1998 PONTIAC FIREBIRD lock

1
How to Add Coolant to the Radiator
(3800 V6 Engine)
I NOTICE:
Your engine has a specific radiator fill procedure.
Failure to follow this procedure could cause your
engine to overheat and be severely damaged.
1. You can remove the radiator pressure cap when the
cooling system, including the radiator pressure cap
and upper radiator hose, is no longer hot.
Turn the
pressure cap slowly counterclockwise until it first
stops. (Don’t press down while turning the
pressure cap.)
If you hear a hiss, wait for that to stop. A hiss means
there is still some pressure left.
5-21

How to Add Coolant to the Radiator
(VS Engine Only)
NOTICE:
The LS1 Engine (Code G) has a specific radiator
fill procedure. Failure
to follow this procedure
could cause your engine
to overheat and be
severely damaged.
1. You can remove the radiator pressure cap when the
cooling system, including the radiator pressure cap
and upper radiator hose, is
no longer hot. Turn the
pressure cap slowly
to the left (counterclockwise)
until it fist stops. (Don't press down while turning
the pressure cap.)
If you hear a hiss, wait for that to stop.
A hiss means
there is still some pressure left.
5-24

If a Tire Goes Flat Changing a Flat Tire
It’s unusual
for a tire to “blow out” while you’re driving,
especially if you maintain your tires properly. If air goes
out of a tire, it’s much more likely to leak out slowly.
But if you should ever have a “blowout,” here are a few
tips about what to expect and what to do:
If a front tire fails, the
flat tire will create a drag that
pulls the vehicle toward that side. Take your foot
off the
accelerator pedal and grip the steering wheel firmly.
Steer to maintain lane position, and then gently brake to
a stop well out of the traffic lane.
A rear blowout, particularly on a curve, acts much like a
skid and may require the same correction you’d use in a
skid. In any rear blowout, remove your foot from the
accelerator pedal. Get the vehicle under control by
steering the way you want the vehicle to
go. It may be
very bumpy and noisy, but you can still steer. Gently
brake to a stop
-- well off the road if possible.
If a tire goes flat, the next part shows how to use your
jacking equipment to change a flat tire safely. If
a tire goes flat, avoid further
tire and wheel damage
by driving slowly to a level place.
Turn on your hazard
warning flashers.
I
A CAUTION:
Changing a tire can cause an injury. The vehicle
can slip
off the jack and roll over you or other
people. You and they could be badly injured.
Find
a level place to change your tire. To help
prevent the vehicle from moving:
1. Set the parking brake firmly.
2. Put an automatic transmission shift lever in
PARK (P), or shift a manual transmission to
FIRST (1) or REVERSE (R).
3. I’urn off the engine.
To be even more certain the vehicle won’t move,
you can put blocks at the front and rear of the
tire farthest away from the one being changed.
That would be the tire on the other
side of the
vehicle, at the opposite end.
5-27

........................................................................\
......... ........................................................................\
..... ........................................................................\
.
........... ........... ....................... .......................
The following steps will tell you how to use the jack and
change a
tire.
Removing the Spare Tire and Tools
The equipment you’ll need is in the right (passenger)
rear area behind the trim panel.
First
you must remove the close-out panel. See
“Close-Out Panel” in
the Index.
On convertible models,
you must also remove the
convertible top protection panel. It’s at the upper back
of the
trunk. Turn the two screw knobs under the trunk
edge a quarter turn (left) counterclockwise to remove
the panel.
5-28

Removing the Flat Tire and Installing
the Spare Tire
Each wheel has one locknut in place of the standard
wheel nut.
A special wheel lock key (removal tool) and
instructions are located in the center console. Attach
the wheel lock key to the socket of the wheel
wrench. Remove the locking wheel
nut by turning
to the left (counterclockwise).
1. Using the wheel wrench, loosen all the wheel nuts.
Don’t remove them
yet.
5-32

3. Raise the vehicle by rotating the wheel wrench to
the right (clockwise). Raise the vehicle far enough
off the ground so there is enough room for the spare
tire
to fit. Remove all the wheel nuts and take off
the flat tire.
4. Remove any rust or dirt
from the wheel bolts,
mounting surfaces
and
spare wheel.
A CAUTION:
Rust or dirt on the wheel, or on the parts to
which
it is fastened, can make the wheel nuts
become loose after
a time. The wheel could come
off and cause an accident. When you change a
wheel, remove any rust or dirt from the places
where the wheel attaches to the vehicle.
In an
emergency, you can use a cloth or a paper towel
to do this; but be sure
to use a scraper or wire
brush later,
if you need to, to get all the rust or
dirt off.
5-35

1 A CAUTION:
Never use oil or grease on studs or nuts. If you
do, the nuts might come loose. Your wheel could
fall
off, causing a serious accident.
5. Replace the wheel nuts with the rounded end of the
nuts toward the wheel. Tighten each nut
by hand
until the wheel is held against the hub.
6. Lower the vehicle by rotating the wheel wrench to
the left (counterclockwise). Lower the jack
completely.
5-36

To remove the cap, turn it slowly to the left
(counterclockwise). The cap has a spring in it; if you let
go of the cap too soon, it will spring back to the right.
L
If you get gasoline on yourself and then
something ignites
it, you could be badly burned.
Gasoline can spray out on you
if you open the
fuel filler cap too quickly. This spray can happen
if your tank is nearly full, and is more likely in
hot weather. Open the fuel filler cap slowly and
wait for any “hiss” noise to stop. Then unscrew
the cap all the way.
Be careful not to spill gasoline. Clean gasoline from
painted surfaces
as soon as possible. See “Cleaning
the Outside of Your Vehicle” in the Index. When you put the
cap back on, turn it to the right
(clockwise) until you hear
a clicking sound. Make
sure
you fully install the cap. The diagnostic system
can determine if the fuel cap has been left
off or
improperly installed. This would allow fuel to
evaporate into the atmosphere. See “Malfunction
Indicator Lamp” in the Index.
NOTICE:
If you need a new cap, be sure to get the right
type. Your dealer can get one for you.
If you get
the wrong type, it may not fit properly. This may
cause your malfunction indicator lamp to light
and your fuel tank and emissions system may be
damaged. See “Malfunction Indicator Lamp” in
the Index.
6-7