1998 NISSAN GT-R sensor

COMBINATION METER
Combination Meter Input/Output Signal -
Specifications (~ont'd)
Signal name
Vehicle speed signal
(8 pulses)
Body
ground
Ground
I--
Oil pressure sensor
signal Measuring
condi!ion
operation.
Speedometer is in operation.
(Vehicle speed is approx.
40 km~h.)
Specification
Approx.
4.8V or OV
Vehicle speed is approx. 40
ELF0978D
-- - Approx. 2.4V
ON - Approx. OV
- I - I Refer to 'Component Parts Inspection" (EL-28).
J I I Voltage of the upper part of the wave form indicates the value checked with analogue circuit tester.
- Water Fuel gaugc
temperature gauge
1 Gauge indication with shorted
Gauge
indicaion with
3.4W test lamp connected
ELF0980D
Component Parts inspection
SPEEDOMETER, TACHOMETER, FUEL GAUGE AND
WATER TEMPERATURE
GAUGE
Remove each meter from the meter control unit and check the
resistance between the terminals as shown below.
Checkina terminal I
Speedometer and I Fuel gauge and water I Resistance R
B-D I B-C I Approx. 230 - 310
tachometer
A-C
OIL PRESSURE GAUGE
Disconnect oil pressure sensor connector.
Turn the ignition switch ON, and connect test lamp and lead
wire with the meter attaching screw as shown left. Check the
gauge indication.
temperature gauge
A-C
ADD~OX.
190 - 260

COMBINATION METER
Component Parts Inspection (Cont'd)
If the measured resistance is out of the specification with the
thermal transmitter on vehicle, remove the thermal transmitter
from the vehicle and measure resistance as
shown left.
Water temperature "C 1 Resistance R
Approx. 60 I Approx. i70 - 21 0
Approx. 65 I Approx. 140 - 170
Approx. 80 I Approx. 76 - 90
I
- - -- Appro~. 100 Approx. 47 - 53
OIL PRESSURE SENSOR (OIL PRESSURE WARNING
LAMP SWITCH)
Check continuity between oil pressure sensor and body ground.
Terminal No.
OIL PRESSURE SENSOR
Engine is stopped.
Engine is started.
Check the resistance between the oil pressure sensor and body
ground.
Condition
Terminal No.
I Oil pressure MPa (kgkmq-1 Resistance R
Oil pressure
MPa (kg/cm2) 1 Continuity
Less than
0.01 - 0.024
(0.1 - 0.25)
More than 0.01 - 0.024
(0.1 - 0.25)
0.2 (2.0) Approx. 37 - 45
Yes
No

TRIPLE METER
Special Service Tool
Tool number
Tool name Description
i
€GI 51 3 0000 Boost sensor
check
Handy vacuum pump
Component Parts Location
Triple meter
I
Circuit Diagram
Behind triple meter
h
To lighting SW or tail lamp relay
Boost sensor
Oil temperature sensor
* BOOS^ sensor

TRIPLE METER
Triple Meter InputlOutput Signal Specifications
Component
Parts Inspection
Terminal No.
1
4
9
10
14
17
BOOST SENSOR
Connect handy vacuum pump (special service tool) to boost
sensor.
Apply battery voltage (12V) to terminal No. 1 and connect ter-
minal No.
3 to the ground. Then, measure voltage between
terminal No.
2 and the ground.
I I - I Refer to "Component Parts Inspectionn.
Signal
name
Boost sensor signal
Illumination
power
supply
illumination ground
Ground ignition power supply
Oil temperature sensor signal
Pressure
kPa (mmHg) I Voltage V
I
- pp Atmospheric pressure Approx. 2.2
-47 (-350) 1 Approx. 1.4
-
Specification
Approx. 2.2V
Approx. 12V
Approx. OV
Approx.
OV
Approx. 12V
Measuring condition
OIL TEMPERATURE SENSOR
lgnition
switch
ON
OFF
ON
ON
ON
Remove oil temperature sensor from the vehicle and measure
resistance as shown
left.
Operation or condition
0 mmHg
Lighting switch: 1
ST
-
-
-
Oil temperature "C
Approx. 70
-- - - --
Resistance R
Approx. 92.0
Approx. 90
Approx.
110
Approx. 130 - -- Appro~. 48.5
Approx. 27.3
Approx. 16.3
Approx. 150
Approx. 10.2
CAUTION:
Always use new engine
oil.

ENGINE MECHANICAL [ RB20DE (UB) 1
TIGHTENING TORQUE
Unit: N.m (kg-m)
Engine cover
Throttle body
Throttle position sensor
IAA unit (ACC valve)
lntake manifold collector
(upper)
Intake manifold collector
Intake manifold
Vacuum tank
Engine coolant temperature
sensor
- --
' Fuel tube
Pressure regulator
Fuel damper
Fuel hose clamp bolt
(in engine compartment)
Exhaust manifold cover
' Exhaust manifold
Oxygen sensor
Crank pulley
Cam pulley (INT)
Cam pulley
(EXH)
Timing belt cover
Timing belt rear cover
Tensioner pulley
Idler pulley
Crankshaft position sensor
' Oil pan
Oil strainer
Oil pan drain plug
ignition coil
Spark plug
* Rocker cover
Camshaft bracket
Camshaft baffle plate 5.1
- 6.5 (0.52 - 0.66)
20
- 29 (2.0 - 3.0)
1) 5.5 - 7.5 (0.56 - 0.76)
?) 5.5 - 7.5 (0.56 - 0.76)
:Tighten separately in twice.)
Cylinder head bolt
Cylinder head sub bolt
VTC solenoid
' Main bearing cap
Connecting rod nut
Flywheel and drive plate
Engine coolant drain plug
Knock sensor
Radiator mounting bracket
Auxiliary electric fan
Water pump (M6 bolt)
(M8 bolt)
(MI 0 bolt)
Water inlet
Oil pump assembly
Accelerator cable
lock nut
Fuel tank strap
Fuel sender unit lock
ring
Exhaust manifold to front
tube Front tube to catalytic
converter Catalytic converter to cent
tube Center tube to main
muffler
Alternator (main)
(stay side)
Starter motor Unit:
N-m (kg-m)
1)
29 (3.0)
2) 98 (10.0)
3)
0
(0)
4) 25
- 34 (2.5 - 3.5) GI
5) 95" - 100"
(Angle tightening)
Ec
9.0 - 12 (0.92 - 1.2)
25
- 34 (2.5 - 3.5)
49
- 59 (5.0 - 6.0) h$7'
1) 14 - 16 (1.4 - 1.6)
2) 45"
- 50"
(Angle tightening)
BW
93 - 103 (9.5 - 10.5)
34 - 44 (3.5 - 4.5)
25
- 34 (2.5 - 3.5) ST
': Tighten as specified tightening order.
1): Tighten separately in several times.

ENGINE MECHANICAL
TIGHTENING TORQUE
Engine cover
' Throttle body
Throttle position sensor
IAA unit (ACC valve)
' Intake manifold collector
(upper)
' Intake manifold collector
Intake manifold
Vacuum tank
Engine coolant temperature
sensor
' Fuel tube
Pressure regulator
Fuel damper
Fuel hose clamp bolt
(in engine compartment)
Exhaust manifold cover
Exhaust manifold
Oxygen sensor
Crank pulley
Cam pulley (INT)
Cam pulley
(EXH)
Timing belt cover
Ttming belt rear cover
Tensioner pulley
Idler pulley
Crankshaft position sensor
' Oil pan
Oil strainer
Oil pan drain plug
Ignition coil
Spark plug
Rocker cover
* Camshaft bracket
Camshaft baffle plate Unit:
Nm (kg-m)
5.0
- 6.5 (0.51 - 0.66)
1) 8.8
- 11 (0.9 - 1.1)
2) 18
- 22 (1.8 - 2.2)
2.0
- 2.4 (0.20 - 0.24)
8.4
- 11 (0.86 - 1 .I)
18
- 22 (1.8 - 2.2)
5.1
- 6.5 (0.52 - 0.66)
20
- 29 (2.0 - 3.0)
1) 5.5 - 7.5 (0.56 - 0.76)
2) 5.5 - 7.5 (0.56 - 0.76)
:Tighten separately in twice.)
Cylinder head bolt
Cylinder head sub bolt
VTC solenoid
Main bearing cap
Connecting rod nut
Flywheel and drive plate
Engine coolant drain plug
Knock sensor
Radiator mounting bracket
Auxiliary electric fan
Water pump
(M6 bolt)
(M8 bolt)
(M 1 0 bolt)
Water inlet
Oil pump assembly
-
Accelerator cable lock nut
Fuel tank strap
Fuel sender unit lock
ring
Exhaust manifold to front
tube
Front tube to catalytic
converter
Catalytic converter to center
tube Center tube to main
muffler
Alternator (main)
(stay side)
Starter motor Unit:
N.m (kg-m)
1) 29 (3.0)
2) 98 (10.0) 3) 0 (0)
@
4)
25 - 34 (2.5 - 3.5)
5) 95" - 100"
(Angle tightening)
E
9.0 - 12 (0.92 - 1.2)
25
- 34 (2.5 - 3.5) j$? 49 - 59 (5.0 - 6.0)
1) 14- 16
(1.4- 1.6)
2) 60"
- 65" BR
(Angle tightening)
93
- 103 (9.5 - 10.5)
34 - 44 (3.5 - 4.5)
25
- 34 (2.5 - 3.5) a=
': Tighten as specified tightening order.
1): Tighten separately in several times.

ENGINE MECHANICAL pEZBq
TIGHTENING TORQUE
Engine cover
' Throttle body
Throttle position sensor
IAA unit
(ACC valve)
' Intake manifold collector
* Intake manifold
Engine coolant temperature
sensor
' Fuel tube
Pressure regulator
Fuel damper
Fuel hose clamp bolt
(in engine compartment)
Turbocharger Oil tube
Water tube (block side)
(turbocharger side)
Oxygen sensor
Exhaust manifold cover
' Exhaust manifold
Crank pulley
Cam pulley (INT)
Cam pulley
(EXH)
Timing belt cover
Timing belt rear cover
Tensioner pulley
Idler pulley
Crankshaft position sensor
' Oil pan
Oil strainer
Oil pan drain plug
Ignition coil
Spark plug
' Rocker cover
' Camshaft bracket
Camshaft baffle plate Unit:
N.m (kg-m)
5.0
- 6.5 (0.51 - 0.66)
1)
8.8
- 11 (0.9 - 1.1)
2)
18
- 22 (1 -8 - 2.2)
2.0
- 2.4 (0.20 - 0.24)
8.4
- 11 (0.86 - 1.1)
18
- 22 (1.8 - 2.2)
18
- 22 (1 -8 - 2.2)
20
- 29 (2.0 - 3.0)
5.1
- 6.5 (0.52 - 0.66)
20
- 29 (2.0 - 3.0)
1) 5.5
- 7.5 (0.56 - 0.76)
2) 5.5 - 7.5 (0.56 - 0.76)
(Tighten separately in twice.)
' Cylinder head boit
Cylinder head sub bolt
VTC solenoid
" Main bearing cap
Connecting rod
nut
Oil jet
Flywheel and drive plate
Engine coolant drain plug
Knock sensor
Radiator mounting bracket
Auxiliary electric fan
Water pump (M6 bolt)
(M8 bolt)
(MI
0 bolt)
Water inlet
Oil pump assembly
Accelerator cable lock nut
Fuel tank strap
Fuel sender unit lock
ring
Exhaust manifold to front
tube
Front tube to catalytic
converter
Catalytic converter to center
tube
Center tube to main
muffler
Alternator (main)
(stay side)
Starter motor Unit:
N.m (kg-m)
1) 29 (3.0)
2) 98 (10.0)
3) 0 (0)
4) 25 - 34 (2.5 - 3.5)
5) 95"
- 100"
(Angle tightening)
I%
9.0 - 12 (0.92 - 1.2)
25
- 34 (2.5 - 3.5)
49
- 59 (5.0 - 6.0) AT
1) 14 - 16 (1.4 - 1.6)
2) 60" - 65"
(Angle tightening) BR
30 - 40 (3.1 - 4.1)
93
- 103 (9.5 - 10.5)
34 - 44 (3.5 - 4.5) ST
25 - 34 (2.5 - 3.5)
3.8
- 4.5 (0.39 - 0.46) I%$
5.1 - 6.5 (0.52 - 0.66)
17
- 21 (1.7 - 2.1)
20
- 23 (2.0 - 2.3) kIA
35 - 47 (3.6 - 4.8)
16
- 21 (1.6 - 2.1)
9.0
- 12 (0.92 - 1.2) a=
': Tighten as specified tightening order.
1): Tighten separately in several times.