1998 SSANGYONG MUSSO lock

1F3-46 OM600 ENGINE CONTROLS
Tools Required
000 589 77 03 00 Box Wrench Insert
601 589 00 08 00 Flange
601 589 05 21 00 Locking Screw
601 589 05 14 00 Assembly CageRemoval
FUEL INJECTION PUMP
Preceding Work : Removal of vacuum pump
Removal of air cleaner housing
Removal of intake manifold
18 Chain Tensioner.........................................80Nm
1 9 Seal....................................................... Replace
20 Bolt(Left-Hand Thread)..............................46Nm
21 Washer
2 2 Bolt............................................................23Nm
2 3 Seal....................................................... Replace24 Oil Pan
25 Fuel Injection Pump
2 6 Seal....................................................... Replace
27 Screw Plug.................................................30Nm
28 Square Nut

OM600 ENGINE CONTROLS 1F3-49
Installation Procedure
1. Remove the screw plug (27) and seal (26) and collect oil in
a vessel.
2. Insert flange (31) onto the injection pump camshaft and
turn until the cam of the governor is visible in the hole.
Flange 601 589 00 08 00
3. Tighten the locking screw.
Locking Screw 601 589 05 21 00
4. Ensure that the No.1 cylinder is positioned at ATDC 15°.

1F3-50 OM600 ENGINE CONTROLS
10. Connect the fuel pipes
Notice
Replace the seal.
Box Wrench Insert 000 589 77 03 00
Return Line
Fuel Injection Line
Fuel feed Line
Suction and Pressure Line46 Nm
18 Nm
13 Nm
13 Nm
5. Coat the new seal (23) with engine oil and install it.
6. Insert the fuel injection pump (25) and tighten the bolts
(22).
7. Remove the locking screw (32).
Tightening Torque 23 Nm
8. Tighten the bolt(12).
9. Insert the washer (21) and tighten the bolts (20) and then
remove the assembly cage (29).
Tightening Torque 23 Nm
Tightening Torque 46 Nm

SECTION 1G3
OM600 ENGINE INTAKE & EXHAUST
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1G3-1
Fastener Tightening Specifications . . . . . . . . 1G3-1
Schematic and Routing Diagrams . . . . . . . 1G3-2
EGR Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . 1G3-2
Maintenance and Repair . . . . . . . . . . . . . . 1G3-3
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . 1G3-3
TABLE OF CONTENTS
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Application
Air Cleaner Housing Cover Nut
Intake Manifold Bolt (M8 x 20)
Intake Manifold Bolt (M8)
Exhaust Mainfold Stud Bolt
Exhaust Pipe Nut (Engine)
Exhaust Pipe BoltN
· ·· ·
·m
9 - 11
22.5 - 27.5
22.5 - 27.5
9.5 - 12.5
15 - 28
28 - 47
Air Cleaner and Inlet Duct & Hose . . . . . . . . 1G3-3
Intake and Exhaust Manifold . . . . . . . . . . . . . 1G3-5
Turbocharger . . . . . . . . . . . . . . . . . . . . . . . 1G3-8
Charge Air System Diagram . . . . . . . . . . . . . 1G3-8
Intercooler . . . . . . . . . . . . . . . . . . . . . . . . . . 1G3-9
Turbocharger Assembly . . . . . . . . . . . . . . . 1G3-11

2B-2 WHEEL ALIGNMENT
DIAGNOSIS
TIRE DIAGNOSIS
Irregular and Premature Wear
Irregular and premature tire wear has many causes.
Some of them are incorrect inflation pressures, lack of
regular rotation, poor driving habits, or improper wheel
alignment.
Rotate the tires if :
lThe front tire wear is different from the rear.
lThe left and right front tire wear is unequal.
lThe left and right rear tire wear is unequal, Check
wheel alignment if :
lThe left and right front tire wear is unequal.
lThe wear is uneven across the tread of either front
tire.
lThe front tire treads are scuffed with “feather” edges
on the side of the tread ribs or blocks.
Tread Wear Indicators
The original equipment tires have built-in tread wear
indicators to show when the tires need replacement.
These indicators appear as bands when the tire tread
depth becomes shallow. Tire replacement is
recommended when the indicators appear in three or
more grooves at six locations.
Radial Tire Waddle
Waddle is side-to-side movement at the front or rear of
the vehicle. It is caused by the steel belt not being straight
within the tire, or by excessive lateral runout of the tire
or wheel.
The vehicle must be road tested to determine which end
of the vehicle has the faulty tire. The rear end of the
vehicle will shake from side to side or “waddle” if the
waddle tire is on the rear of the vehicle. From the driver’s
seat, it feels as though someone is pushing on the side
of the vehicle. If the faulty tire is on the front of the vehicle,
the waddle is more visual. The front sheet meld appears
to be moving back and forth, and the drivers seat feels
like the pivot point in the vehicle.
Waddle can be diagnosed using the method of
substituting known good tire and wheel assemblies on
the problem vehicle
1. Road test the vehicle to determine if the waddle is
coming from the front or the rear of the vehicle.
2. Install good tires and wheels from a similar vehicle in
place of those on the offending end of the problem
vehicle. If the source of the waddle is not obvious,
change the rear tires.

M/T
M/T
A/T (MB)
M/T
A/T (BTRA)
M/T
A/T (BTRA)
M/T
A/T (MB)
M/T
A/T (MB)
A/T (BTRA)
M/T
A/T (MB)
A/T (BTRA)
SECTION 3A
FRONT DRIVE AXLE
TABLE OF CONTENTS
SPECIFICATIONS
GENERAL SPECIFICATIONS
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 3A-1
General Specifications . . . . . . . . . . . . . . . . . . 3A-1
Fastener Tightening Specifications . . . . . . . . . 3A-2
Component Locator . . . . . . . . . . . . . . . . . . . 3A-3
Front Axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3A-3
Auto-Locking Hub . . . . . . . . . . . . . . . . . . . . . . 3A-4
Vacuum Circuit . . . . . . . . . . . . . . . . . . . . . . . . 3A-5
Maintenance and Repair . . . . . . . . . . . . . . . 3A-6
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 3A-6
Vacuum Line . . . . . . . . . . . . . . . . . . . . . . . . . . 3A-6
Steering Knuckle and Drive Shaft . . . . . . . . . . 3A-8
Front Axle . . . . . . . . . . . . . . . . . . . . . . . . . . . 3A-14
Unit Repair . . . . . . . . . . . . . . . . . . . . . . . . . 3A-16
Axle Housing . . . . . . . . . . . . . . . . . . . . . . . . . 3A-16
Application
Drive Shaft Type
Axle Housing Type
Differential Type
Differential Gear
CV Joint
Build - up
Conventional
Hypoid Gear
4.56
4.56
3.73
4.56
5.38
4.27
4.89
4.89
4.55
4.55
4.55
5.86
3.73
3.73
4.89
1.4 L
SAE 80W/90, API GL - 5
Description
661NA
662NA
661LA
662LA
E20
E23
E32 Reduction Ratio
Oil Capacity
Oil Specification

3A-2 FRONT DRIVE AXLE
FASTENER TIGHTENING SPECIFICATIONS
Steering Knuckle and Drive Shaft
Application
Drive Shaft to Front Axle Inner Shaft
Wheel Speed Sensor
Drive Shaft Cover Bolt
Locking Hub Washer Screw
Hub Flange Bolt
Hub NutNlm
25 - 35
85 - 105
50 - 60
2 - 4
70 - 90
15

FRONT DRIVE AXLE 3A-3
1 Drive Shaft
2 Axle Housing Mounting Bolt
3 Axle Housing
4 Cross Member
COMPONENT LOCATOR
FRONT AXLE
5 Brake Disc
6 Hub-Wheel
7 Locking Hub