1998 MITSUBISHI MONTERO low oil pressure

[x] Cancel search: low oil pressure

dashboard radio controls service schedule engine oil capacity technical data jacking points

Load previous 8 pages

Page 1163 of 1501

MITSUBISHI MONTERO 1998 Service Manual 2) Remove cam ring, vanes, shaft assembly and "O" rings.
Remove snap ring from shaft assembly. Remove collar, rotor and side
plate from shaft.
3) Pry oil seal out of housing. Remove

Page 1164 of 1501

MITSUBISHI MONTERO 1998 Service Manual damage. Inspect groove of rotor vane and cam surface for stepped wear.
Check vane for damage. Install vane into rotor groove. Measure
clearance between vane and rotor groove. If clearance exceeds .002

damage. Inspect groove of rotor vane and cam surface for stepped wear.
Check vane for damage. Install vane into rotor groove. Measure
clearance between vane and rotor groove. If clearance exceeds .0024"
(.061 mm), replace entire assembly.
2) Check ring and rotor sides for damage. Replace entire
assembly if any damage is present. Check sliding surfaces of control
valve for obstructions. Replace parts as required. If control valve is
replaced, always use valve with same identification mark as one being
replaced. Check power steering fluid pressure.
Reassembly
1) Lubricate "O" rings and internal pump components with ATF
before reassembly. Install flow control valve spring and control valve
in housing.
2) Install and tighten pressure connector. Depress control
valve to check for smooth operation. Apply grease to lip of oil seal.
Install oil seal into pump body. Install pulley assembly into pump
body.
3) Install rotor to pulley assembly with punch mark at pump
cover side. Install snap ring. Lift rotor to ensure that snap ring is
in countersunk part of shaft. Align cam ring dowel holes and install
cam ring with punch mark on pump body side.
4) Apply transmission fluid to vanes, and install vanes onto
rotor with rounded edges outward. Install "O" ring, cam case and pump
cover. Install and tighten suction connector.
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS\
\
\
\
\
\
\

Application Ft. Lbs. (N.m)\
Adjusting Bolt Lock Nut .................................... 27 (37)\
Idler Arm Bracket-To-Frame Bolt & Nut
Montero ............................................ 40-47 (54-64)\
Montero Sport ............................................ 43 (59)\
Idler Arm-To-Bracket Lock Nut ............................. 101 (44)\
Oil Pump Cover Bolts ....................................... 15 (20)\
Pitman Arm-To-Cross Shaft Nut
Montero ........................................ 108-123 (146-176)\
Montero Sport .................................. 108-123 (147-167)\
Pressure Hose In-Line Fitting
Montero .................................................. 25 (34)\
Montero Sport ............................................ 16 (22)\
Relay Rod-To-Idler Arm Nut ................................. 33 (44)\
Relay Rod-To-Pitman Arm Nut ................................ 33 (44)\
Side Cover Bolts
Montero .................................................. 36 (49)\
Montero Sport ...................................... 41-47 (50-64)\
Steering Gear Hose Fittings ................................ 11 (15)\
Steering Gear-To-Frame Bolts ......................... 40-47 (54-64)\
Tie Rod Adjusting Sleeve Lock Nuts ......................... 69 (93)\
Tie Rod End Castle Nuts .................................... 33 (44)\
Valve Housing Bolts
Montero .................................................. 36 (49)\
Montero Sport ...................................... 41-47 (56-64)\
Valve Housing Lock Nut ......................................... ( 1)
( 1) - Tighten lock nut until it contacts bearing race.
\
\
\
\
\
\
\

Page 1189 of 1501

MITSUBISHI MONTERO 1998 Service Manual Stud loose in
taper hole ............. A ........... (7) Require repair or
replacement.
Taper hole elongated .... A ........ ( 8) Require

Stud loose in
taper hole ............. A ........... (7) Require repair or
replacement.
Taper hole elongated .... A ........ ( 8) Require replacement.
Threads damaged ......... A .. Require repair or replacement.
Threads stripped (threads
missing) ............... A ........ ( 7) Require replacement.
Wear exceeds
manufacturer's
specifications .......... B ............ Require replacement.
( 1) - If greaseable, grease joint. If problem persists or
joint is non-greaseable, require replacement.
( 2) - Cracked grease boot will allow contaminants to enter
the joint and will accelerate wear.
( 3) - Lack of grease boot will allow contaminants to enter
the joint and will accelerate wear.
( 4) - Torn grease boot will allow contaminants to enter the
joint and will accelerate wear.
( 5) - If manufacturer's procedures for inspection exist, use
those procedures; otherwise, use an approved inspection
method such as the dry park check.
CAUTION: DO NOT use pliers or pry bar to check ball and
socket movement. Use only moderate hand pressure.
( 6) - Excessive looseness is defined as being significant
enough to affect vehicle handling or structural
integrity.
( 7) - Check for damaged taper hole.
( 8) - Check for damaged stud.
\
\
\
\
\
\
\

SHOCK ABSORBERS, STRUT CARTRIDGES AND STRUT ASSEMBLIES
You are not required to replace shocks or struts in axle
sets. However, when replacing a shock or strut due to the conditions
that follow, you may suggest replacement of the other shock or strut
on the same axle for improved performance and preventive maintenance.
* Part is close to the end of its useful life
* To extend tire life
* To balance ride and handling
* To improve stopping distance
When replacing steering and/or suspension components which
may affect an alignment angle, you are required to check and adjust
alignment as needed. Refer to the OEM specifications.
Under no circumstances should a technician bend struts or
strut housings.
A vehicle's load-carrying and handling abilities are limited
by its suspension, tires, brakes, and driveline. Installing coil over
shocks or any other load assist device does not increase the vehicle's
load capacity. See the vehicle owner's manual for more details.
NOTE: If vehicle is equipped with original equipment coil over
shocks, apply the conditions for coil springs from the
SPRINGS - COIL, LEAF AND TORSION BAR section of the
STEERING AND SUSPENSION guidelines. If the vehicle is
equipped with add-on coil over shocks, you may suggest
replacing the shocks with standard shocks for any spring-
related condition.
SHOCK ABSORBER, STRUT CARTRIDGE AND STRUT ASSEMBLY INSPECTION
\
\
\
\
\
\
\

Page 1270 of 1501

Page 1359 of 1501

MITSUBISHI MONTERO 1998 Service Manual removed to drain fluid. Remove oil filter/screen if necessary.
2) If oil filter/screen is replaced, tighten bolts to
specification. See TORQUE SPECIFICATIONS . Clean oil pan, replace
gasket,

Page 1374 of 1501

$MITSUBISHI MONTERO 1998 Service Manual Fires With Key Flywheel runout contributes released. Engine to the intermittent nature Fires and Cranks Normally ��\ ��\ ��\ ��\$

Fires With Key Flywheel runout contributes
released. Engine to the intermittent nature
Fires and Cranks
Normally
\
\
\
\
\
\
\

AIR CONDITIONING & HEAT
AIR CONDITIONING TROUBLE SHOOTING
WARNING: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
BASIC AIR CONDITIONING TROUBLE SHOOTING CHART
\
\
\
\
\
\
\

CONDITION POSSIBLE CAUSE\
\
\
\
\
\
\

Compressor Not Working
Compressor clutch circuit open.

Compressor clutch coil inoperative.

Poor clutch ground connection.

Fan belts loose.

Thermostatic switch inoperative.

Thermostatic switch not adjusted.

Ambient temperature switch open.

Superheat fuse blown.\
\
\
\
\
\
\

Excessive Noise or Vibration
Missing or loose mounting bolts.

Bad idler pulley bearings.

Fan belts not tightened correctly.

Compressor clutch contacting body.

Excessive system pressure.

Compressor oil level low.

Damaged clutch bearings.

Damaged reed valves.

Damaged compressor.\
\
\
\
\
\
\

Insufficient or No Cooling;
Compressor Working
Expansion valve inoperative.

Heater control valve stuck open.

Low system pressure.

Blocked condenser fins.

Blocked evaporator fins.

Vacuum system leak.

Vacuum motors inoperative.

Control cables improperly adjusted.

Restricted air inlet.

Mode doors binding.

Blower motor inoperative.

Temperature above system capacity.\
\
\
\
\
\
\

HEATER SYSTEM TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to

Page 1382 of 1501

MITSUBISHI MONTERO 1998 Service Manual Excessive Oil Worn valve stems or guides Replace stems or
Consumption guides, See ENGINES
Valve "O" ring seals Replace "O" ring seal

Excessive Oil Worn valve stems or guides Replace stems or
Consumption guides, See ENGINES
Valve "O" ring seals Replace "O" ring seals,
damaged See ENGINES
Plugged oil drain back holes Remove restrictions
Improper PCV valve Replace PCV valve
operation
Engine oil level too high Remove excess oil
Engine oil too thin Replace thicker oil
Valve stem oil deflectors Replace oil deflectors
damaged
Incorrect piston rings Replace piston rings,
See ENGINES
Piston ring gaps not Reinstall piston rings,
staggered See ENGINES
Insufficient piston ring Replace rings, See
tension ENGINES
Piston ring grooves or oil Replace piston rings,
return slots clogged See ENGINES
Piston rings sticking in Replace piston rings,
grooves See ENGINES
Piston ring grooves Replace piston and
excessively worn rings, See ENGINES
Compression rings installed Replace compression
upside down rings correctly, See
ENGINES
Worn or scored cylinder Rebore cylinders or
walls replace block
Mismatched oil ring Replace oil ring
expander and rail expander and rail, See
ENGINES
Intake gasket dowels too Replace intake gasket
long dowels
Excessive main or connecting Replace main or
rod bearing clearance connecting rod
bearings, See ENGINES
\
\
\
\
\
\
\

No Oil Pressure Low oil level Add oil to proper level
Oil pressure sender or Replace sender or gauge
gauge broken
Oil pump malfunction Remove and overhaul oil
pump, See ENGINES
Oil pressure relief valve Remove and reinstall
sticking valve
Oil pump passages blocked Overhaul oil pump, See
ENGINES
Oil pickup screen or tube remove restriction
blocked
Loose oil inlet tube Tighten oil inlet tube
Loose camshaft bearings Replace camshaft
bearings, See ENGINES
Internal leakage at oil Replace block or
passages cylinder head
\
\
\
\
\
\
\

Low Oil Pressure Low engine oil level Add oil to proper level
Engine oil too thin Remove and replace with
thicker oil
Excessive oil pump Reduce oil pump
clearance clearance, See ENGINES
Oil pickup tube or screen Remove restrictions
blocked
Main, rod or cam bearing Replace bearing to
clearance excessive reduce clearance, See

Page 1390 of 1501

$MITSUBISHI MONTERO 1998 Service Manual Incorrect injector pump Check pressure, see housing pressure FUEL SYSTEMS ��\ ��\ ��\ ��$

Incorrect injector pump Check pressure, see
housing pressure FUEL SYSTEMS
\
\
\
\
\
\
\

Engine Cooling system leaks Check cooling system
Overheating and repair leaks
Belt slipping or damaged Check tension and/or
replace belt
Thermostat stuck closed Remove and replace
thermostat, see
ENGINE COOLING
Head gasket leaking Replace head gasket
\
\
\
\
\
\
\

Oil Light on at Low oil pump pressure Check oil pump
Idle operation, see ENGINES
Oil cooler or line Remove restriction
restricted and/or replace cooler
\
\
\
\
\
\
\

Engine Won't Injector pump fuel solenoid Remove and check
Shut Off does not return fuel valve solenoid and replace
to OFF position if needed
\
\
\
\
\
\
\

VACUUM PUMP DIAGNOSIS
Excessive Noise Loose pump-to-drive Tighten screws
assembly screws
Loose tube on pump assembly Tighten tube
Valves not functioning Replace valves
properly
Oil Leakage Loose end plug Tighten end plug
Bad seal crimp Remove and re-crimp
seal
\
\
\
\
\
\
\

FUEL INJECTION TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
BASIC FUEL INJECTION TROUBLE SHOOTING CHART
\
\
\
\
\
\
\

CONDITION POSSIBLE CAUSE CORRECTION\
\
\
\
\
\
\

Engine Won't Cold start valve inoperative Test valve and
Start (Cranks circuit
Normally)
Poor connection;vacuum or Check vacuum and
wiring electrical
connections
Contaminated fuel Test fuel for water
or alcohol
Defective fuel pump relay Test relay and
or circuit wiring
Battery too low Charge and test
battery

Load next 8 pages

Page: < prev 1-10 ... 9-16 17-24 25-32 33-40 41-48 next >

alternator child seat technical data wheel size gearbox headrest