1998 MITSUBISHI MONTERO check
[x] Cancel search: checkPage 20 of 1501
instrument panel.
(
2) - See Figs. 1 and 2.
(
3) - Engine ID is eighth character of VIN.
(
4) - Fuel system is a Sequential Fuel Injection (SFI) system.
(
5) - Ignition timing is computer-controlled.
(
6) - This system may also be referred to as distributor ignition.
(
7) - This system may also be referred to as distributorless
ignition.
\
\
\
\
\
\
\
\f
VIN DEFINITION
J A 3 A Y 3 6 A 1 W U 0 0 0 0 0 1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
1 - Indicates Nation of Origin.
2 - Indicates Manufacturer.
3 - Indicates Vehicle Type.
4 - Indicates Restraint System. ( 1)
5 - Indicates Model.
6 - Indicates Vehicle Series.
7 - Indicates Body Type.
8 - Indicates Engine Type and Make.
9 - Indicates Check Digit.
10 - Indicates Model Year.
11 - Indicates Assembly Plant.
12-17 - Indicates Serial Number.
( 1) - On Montero & Montero Sport, fourth character of VIN indicates
GVWR.
VIN CODE/YEAR APPLICATIONS
VIN CODE/YEAR APPLICATION TABLE\
\
\
\
\
\
VIN Code Model Year
T ................................................... 1996
V ................................................... 1997
W ................................................... 1998
\
\
\
\
\
\
ENGINE CODE LOCATIONS
Fig. 1: Engine Code Locations (Diamante)
Courtesy of Chrysler Corp.
Page 27 of 1501
CO Carbon Monoxide
CO2 Carbon Dioxide
CONV Convertible
CP Canister Purge
CPA Connector Position Assurance
CPS Crank Position Sensor
CTS Coolant Temperature Sensor
CV Check Valve or Constant Velocity
CVC Constant Vacuum Control
CW Clockwise
CYL or Cyl. Cylinder
Calif. California
Carb. Carburetor
Chrg. Charging
Circ. Circuit
Cntrl. Control
Comp. Compressor or Compartment
Conn. Connector
Cont. Continued
Conv. Convertible or Converter
Cu. In. Cubic Inch
Cyl. Cylinder
\
\
\
\
\
\
\
\f
"D" ABBREVIATION TABLE
"D" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
"D" Drive
DBC Dual Bed Catalyst
DC Direct Current or Discharge
DDD Dual Diaphragm Distributor
DERM Diagnostic Energy Reserve Module
DFI Digital Fuel Injection
DIC Driver Information Center
DIS Direct Ignition System
DIS Distributorless Ignition System
DIST Distribution
DISTR Distributor
DK BLU Dark Blue
DK GRN Dark Green
DME Digital Motor Electronics (Motronic System)
DOHC Double Overhead Cam
DOT Department of Transportation
DP Dashpot
DRB-II Diagnostic Readout Box
DVOM Digital Volt/Ohm Meter (see VOM)
Def. Defogger or Defroster
Def. Defrost
Defog. Defogger
Diag. Diagnostic
Dist. Distributor or Distribution
Dr. Door
\
\
\
\
\
\
\
\f
"E" ABBREVIATION TABLE
"E" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
Page 31 of 1501
mm Millimeters
M/T Manual Transaxle or Transmission
MA PFI Mass Air Sequential Port Fuel Injection system
MA or MAF Mass Airflow
MAF Mass Air Flow sensor
MAFS Mass Airflow Sensor
MAP Manifold Absolute Pressure sensor
MAT Manifold Air Temperature
MCU Microprocessor Control Unit
MCV Mixture Control Valve
MEM-CAL Memory Calibration Chip
MFI Multiport Fuel Injection
MIL Malfunction Indicator Light
MLP Manual Lever Position
MPFI Multi Point Fuel Injection
MPH Miles Per Hour
MPI Multi-Point (Fuel) Injection
Man. Manual
Mech. Mechanical
Mem. Memory
Mtr. Motor
\
\
\
\
\
\
\
\f
"N" ABBREVIATION TABLE
"N" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
N.m Newton-Meter
NA Not Available
NDS Neutral Drive Switch
NGS Neutral Gear Switch
NOx Oxides of Nitrogen
NPS Neutral Pressure Switch
No. Number
Nos. Numbers
\
\
\
\
\
\
\
\f
"O" ABBREVIATION TABLE
"O" ABBREVIATION TABLE \
\
\
\
\
\
\
ABBREVIATION DEFINITION
\
\b\
\
\
\
\
\
O Oxygen
O.D. Outside Diameter
O/S Oversize
O2 Oxygen
OC Oxidation Catalyst
OCC Output Circuit Check
OD Overdrive
ODO Odometer
OHC Overhead Camshaft
ORG Orange
OSC Output State Check
Opt. Option or Optional
oz. Ounce
ozs. Ounces
\
\
\
\
\
\
\
\f
Page 36 of 1501
A/C COMPRESSOR REFRIGERANT OIL CHECKING
1998 Mitsubishi Montero
1998 A/C SYSTEM GENERAL SERVICING
Mitsubishi - Compressor Refrigerant Oil Checking
Diamante, Eclipse, Galant, Mirage, Montero, Montero Sport &
3000GT
* PLEASE READ THIS FIRST *
NOTE: Always refer to underhood A/C specification label in engine
compartment or A/C compressor label while servicing A/C
system. If engine compartment/compressor label specifications
differ from specifications in this article, use
underhood/compressor label specifications.
A/C COMPRESSOR APPLICATIONS
A/C COMPRESSOR APPLICATION TABLE \
\
\
\
\
\
Application Compressor
Diamante ......................... Sanden MSC105CVS Scroll
Eclipse
2.0L Non-Turbo ............. Nippondenso 10PA17C 10-Cyl.
2.0L Turbo & 2.4L .............. Sanden MSC105CVS Scroll
Galant ............................ Sanden MSC90C12 Scroll
Mirage ............................... Sanden MSC90 Scroll
Montero ....................... Nippondenso 10PA15 10-Cyl.
Montero Sport ...................... Sanden MSC105C Scroll
3000GT .............................. Sanden MSC105 Scroll
\
\
\
\
\
\
REFRIGERANT OIL & REFRIGERANT CAPACITY SPECIFICATIONS
NOTE: DO NOT exceed A/C system refrigerant oil capacity when
servicing system.
REFRIGERANT OIL & R-134a REFRIGERANT CAPACITY TABLE
\
\
\
\
\
\
Application ( 1) Oil Refrigerant
Ounces Ounces
Diamante .................... 5.7-6.4 ........ 22.9-24.3
Eclipse
2.0L Non-Turbo ............ 2.7-4.1 ........ 24.7-26.1
2.0L Turbo & 2.4L ......... 5.7-6.4 ........ 24.7-26.1
Galant ...................... 4.1-5.1 ........ 22.9-24.3
Mirage ...................... 4.1-5.1 ........ 19.6-21.0
Montero ..................... ( 2) 4.1 ........ 21.2-22.9
Montero Sport ............... ( 2) 5.7 ........ 22.9-24.0
3000GT ...................... 4.7-6.1 ........ 26.1-27.9
( 1) - Total system capacity, unless otherwise noted.
( 2) - Compressor refrigerant oil capacity.
\
\
\
\
\
\
REFRIGERANT OIL
Page 37 of 1501
Only NEW, moisture-free refrigerant oil should be used in the
air conditioning system. This oil is highly refined and dehydrated so
moisture content is less than 10 parts per million. The oil container
must be tightly closed at all times when not in use, or moisture from
the air will be absorbed into the refrigerant oil.
SERVICING PRECAUTIONS
DISCHARGING SYSTEM
Discharge A/C system, using approved refrigerant
recovery/recycling equipment that meets SAE J2210 requirements. Always
follow recovery/recycling equipment manufacturer's instructions. After
refrigerant recovery process is completed, replace any refrigerant oil
removed with the same amount of NEW refrigerant oil.
DISCONNECTING LINES & FITTINGS
After system is discharged, carefully clean area around all
fittings to be opened. Always use 2 wrenches when tightening or
loosening fittings. Some refrigerant lines are connected with a
coupling. Special tools may be required to disconnect lines. Cap or
plug all openings as soon as lines are removed. DO NOT remove shipping
caps from replacement components until ready to install.
CONNECTING LINES & FITTINGS
NOTE: Ensure all replacement component connections match
connections of system being worked on.
Always use a NEW gasket or "O" ring when connecting lines or
fittings. Coat "O" ring with NEW refrigerant oil and ensure it is not
twisted during installation. Always use two wrenches to prevent damage
to lines and fittings.
PLACING SYSTEM IN OPERATION
After component service or replacement has been completed and
all connections have been made, thoroughly evacuate system with a
vacuum pump. Charge system with proper amount of refrigerant and
perform leak test. See REFRIGERANT OIL & REFRIGERANT SPECIFICATIONS
table for system capacities. Ensure there are no leaks at any fitting
that has been opened. After system has been leak tested, check system
performance.
NIPPONDENSO 10-CYL.
Eclipse 2.0L Non-Turbo & Montero
Replacement compressor is shipped with NEW refrigerant oil.
Drain, measure and discard refrigerant oil from old compressor. Drain
NEW refrigerant oil from replacement compressor equal to difference
between amount drained from old compressor and amount shipped in
replacement compressor. If any other components are replaced, add NEW
refrigerant oil as specified. See COMPONENT REFRIGERANT OIL CAPACITIES
(MITSUBISHI - NIPPONDENSO 10-CYL.) table.
COMPONENT REFRIGERANT OIL CAPACITIES TABLE (NIPPONDENSO)
\
\
\
\
\
\
Component Ounces
Compressor ( 1)
Page 39 of 1501
A/C COMPRESSOR SERVICING
1998 Mitsubishi Montero
1998 GENERAL SERVICING
Mitsubishi - Compressor Servicing
Diamante, Eclipse, Galant, Mirage, Montero, Montero Sport &
3000GT
A/C COMPRESSOR APPLICATIONS
A/C COMPRESSOR APPLICATION TABLE \
\
\
\
\
\
Application Compressor
Diamante ......................... Sanden MSC105CVS Scroll
Eclipse
2.0L Non-Turbo ............. Nippondenso 10PA17C 10-Cyl.
2.0L Turbo & 2.4L .............. Sanden MSC105CVS Scroll
Galant ............................ Sanden MSC90C12 Scroll
Mirage ............................... Sanden MSC90 Scroll
Montero ....................... Nippondenso 10PA15 10-Cyl.
Montero Sport ...................... Sanden MSC105C Scroll
3000GT .............................. Sanden MSC105 Scroll
\
\
\
\
\
\
NOTE: Due to variety of clutch and shaft seal configurations,
obtain appropriate A/C compressor service tools for
compressor being serviced. Land Rover and Jaguar compressor
service information not available at time of publication.
NIPPONDENSO
CLUTCH COIL
Removal
1) Hold clutch plate stationary. Remove clutch plate center
bolt and clutch plate. If clutch plate cannot be removed by hand,
tighten an 8-mm or 10-mm bolt into clutch plate center bolt hole to
remove clutch plate.
2) Remove shim(s) and pulley snap ring from compressor shaft\
.
Tap pulley using a plastic hammer and remove pulley from compressor
shaft. See Fig. 1 or 2. Remove retaining screw for clutch coil lead.
Remove clutch coil snap ring and clutch coil.
Installation
1) To install, reverse removal procedure. Ensure clutch coil
pin is aligned with hole in compressor housing. Ensure clutch coil
lead is positioned properly. Ensure NEW snap rings are installed with
beveled side facing out. Tighten shaft bolt to 10-13 ft. lbs. (14-17
N.m).
2) Check air gap between clutch plate and pulley. Position
dial indicator on clutch plate. Energize clutch coil and zero dial
indicator. De-energize clutch coil and measure air gap (clutch plate
movement). Ensure air gap between clutch plate and pulley is 0.014-0.
026" (0.35-0.65 mm). If air gap is incorrect, add or remove shim(s) \
as
necessary. Ensure pulley rotates freely.
NOTE: On some compressors, it is necessary to use a dial indicator
on clutch plate to check air gap. Energize clutch coil and
zero dial indicator. De-energize clutch coil and measure air
gap. Ensure air gap is as specified.
Page 54 of 1501
affecting performance .. 2 ........... (1) Suggest repair or
replacement.
Connector missing ....... C ............ Require replacement.
Current draw out of
specification .......... B .. Require repair or replacement.
Inoperative ............. A ........ ( 2) Require replacement.
Missing ................. C ............ Require replacement.
Motor speed
insufficient ........... 2 .. Suggest repair or replacement.
Noisy ................... 2 ............ Suggest replacement.
Rotation incorrect for
application ............ B .. Require repair or replacement.
Terminal broken ......... A .. Require repair or replacement.
Terminal burned, affecting
performance ............ A ........... ( 1) Require repair or
replacement.
Terminal burned, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal corroded,
affecting performance .. A .. Require repair or replacement.
Terminal corroded, not
affecting performance .. 2 .. Suggest repair or replacement.
Terminal loose, affecting
performance ............ B .. Require repair or replacement.
Terminal loose, not
affecting performance .. 1 .. Suggest repair or replacement.
Vibration ............... 1 ............ Suggest replacement.
Wire lead conductors
exposed ................ B .. Require repair or replacement.
Wire lead corroded ...... A .. Require repair or replacement.
Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
( 1) - Determine cause and correct prior to repair or
replacement of part.
( 2) - Check fan motor/controls. Inoperative includes
intermittent operation or out of OEM specification.
\
\
\
\
\
\
\
BLOWER RESISTORS
BLOWER RESISTOR INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.
Conductor exposed ....... A ............ Require replacement.
Connector broken ........ A .. Require repair or replacement.
Connector melted,
affecting performance .. A ........... ( 1) Require repair or
replacement.
Connector melted, not
affecting performance .. 1 ........... ( 1) Suggest repair or
replacement.
Page 63 of 1501
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ............ Require replacement.
Wire lead conductors
exposed ................ B .. Require repair or replacement.
Wire lead corroded ...... A .. Require repair or replacement.
Wire lead open .......... A .. Require repair or replacement.
Wire lead shorted ....... A .. Require repair or replacement.
(1) - Refer to manufacturer's diagnostic trouble code
procedure and require repair or replacement of
affected component(s).
( 2) - Determine cause and correct prior to repair or
replacement of part.
( 3) - Determine source of contamination, such as engine coolant,
fuel, metal particles, or water. Require repair or
replacement. Check for accepted cleaning procedure.
( 4) - Inoperative includes intermittent operation or out of
OEM specification. Some components may be serviceable.
\
\
\
\
\
\
\
COOLANT
COOLANT INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Acidity (pH) incorrect .. 1 ........... Suggest correction or
replacement.
Contaminated ............ B ...... ( 1) Require replacement or
recycling. Further
inspection required.
Level incorrect ......... B .......... ( 2) Require filling to
proper level.
Maintenance intervals ... 3 ........ ( 3) Suggest replacement.
Mixture incorrect ....... B ........... Require correction or
replacement.
Type incorrect .......... B ............ Require replacement.
( 1) - Determine source of contamination and require correction
prior to coolant replacement.
( 2) - Determine source of incorrect level and suggest repair.
( 3) - The system should be drained and/or flushed and
refilled with correct coolant according to OEM
recommended service interval and procedures.
\
\
\
\
\
\
\
COOLING FAN BLADES
COOLING FAN BLADE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Application incorrect ... B ............ Require replacement.
Attaching hardware
broken ................. A ... Require repair or replacement
of hardware.
Attaching hardware
missing ................ C .......... Require replacement of
hardware.
Attaching hardware not
functioning ............ A ... Require repair or replacement
of hardware.