1998 SSANGYONG MUSSO battery

5D1-12 TRANSFER CASE (PART TIME 4408)
Removal & Installation Procedure
1. Disconnect the negative terminal from the battery.
2. Lift up the vehicle and fix it safely.
3. Remove the drain plug and drain the oil.
Reinstall the drain plug.
* If planar damper is installed, unscrew 4 bolts and remove
the planar damper.
Installation Notice
Tightening Torque 19 - 30 Nm
4. Remove the breather hose.
5. Disconnect the speedometer cable connector and other
cable connectors and wiring harnesses.
6. Support the transfer case with jack and remove the front
and rear propeller shafts from the transfer case.
Installation Notice
Front
Rear81 - 89 Nm
70 - 80 NmTightening Torque

5D2-6 TRANSFER CASE (TOD)
Input/Output diagram
TOD control unit and main wiring harness is linked by 30 pin
connector. Each pin joins with switche and actuator whose
details refer to the below diagram.
Battery Power
Ignition ON/OFF
Position Encoder 1
Position Encoder 2
Position Encoder 3
Position Encoder 4
4H / 4L Switch Signal
A/T “N” Position Signal
Speed / TPS Supply
Front Speed Sensor Input
Rear Speed Sensor Input
ABS Operation Signal
Brake Switch Signal
4
5
27
10
28
30
9
24
16
11
29
25
26
19
CAN H
CAN L
Shift Motor output port
(LO-HI)
Shift Motor output port
(HI-LO)
EMC
'4L' Indicator
Position Return
'4WD CHECK' IND
TPS/speed Sensor Ground
(Speed / TPS Return)
2
1
3
21
6
7
13 15
14
K-Line20 22
23
17
18

TRANSFER CASE (TOD) 5D2-7
1. K-LINE : Communication line for coding and diagnosis with SCANNER.
Classification of Pin No.
ClassificationPin No. Pin NameDescription
Power Supply17,18Ground
TOD control unit ground
4,19Battery
TOD control unit battery supply : (Fuse No 13,20A)
5IgnitionIgnition ON / OFF
27Position 1
Position encoder 1 : check of shift motor position
10Position 2
Position encoder 2 : check of shift motor position
28Position 3
Position encoder 3 : check of shift motor position
30Position 4
Position encoder 4 : check of shift motor position
94H/4L SwitchTransfer case mode input
24Auto T/M Neutral
Check of neutral gear position in Auto T/M
16Speed5V supply (TPS / speed sensor)
11Front Speed
Front speed sensor signal input Signal Input
29Rear Speed
Rear speed sensor signal input
25ABS Operation
ABS ON / OFF
6Position Return
Position encoder ground
13Speed / TPS ReturnGround for speed sensor / TPS
22CAN-LCAN bus low line
23CAN-HCAN bus high line
2,15Motor LO-HIMotor output port
- LO to HI : join with battery
- HI to LO (or motor brake) : join with ground
1,14Motor HI-LO
Motor output port
- HI to LO : join with battery
- LO to HI (or motor brake) : join with ground
3EMCTOD output
Signal Output
214L IlluminationIlluminates “4L” indicator
7Diagnosis Display
4WD check lamp illuminator
- Upon defect ; Ground circuit
20K-LINE1)Diagnosis

5D2-12 TRANSFER CASE (TOD)
Pin
1
2
3
4
5
6
7
8Function
Motor HI-LO
Motor LO-HI
EMC
Battery (+)
Ignition
Position Return
Diagnosis Display
-Pin
9
10
11
12
13
14
15
16Function
HI / LO Switch
Position 2
Front Speed
TPS Supply (Diesel)
Speed/TPS Return
Motor HI-LO
Motor LO-HI
Speed ReferencePin
17
18
19
20
21
22
23
24Function
Ground
Ground
Battery (+)
K-LINE
4L Illumination
CAN-H
CAN-L
Auto T/M, NeutralPin
25
26
27
28
29
30
-
-Function
ABS Input
Brake Switch
Position 1
Position 3
Rear Speed
Position 4
-
-
TOD CONTROL UNIT
Shape and function of TOD Control Unit

TRANSFER CASE (TOD) 5D2-17
Classification
TCCU
EMC
Speed Sensor
Shift Motor
Position Encoder
DIAGNOSTIC TROUBLE CODES
(DTC’S)
1. Diagnostic Trouble Code Retention
The first time a fault is detected a DTC is stored in the TCCU’s
Non-Volatile memory. This DTC will remain in memory until
the TCCU is instructed to erase DTC’s by SCAN-100. DTC’s
will not be erased by disconnecting power to the TCCU.
2. Diagnostic Trouble Code Assignments
Code
1714
1715
1716
1721
1722
1731
1732
1733
1734
1735
1736
1741
1742
1743
1750
1751
1752
1753
1754Description
EEPROM Checksum Fault
TPS Loss of Signal
TPS Out of Range
EMC Open / Short to Battery
EMC Short to ground
Front Speed Sensor Voltage Low
Front Speed Sensor Voltage High
Rear Speed Sensor Voltage Low
Rear Speed Sensor Voltage High
Speed Sensor Reference Voltage Low
Speed Sensor Reference Voltage High
Motor Open / Shorted to Battery
Motor Output Shorted to Ground
Shift System Timeout
General Position Encoder Fault (Invalid Code)
Position 1 Shorted to Ground
Position 2 Shorted to Ground
Position 3 Shorted to Ground
Position 4 Shorted to Ground

TRANSFER CASE (TOD) 5D2-21
DIAGNOSIS
Malfunction interior TOD control unit ; fault code
1714
lPhenomenon
1. When ignition “ON”, “4WD CHECK” lamp illuminates
continuously.
2. On diagnosis by SCAN-100, it displays fault code “1714”.
lCause ; Error of EEPROM checksum in TOD control unit
Test Stage / Contents
Result
Stage Test Contents and ProcedureSpecified Value
/Yes/NoCountermeasure
Check power supply for TOD control unit.
1. Disconnect 30 pin connector from TOD control unit.
2. Ignition “ON”.
3. Using multi-tester, measure voltage between pin 5(+)
and 17/18 (-).
- Specified value
- Measured value is within specified range ?11-14 Vdc
Ye s
NoPerform A2 stage
Perform A3 stage
Check connection status in TOD control unit connector.
1. Check connection status.
- Is it connected exactly?
2. In case of mal-connection, connect tightly then perform
the follows.
a. Delete fault code using Scan-100.
b. Ignition “OFF”.
c. Ignition “ON”.
d. Diagnose by Scan-100.
- Does it display fault code “1714”?Ye s
No
Ye s
No
Check short of 10A fuse (fuse No.20).
1. Detach No.20 fuse from engine room fuse box.
2. Check the existence of short.
- Is fuse normal? Yes
No
Check ground of TOD control unit.
1. Ignition “ON”.
2. Check voltage between 4/19 (+) pin and 17/18 (-)
using multi-tester (keep connection status).
- Specified value (battery is good)
- Measured value
3. Check short between 17/18 pin and body after
disconnect 30 pin connector.
- Is resistance "¥"?12Vdc (battery
voltage)
Ye s
No
Ye s
No A1
A2
A3
A4
Perform A3 stage
Perform A2 stage
Perform A3 stage
Normal system
Perform A4 stage
Replace fuse, then
perform A1 stage
Perform A4-3 stage
Replace TOD control
unit
Repair ground wiring
Ground is O.K.,
perform A5 stage

TRANSFER CASE (TOD) 5D2-25
Error in electro - magnetic clutch : fault code
“1721”, “1722”
lPhenomenon
1. Upon diagnosis by SCAN-100, it displays on fault
codes “1721,1722”.
lCause
1. Defect in electro - magnetic clutch
2. Defect in connector or wiring
- Open or short from EMC to the supply : 1721
- Short EMC to ground : 1722
Ye s
No
C1
Ye s
No Ye s
No
11-15Vdc
Ye s
No
C2
Ye s
No
Test Stage / ContentsResult
Stage Test Contents and ProcedureSpecified Value
/Yes/NoCountermeasure
Check relevant connector connection status.
1. Check relevant connector connection status with TOD
control unit.
- Does it connect correctly ?
2. Check connection status of speed sensor and clutch
coil connector (7 pin) in transfer case.
- Does it connect correctly ?
3. In case of bad connection, connect it correctly then
perform the follows :
a. Delete the memorized fault code in control unit with
Scan - 100.
b. Ignition “OFF”.
c. Ignition “ON”.
d. Diagnose by SCAN-100
- Does it display on fault codes “1721,1722” ?
Check supply voltage into electro-magnetic clutch.
1. Ignition “ON”
2. Measure voltage between pin 4/19(+) and 17/18(-) in
TOD control unit connector.
- Specified value
- Measured value is within specified range ?
3. If the specified value would not be measured, perform
the follows :
a. Check battery voltage (charging condition)
b. Check open circuit on No.13 fuse (20A)
c. Check relevant wires.
- Is the above 3a, 3b, 3c normal ?Perform C1-2 stage
Perform C1-3 stage
Perform C2 stage
Normal system Perform C2 stage
Perform C1-3 stage
Perform C3 stage
Perform C2-3 stage
Perform C3 stage
lCharging/
Replace battery
lReplace fuse
lRepair wires

TRANSFER CASE (TOD) 5D2-29
Shift motor malfunction : Fault code ® 1741,
1742, 1743
lPhenomenon
1. When change the 4H/4L switch from 4H to 4L, ‘4L’
indicator lamp turn off after blinking for a time and then
‘4WD CHECK’ indicator lamp turn on.
2. Fault codes display by diagnosis of SCAN-100 : 1741,
1742, 1743
3. The shifting operation is not occurred when 4H / 4L switch,
is operating.
lCause
Defect in shift motor, improper voltage provided, incorrect
connection in connector, short of wiring.
11-14 V
(Battery voltage)
Ye s
No E1
11-14 V
(Battery voltage)
Ye s
No
Ye s
No
E2
Ye s
No Test Stage / Contents
Result
Stage Test Contents and ProcedureSpecified Value
/Yes/NoCountermeasure
Check the input voltage of shift motor.
1. Turn the ignition switch to “ON” position.
2. Measure the Hi/Low voltage of motor which is located
between No.1/No.14 and No.2/No.15 connector of TOD
control unit with digital Multi-tester or which is located
between No.G connector and body after detaching T/C
motor connector.
- The specified value (When operates 4H/4L switch)
- Measured value is within specified range ?
3. Measure the Hi/Low voltage of motor which is located
between No.2/No.5 and No.1/No.14 connector or which
is located No.B connector and body after detaching T/C
motor connector
- The specified value (When operates 4H/4L switch)
- Measured value is within specified range ?
Check the fault condition of the relevant connector.
1. Check the installation condition of TOD control unit 30pin
connector and T/C shift motor connector.
- Is it installed properly ?
2. If the connector installation is improper, install properly
and then perform follows :
a. Delete the fault code of control unit by scan scope
b. Turn off the ignition switch
c. Turn on the ignition switch
d. Re-diagnosis of system
It displays one or more fault code among 1741 to 1743.Perform E1-3 stage
Perform E2 stage
Perform E4 stage
Perform E2 stage
Perform E3 stage
Perform E2-2 stage
Perform E3 stage
Normal system