lCause
1. Defect in electro - magnetic clutch
2. Defect in connector or wiring
- Open or short from EMC to the supply : 1721
- Short EMC to ground : 1722
Ye s
No
C1
Ye s
No Ye s
No
11-15Vdc
Ye s
No
C2
Ye s
No
Test Stage / ContentsResult
Stage Test Contents and ProcedureSpecified Value
/Yes/NoCountermeasure
Check relevant connector connection status.
1. Check relevant connector connection status with TOD
control unit.
- Does it connect correctly ?
2. Check connection status of speed sensor and clutch
coil connector (7 pin) in transfer case.
- Does it connect correctly ?
3. In case of bad connection, connect it correctly then
perform the follows :
a. Delete the memorized fault code in control unit with
Scan - 100.
b. Ignition “OFF”.
c. Ignition “ON”.
d. Diagnose by SCAN-100
- Does it display on fault codes “1721,1722” ?
Check supply voltage into electro-magnetic clutch.
1. Ignition “ON”
2. Measure voltage between pin 4/19(+) and 17/18(-) in
TOD control unit connector.
- Specified value
- Measured value is within specified range ?
3. If the specified value would not be measured, perform
the follows :
a. Check battery voltage (charging condition)
b. Check open circuit on No.13 fuse (20A)
c. Check relevant wires.
- Is the above 3a, 3b, 3c normal ?Perform C1-2 stage
Perform C1-3 stage
Perform C2 stage
Normal system Perform C2 stage
Perform C1-3 stage
Perform C3 stage
Perform C2-3 stage
Perform C3 stage
lCharging/
Replace battery
lReplace fuse
lRepair wires

TRANSFER CASE (TOD) 5D2-27
Defect in speed sensor : fault code 1731, 1732,
1733, 1734, 1735,1736
lPhenomenon
1. Upon diagnosis by SCANNER, it displays on fault code
1731, 1732, 1733, 1734, 1735 and 1736.
2. “4WD CHECK” lamp illuminates continuously when
ignition “ON”.
lCause
1. Defect of speed sensor (front, rear).
2. Defect of power supply.
4.75-5.25Vdc
Ye s
No D1
Ye s
No
D2
Ye s
Ye s
Ye s
No D3Test Stage / Contents
Result
Stage Test Contents and ProcedureSpecified Value
/Yes/NoCountermeasure
Check power supply of speed sensor.
1. Ignition “ON” or driving mode
2. Measure supply voltage between pin 16 (+) and 13 (-) in
TOD control unit connector using digital multi-tester.
- Specified value
- Measured value is within specified range ?
Check connection status of connector.
1. Check connection status of speed sensor/clutch coil
connector and TOD control unit connector.
- Does it connect correctly ?
2. In case of bad connection, connect it correctly then
perform the follows:
a. Delete the memorized fault code in control unit by
SCANNER.
b. Ignition “OFF”.
c. Ignition “ON”.
d. Diagnose by SCANNER.
- It does not display fault code.
- It displays one or more fault code among 1731 to
1736.
Check output wave of front and rear speed sensor.
1. Upon driving mode.
2. Check output wave of each speed sensor by SCANNER.
3. Is it normal on output wave ?Perform D3 stage
Perform D2 stage
Perform D3 stage
Perform D2-2 stage
Normal system
Perform D3 stage
Perform D4 stage
Replace speed
sensor then
perform D2-2 stage

5D2-40 TRANSFER CASE (TOD)
REPLACEMENT OF OIL
Oil Specification
Specified Oil Level
SpecificationStandard
Capacity
ServiceA.T.F S-3, S-4 or Dexron II, III
1.4 Litre
Inspection every 15,000km, Replacement every 50,000km=
Oil Replacement
1. Lift on vehicle then make sure on safety.
2. Prepare a vessel to drain transfer case oil.
3. Release filler plug.
4. Drain oil completely.
5. Wash drain plug and than tighten.
Installation Notice
Tightening Torque 19 - 30 Nm
6. Replenish standardized oil by specified level through filler
plug hole.
7. Tighten filler plug after washing.
Installation Notice
8. Check oil leakage.
Tightening Torque 19 - 30 Nm
.
.