1998 MITSUBISHI MONTERO cruise control

* PLEASE READ THIS FIRST *
NOTE: Self-diagnostics should be performed when cruise control
cancels without driver using normal cancel modes.
RETRIEVING CODES
1) Data Link Connector (DLC) is located to left of steering
column. Use analog voltmeter or scan tool for code retrieval. Follow
scan tool manufacturer's instructions.
2) Using an analog voltmeter, connect leads between cruise
control terminal and ground terminal of DLC. See Fig. 35. Count number
of deflections and pauses of voltmeter needle to determine trouble
code. Digit count is about 0.5 second per pulse and pause between
digits is about 2 seconds. Once trouble codes have been displayed, see
DIAGNOSTIC TROUBLE CODE (DTC) IDENTIFICATION table.
DIAGNOSTIC TROUBLE CODE (DTC) IDENTIFICATION TABLE









\









\









\









\









\









\






Code Diagnostic Item
11 .............................. Vacuum Pump Drive System
12 ........................... Vehicle Speed Sensor Signal
14 ....................... Vacuum Pump Power Supply System
15 ................................. Cruise Control Switch
16 .................................... Cruise Control ECU
17 ....................... Throttle Position Sensor System









\









\









\









\









\









\






Fig. 35: Identifying Data Link Connector Terminals
Courtesy of Mitsubishi Motor Sales of America
CLEARING CODES

1) To clear trouble codes, disconnect battery cable, or use
alternative method to prevent memory loss.
2) Turn ignition on. Turn main cruise control switch and SET
switch to ON position, and within one second, turn RES switch to ON
position. Hold stoplight switch and cruise control switch in ON
position for greater than 5 seconds. Verify codes are cleared.
DIAGNOSTIC TESTS
CODE 11: VACUUM PUMP DRIVE SYSTEM
Code 11 is displayed if release valve, control valve and
motor drive signals from vacuum pump are not input to cruise control
ECU. Probable causes are:
* Malfunction of vacuum pump.
* Malfunction of stoplight switch.
* Malfunction of connector.
* Malfunction of harness.
* Malfunction of cruise control ECU.
1) Check vacuum pump. See VACUUM PUMP TEST under COMPONENT
TESTS. If vacuum pump is defective, replace vacuum pump. If vacuum
pump is okay, go to next step.
2) Disconnect cruise control actuator harness connector A-57
or A-95. See Fig. 5. At harness side of connector, check voltage
between terminal No. 1 and ground. If battery voltage is present, go
to next step. If battery voltage is not present, check stoplight
switch. See BRAKELIGHT/STOPLIGHT SWITCH TEST under COMPONENT TESTS.
Replace switch if defective. Check cruise control main switch harness
connector C-01 and stoplight switch harness connector C-55. Repair as
necessary. If malfunction remains, check harness between cruise
control main switch and vacuum pump. Repair as necessary.
3) Disconnect cruise control ECU connector C-50. See Fig. 13.
At harness side of connector, check voltage between ground and
terminals No. 12 (driving release valve), No. 13 (driving control
valve), and No. 26 (driving motor). If battery voltage is present, go\
to next step. If battery voltage is not present, check and repair
connectors A-57 or A-95 and C-111 as necessary. See Figs. 5 and 24. If
malfunction remains, check and repair harness between vacuum pump and
cruise control ECU as necessary.
4) Check cruise control ECU connector C-50. Repair as
necessary. If malfunction remains, replace cruise control ECU.
CODE 12: VEHICLE SPEED SENSOR SIGNAL
Code 12 is displayed if vehicle speed signals from vehicle
speed sensor are not input to cruise control ECU when vehicle speed is
25 MPH or more. Probable causes are:
* Malfunction of VSS.
* Malfunction of connector.
* Malfunction of harness.
* Malfunction of cruise control ECU.
1) Check vehicle speed sensor. See VEHICLE SPEED SENSOR TEST
under COMPONENT TESTS. If speed sensor is okay, go to next step. If
speed sensor is defective, repair or replace as necessary.
2) Disconnect combination meter connector C-06. See Fig. 10.
At harness side of connector, with ignition switch in ON position,
measure voltage between terminal No. 1 and ground. If voltage is 4.5
volts or more, go to next step. If voltage is less than 4.5 volts,

check cruise control ECU connector C-50 and joint connector C-130.
Repair as necessary. See Figs. 13, 16 and 28. If malfunction remains,
check harness between combination meter (instrument cluster) and
cruise control ECU. Repair as necessary.
3) Disconnect combination meter connector C-04. See Fig. 9.
Check for continuity at harness side between terminal No. 43 and
ground. If continuity is present, go to next step. If continuity is
not present, check harness between combination meter and ground.
Repair as necessary.
4) Inspect combination meter connector C-04. If connector is
defective, repair as necessary. If connector is okay and malfunction
remains, replace cruise control ECU.
CODE 14: VACUUM PUMP POWER SUPPLY
Code 14 is displayed when drive signals for vacuum pump
release valve, control valve and motor are not input into cruise
control ECU. Probable causes are:
* Malfunction of stoplight switch.
* Malfunction of connector.
* Malfunction of harness.
* Malfunction of cruise control ECU.
1) Disconnect vacuum pump connector A-105. See Fig. 6. At
harness side of connector, check voltage between terminal No. 1 and
ground. If battery voltage is present, go to next step. If battery
voltage is not present, check stoplight switch. See
BRAKELIGHT/STOPLIGHT SWITCH TEST under COMPONENT TESTS. Replace as
necessary. If switch is okay, check connectors to combination meter,
stoplight switch and vacuum pump. Repair as necessary. If connectors
are okay and malfunction remains, check and repair circuit between
cruise control ECU and vacuum pump. If malfunction remains, replace
cruise control ECU.
2) Check connectors and circuit between cruise control ECU
and vacuum pump. See WIRING DIAGRAMS. Repair as necessary. If
connectors and circuit are okay, replace cruise control ECU.
CODE 15: CRUISE CONTROL SWITCH
Code 15 is displayed if RESUME switch or SET switch remains
on. Probable cause is malfunction of cruise control switch. Replace
cruise control switch.
CODE 16: CRUISE CONTROL ECU
Code 16 is displayed if there is an abnormality in CANCEL
hold circuit or microprocessor monitor circuit in cruise control ECU.
Probable cause is malfunction of cruise control ECU. Replace cruise
control ECU.
CODE 17: THROTTLE POSITION SENSOR
Code 17 is displayed if a voltage of 1.5 volts or more exists
when closed throttle position switch is ON or 0.2 volt or less exists
when closed throttle position switch is OFF for a continuous period of
4 seconds or more. Probable causes are:
* Malfunction of throttle position sensor.
* Malfunction of connector.
* Malfunction of harness.
* Malfunction of cruise control ECU.

1) If PCM DTC P0120 (engine performance code) is also set,
see
CLOSED THROTTLE POSITION SWITCH TEST & THROTTLE POSITION SENSOR TEST
under COMPONENT TESTS. If DTC P0120 is not set, go to next step.
2) Check cruise control ECU connector C-50. If connector is
okay, go to next step. If connector is defective, repair as necessary.
3) If malfunction remains, inspect harness between throttle
position sensor and cruise control ECU. Repair as necessary. If
harness is okay, replace cruise control ECU.
PIN VOLTAGE TESTS
Fig. 36: Pin Voltage Chart (1 Of 2)
Courtesy of Mitsubishi Motor Sales of America

* PLEASE READ THIS FIRST *
WARNING: Deactivate air bag system before performing any service
operation. See AIR BAG RESTRAINT SYSTEMS article. Do not
apply electrical power to any component on steering column
without first deactivating air bag system. Air bag may
deploy.
ACTUATOR
Removal & Installation
Disconnect cruise control cable from link. Disconnect
actuator wiring connector. Remove vacuum pump and vacuum pump bracket.
Remove actuator and actuator bracket. To install, reverse removal
procedure.
CRUISE CONTROL ECU
Removal & Installation
Cruise control ECU is located behind center of dash panel.
Remove center trim panel and radio or radio plug bezel. Remove control
unit. To install, reverse removal procedure.
CRUISE CONTROL SWITCH
Removal & Installation
Remove lower steering column cover. Disconnect electrical
connectors. Remove screws attaching cruise control switch to steering
column. Remove switch. To install, reverse removal procedure.
INSTRUMENT CLUSTER
Removal & Installation
Disconnect negative battery cable. Remove cluster cover.
Disconnect speedometer cable. Remove instrument cluster. To install,
reverse removal procedure.
WIRING DIAGRAMS

Fig. 38: Cruise Control System Wiring Diagram

MIXTURE. Perform all adjustments with engine at normal
operating temperature, front wheels in straight-ahead
position, cooling fan and all accessories off, and
transmission in Park or Neutral.
Eclipse 2.0L Non-Turbo
1) TP sensor is not adjustable. Disconnect TP sensor
connector. Using external ohmmeter, measure resistance between TP
sensor terminals No. 1 and 3. See Fig. 8. If resistance is not 3500-
6500 ohms, replace TP sensor.
2) While slowly rotating throttle valve from idle to full
open, measure resistance between TP sensor terminals No. 2 and 3. If
resistance does not change smoothly in proportion to throttle opening,
replace TP sensor.
Montero
1) Disconnect TP sensor connector. Using jumper wires,
connect an external ohmmeter between TP sensor terminals No. 1 and 2.
See Fig. 9 . Insert .025" (.65 mm) feeler gauge between fixed speed
adjusting screw and throttle lever.
2) Loosen TP sensor mounting screws and rotate TP sensor
fully clockwise. Ensure there is continuity between terminals No. 1
and 2. Rotate TP sensor counterclockwise until there is no continuity,
and tighten screws. Install Test Harness (MB991348) between TP sensor
and harness connector.
3) Turn ignition on. Using external voltmeter, measure TP
sensor output voltage between terminals No. 1 and 3. If voltage is not
.4-1.0 volt, check harness and sensor. See DTC P0120 in G - TESTS
W/CODES article.
All Other Models
1) Disconnect TP sensor connector. Using jumper wires,
connect an external ohmmeter between TP sensor terminals No. 1 and 2
on Diamante or No. 3 and 4 on all other models. See Fig. 9. On
Diamante and Mirage 1.8L with cruise control, insert .055" (1.40mm)
feeler gauge between fixed speed adjusting screw and throttle lever.
On Galant, insert .025" (.65 mm) feeler gauge between fixed speed
adjusting screw and throttle lever. On all other models, insert .018"
(.45 mm) feeler gauge between fixed speed adjusting screw and throttle\
lever.
2) Loosen TP sensor mounting screws and rotate TP sensor
fully counterclockwise. Ensure there is continuity between terminals
No. 1 and 2 on Diamante, or No. 3 and 4 on all other models. Rotate TP
sensor clockwise until there is no continuity and tighten screws.
Install Test Harness (MB991348) between TP sensor and harness
connector.
3) Turn ignition on. Using external voltmeter, measure TP
sensor output voltage between terminals No. 1 and 3 on Diamante, or
No. 2 and 4 on all other models. If voltage is not .4-1.0 volt, check
harness and sensor. See DTC P0120 in G - TESTS W/CODES article.
Fig. 8: TP Sensor Connector Terminals (Eclipse 2.0L Non-Turbo)
Courtesy of Mitsubishi Motor Sales of America

HO2S detects oxygen content in exhaust gas and sends this
information to PCM. PCM uses input signals from HO2S to vary duration
of fuel injection. HO2S heater stabilizes sensor temperature
regardless of exhaust gas temperature to allow for more accurate
exhaust oxygen content readings.
Idle Air Control (IAC) Valve Position Sensor
Sensor is incorporated in IAC motor. Sensor senses IAC motor
plunger position and sends electrical signal to PCM.
Ignition Timing Adjustment Terminal
Used for adjusting base ignition timing. When terminal is
grounded, PCM timing control function is by-passed, allowing base
timing to be adjusted.
Intake Air Temperature (IAT) Sensor
IAT sensor is incorporated into airflow sensor assembly. This
resistor-based sensor measures temperature of incoming air and
supplies air density information to PCM.
Knock Sensor (KS)
KS is located in cylinder block and senses engine vibration
during detonation (knock). KS converts vibration into electrical
signal. PCM retards ignition timing based on this signal.
Manifold Differential Pressure (MDP) Sensor
MDP sensor converts negative air pressure in intake manifold
plenum into voltage signals sent to PCM. PCM monitors Exhaust Gas
Recirculation (EGR) system using these signals.
Park/Neutral Position (PNP) Switch (Automatic Transmission)
PNP switch senses position of transmission select lever,
indicating engine load due to automatic transmission engagement. Based
on this signal, PCM commands IAC motor to increase throttle angle,
maintaining optimum idle speed.
Power Steering Oil Pressure Switch
Switch detects increase in power steering oil pressure. When
power steering oil pressure increases, switch contacts close,
signaling PCM. PCM commands IAC motor, raising idle speed to
compensate for drop in engine RPM due to power steering load.
Throttle Position (TP) Sensor
TP sensor is a variable resistor mounted on throttle body.
PCM uses voltage signal from TP sensor to determine throttle plate
angle.
Vehicle Speed Sensor (VSS)
Mounted on transaxle/transmission, VSS sends a pulsing signal
to PCM for vehicle speed calculation. PCM uses this calculation for
cruise control and fuel cut-off.
Volume Airflow (VAF) Sensor
Incorporated into airflow sensor assembly, VAF sensor
measures intake airflow rate. Intake air flows through tunnel in
airflow sensor assembly. VAF sensor sends frequency signal to PCM. PCM
uses signal to adjust fuel injection rate.
OUTPUT SIGNALS
NOTE: Vehicles are equipped with various combinations of
computer-controlled components. Not all components listed
below are used on every vehicle. To determine component