1998 MITSUBISHI MONTERO light

Symptom Inspection Procedure
Communication With All Systems Not Possible ............ 1
Communication With SRS Only Not Possible ............... 2
Ignition Switch On (Engine Stopped)
SRS Warning Light Does Not Come On ............... DTC 43
SRS Warning Light Stays On After 7 Seconds ...... DTC 43









\









\









\









\









\









\







INSPECTION PROCEDURE 1
The cause is probably in power supply system (including
ground circuit of diagnostic line). Check connectors and harness, and
repair if necessary.
INSPECTION PROCEDURE 2
NOTE: Refer to WIRING DIAGRAMS for connector identification.
1) Before proceeding, see SERVICE PRECAUTIONS. Deactivate
SRS. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Measure SRS Check Harness (MB991613) connector No. 5.
Disconnect SRS-ECU connector C-122 and connect SRS check harness
connector No. 3 to C-122. Check continuity between terminal No. 20, 21
and ground. If there is no continuity, go to next step. If there is
continuity, go to step 4).
3) Check connector C-122, and repair if necessary. If
connector is okay, check for trouble symptoms. If fault exists, check
harness between SRS-ECU and ground, and repair if necessary.
4) Measure SRS check harness connector No. 5. Disconnect SRS-
ECU connector C-122 and connect SRS harness check connector No. 3 to
C-122. Connect negative battery cable. Measure voltage between
terminal No. 13 and 14, and body ground. If voltage at terminals is 9
volts or more, check harness wire between SRS-ECU and Data Link
Connector (DLC), and repair if necessary. If harness wire is okay,
replace SRS-ECU. See SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL &
INSTALLATION. If voltage is not as specified, check connector C-80, C-
93, C-101, and C-132, and repair if necessary. If connectors are okay,
check for trouble symptoms. If fault exists, check harness between
SRS-ECU and IG1 A or B (ignition switch), and repair if necessary.
Fig. 10: Identifying SRS Check Harness (MB991613) Connectors
Courtesy of Mitsubishi Motor Sales of America.
DTC 11, 12 & 13: FRONT IMPACT SENSOR SYSTEM

cause accidental air bag deployment and personal injury.
NOTE: Refer to WIRING DIAGRAMS for connector identification.
1) Before proceeding, see SERVICE PRECAUTIONS. Deactivate
SRS. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Disconnect passenger-side air bag connector C-107. Connect
SRS Check Harness (MB991613) connector No. 1 to passenger-side air bag\
connector. Erase DTC memory and check if DTCs 24, 25, or 64 are set.
If any of these DTCs are output, go to next step. If DTCs are not
output, replace passenger-side air bag module. See
PASSENGER-SIDE AIR BAG MODULE under REMOVAL & INSTALLATION.
3) Check connectors C-107 and C-122, and repair if necessary.
If connectors are okay, check trouble symptoms. If fault is still
present, check harness wire between passenger-side air bag module and
SRS-ECU, and repair if necessary. If harness wire is okay, replace
SRS-ECU. See SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL &
INSTALLATION.
DTC 31 & 32: SRS-ECU CAPACITOR SYSTEM
Before proceeding, see SERVICE PRECAUTIONS. Replace SRS-ECU.
See SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL & INSTALLATION.
DTC 34: CONNECTOR LOCK SYSTEM
NOTE: If vehicle condition returns to normal, DTC will be erased
and SRS warning light will return to normal.
NOTE: Refer to WIRING DIAGRAMS for connector identification.
Before proceeding, see SERVICE PRECAUTIONS. Check connector
C-122 and repair if necessary. If connector is okay, check for trouble
symptom. If fault exists, replace SRS-ECU. See
SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL & INSTALLATION.
DTC 35: SRS-ECU SYSTEM (AFTER AIR BAG DEPLOYMENT)
Before proceeding, see SERVICE PRECAUTIONS. Replace SRS-ECU.
See SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL & INSTALLATION.
DTC 41: IG1 (A) POWER CIRCUIT SYSTEM
NOTE: If vehicle condition returns to normal, DTC will be erased
and SRS warning light will return to normal.
NOTE: Refer to WIRING DIAGRAMS for connector identification.
1) Before proceeding, see SERVICE PRECAUTIONS. Deactivate
SRS. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Measure SRS Check Harness (MB991613) connector No. 5.
Disconnect SRS-ECU connector C-122 and connect SRS check harness
connector No. 3 to C-122. Check terminal No. 20 and 21 for continuity
to ground. If there is no continuity, go to next step. If there is
continuity, go to step 4).
3) Check connector C-122 and repair if necessary. If
connector is okay, check for trouble symptom. If fault exists, check
harness wire between SRS-ECU and ground, and repair if necessary.
4) Measure SRS check harness connector No. 5. Disconnect SRS-
ECU connector C-122 and connect SRS harness check connector No. 3 to
C-122. Connect negative battery cable and turn ignition switch to ON
position. If voltage between terminal No. 14 and body ground is 9

volts or more, replace SRS-ECU. See SRS AIR BAG CONTROL UNIT (ECU)
under REMOVAL & INSTALLATION. If voltage is not as specified, check
connector C-93, C-101, and C-132, and repair if necessary. If
connectors are okay, check for trouble symptoms. If fault still
exists, check harness wire between SRS-ECU and ignition switch IG1
(A), and repair if necessary.
DTC 42: IG1 (B) POWER CIRCUIT SYSTEM
NOTE: If vehicle condition returns to normal, DTC will be erased
and SRS warning light will return to normal.
NOTE: Refer to WIRING DIAGRAMS for connector identification.
1) Before proceeding, see SERVICE PRECAUTIONS. Deactivate
SRS. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Measure SRS Check Harness (MB991613) connector No. 5.
Disconnect SRS-ECU connector C-122 and connect SRS check harness
connector No. 3 to C-122. Check terminal No. 20 and 21 for continuity
to ground. If there is no continuity, go to next step. If there is
continuity, go to step 4).
3) Check connector C-122 and repair if necessary. If
connector is okay, check for trouble symptoms. If fault still exists,
check harness wire between SRS-ECU and ground, and repair if
necessary.
4) Measure SRS check harness connector No. 5. Disconnect SRS-
ECU connector C-122 and connect SRS harness check connector No. 3 to
C-122. Connect negative battery cable and turn ignition switch to ON
position. If voltage between terminal No. 13 and body ground is 9
volts or more, replace SRS-ECU. See SRS AIR BAG CONTROL UNIT (ECU)
under REMOVAL & INSTALLATION. If voltage is not as specified, check
connector C-80, C-93, and C-101, and repair if necessary. If
connectors are okay, check for trouble symptoms. If fault still
exists, check harness wire between SRS-ECU and ignition switch IG1
(B), and repair if necessary.
DTC 43: SRS WARNING LIGHT CIRCUIT
NOTE: Refer to WIRING DIAGRAMS for connector identification.
Light Does Not Come On
1) Before proceeding, see SERVICE PRECAUTIONS. Deactivate
SRS. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Measure SRS Check Harness (MB991613) connector No. 5.
Disconnect SRS-ECU connector C-122 and connect SRS check harness
connector No. 3 to C-122. Check terminal No. 20 and 21 for continuity
to ground. If there is no continuity, go to next step. If there is
continuity, go to step 4).
3) Check connector C-122 and repair if necessary. If
connector is okay, check for trouble symptoms. If fault still exists,
check harness wire between SRS-ECU and ground, and repair if
necessary.
4) Measure SRS check harness connector No. 5. Disconnect SRS-
ECU connector C-122 and connect SRS harness check connector No. 3 to
C-122. Connect negative battery cable and turn ignition switch to ON
position. Connect terminal No. 15 to body ground. If SRS warning light
comes on, replace SRS-ECU. See SRS AIR BAG CONTROL UNIT (ECU) under
REMOVAL & INSTALLATION. If SRS warning light does not come on, inspect
for blown bulb and repair if necessary. If bulb is okay, check
connector C-04, C-11, C-96, and C-101, and repair if necessary. If
connectors are okay, check for trouble symptoms. If fault still
exists, check harness wire between SRS-ECU and ignition switch IG1,
and repair if necessary. If harness wire is okay, replace combination

meter.
Light Does Not Turn Off
1) Before proceeding, see SERVICE PRECAUTIONS. Connect
negative battery cable and turn ignition switch to ON position. If SRS
warning light stays on when C-122 is disconnected, go to next step. If
SRS warning light turns off when C-122 is disconnected, replace SRS-
ECU. See SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL & INSTALLATION.
2) Check connector C-122, and repair if necessary. If
connector is okay, check trouble symptoms. If fault still exists,
check wire harness between SRS-ECU and combination meter, and repair
if necessary.
DTC 44: SRS WARNING LIGHT DRIVE CIRCUIT SYSTEM
NOTE: If vehicle condition returns to normal, DTC will be erased
and SRS warning light will return to normal.
Before proceeding, see SERVICE PRECAUTIONS. Check SRS warning
light drive circuit system. If warning light drive system is okay,
replace SRS-ECU. See SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL &
INSTALLATION. Check for DTCs. See SYSTEM OPERATION CHECK.
DTC 45: SRS-ECU EEPROM & A/D CONVERTER SYSTEM
Before proceeding, see SERVICE PRECAUTIONS. Replace SRS-ECU.
See SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL & INSTALLATION.
DTC 51 & 52: DRIVER-SIDE AIR BAG MODULE (SQUIB IGNITION
DRIVE CIRCUIT) SYSTEM
Before proceeding, see SERVICE PRECAUTIONS. Replace SRS-ECU.
See SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL & INSTALLATION.
DTC 54 & 55: PASSENGER-SIDE AIR BAG MODULE (SQUIB
IGNITION DRIVE CIRCUIT) SYSTEM
Before proceeding, see SERVICE PRECAUTIONS. Replace SRS-ECU.
See SRS AIR BAG CONTROL UNIT (ECU) under REMOVAL & INSTALLATION.
COMPONENT TESTING
CLOCKSPRING TEST
1) Before proceeding, see SERVICE PRECAUTIONS. Deactivate
system. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Remove driver-side air bag module and clockspring. See
DRIVER-SIDE AIR BAG MODULE & CLOCKSPRING under REMOVAL & INSTALLATION.
Check connectors, protective tubing, and case for damage, and
terminals for deformities. Check for continuity between No. 1
connector of clockspring and connectors No. 3 and 4. See Figs. 12 and
13.
3) Align paint mark of SRS Check Harness (MB991613) connecto\
r
No. 4 with notch in clockspring connector No. 2 and connect. See
Fig. 14 . Check continuity between terminals No. 22 and 23 of SRS check
harness connector No. 5. See Fig. 13.
4) Replace clockspring if any damage was found or continuity
does not exist between specified terminals. See
DRIVER-SIDE AIR BAG MODULE & CLOCKSPRING under REMOVAL & INSTALLATION.

ANTI-LOCK BRAKE SYSTEM
1998 Mitsubishi Montero
1997-98 BRAKES
Mitsubishi - Anti-Lock
Montero
DESCRIPTION
CAUTION: See ANTI-LOCK BRAKE SAFETY PRECAUTIONS article in GENERAL
INFORMATION.
NOTE: For more information on brake system, see BRAKE SYSTEM
article.
The Anti-Lock Brake System (ABS) is designed to prevent wheel\
lock-up during heavy braking. This allows operator to maintain
steering control while stopping vehicle in shortest distance possible.
Major components are a hydraulic unit, wheel speed sensors, "G"
sensor, ABS Electronic Control Unit (ECU) and ANTI-LOCK warning light.\
ABS has a self-diagnostic system to indicate a system malfunction and
for use in system trouble shooting.
OPERATION
Each wheel sensor sends an AC electrical signal to the ECU.
The ECU reads this information as wheel speed. When any decelerating
wheel speed rate is determined to be excessive in comparison to other
monitored wheels, the hydraulic unit cycles hydraulic brake pressure
to each wheel to equalize speed of all wheels. ABS turns itself off
when vehicle drops to 4 MPH. Minor lock-up may occur at this point.
With engine running and vehicle speed greater than 4 MPH,
pump motor will operate for a short period of time and may be heard
inside vehicle. During pump motor operation, ABS system is completing
a self-check. During ABS system operation, a pulsing brake pedal and
vibration in steering wheel and vehicle body may be experienced. These
conditions are normal.
BLEEDING BRAKE SYSTEM
BLEEDING PROCEDURES
CAUTION: When adding brake fluid, ensure filter is properly fitted on
reservoir tank.
ABS system is bled using conventional method. With engine
running, manually bleed system using an assistant. For bleeding order,
see BRAKE LINE BLEEDING SEQUENCE table. Ensure Load Sensing
Proportioning Valve (LSPV) is bled in sequence. Remove all air from
brake system. Refill brake fluid reservoir after bleeding procedure is
complete.
BRAKE LINE BLEEDING SEQUENCE









\









\









\









\









\









\









\







Application Sequence
Montero ....................................... RR, LR, LSPV, RF, LF









\









\









\









\









\









\









\

ADJUSTMENTS
* PLEASE READ FIRST *
NOTE: For adjustment information on brake pedal height, free play,
parking brake and stoplight switch, see BRAKE SYSTEM article.
WHEEL SPEED SENSOR (WSS)
NOTE: Rear WSS gap adjustment information is not available from
manufacturer.
Front WSS-To-Rotor Gap Adjustment
1) Raise and support vehicle. Remove wheel(s). Inspect senso\
r
pole piece for damage. Repair if necessary. If sensor pole piece is
okay, check WSS-to-rotor gap.
2) Using a feeler gauge, check clearance between sensor pole
and rotor tooth surface. See Fig. 1. Front WSS sensor clearance should
be .008-.390" (0.2-1.0 mm). If clearance is not as specified, loosen
sensor mounting bolt. Adjust sensor position until clearance is within
specification. Tighten sensor mounting bolt to specification. See
TORQUE SPECIFICATIONS .
Fig. 1: Checking Front WSS-To-Rotor Gap
Courtesy of Mitsubishi Motor Sales of America.
TROUBLE SHOOTING
ANTI-LOCK WARNING LIGHT
1) Turn ignition on. ANTI-LOCK warning light should come on

for one second, and then go out. Turn ignition switch to START
position. Warning light should come on and stay on.
2) When ignition switch is turned from START to ON position,
warning light should come on for one second, and then go out. If
warning light functions as specified, go to step 3). If warning light
does not function as specified, see appropriate trouble shooting test:
* IGNITION SWITCH IN ON POSITION (ENGINE NOT RUNNING),
ANTI-LOCK WARNING LIGHT INOPERATIVE
* AFTER ENGINE STARTS, ANTI-LOCK WARNING LIGHT REMAINS ON
* IGNITION SWITCH IN START POSITION, ANTI-LOCK WARNING LIGHT
INOPERATIVE
* IGNITION SWITCH IN ON POSITION, ANTI-LOCK WARNING LIGHT
BLINKS TWICE. IN START POSITION, LIGHT STAYS ON. WHEN
IGNITION SWITCH IS CYCLED FROM START TO ON POSITION, LIGHT
BLINKS ONCE, THEN TURNS OFF
3) Test drive vehicle. If ANTI-LOCK warning light does not
come on at low speed, go to next step. If light comes on at low speed,
motor relay, solenoid valve or Wheel Speed Sensor (WSS) malfunction is\
indicated. Go to step 6). If insufficient braking force or ABS
malfunction exists, go to next step. If none of listed symptoms exist,
go to step 6).
4) Check conventional brake system components for proper
operation. Check for mechanical lock of hydraulic unit solenoid valve.
Check for plugged hydraulic line in hydraulic unit. Repair or replace
as necessary. If hydraulic unit is okay, go to next step.
5) Ensure WSS rotor gap is correct. See WHEEL SPEED SENSOR
(WSS) under ADJUSTMENTS. Check for faulty wheel speed sensor. See
WHEEL SPEED SENSOR (WSS) under COMPONENT TESTS. Replace sensor as
necessary. See WHEEL SPEED SENSOR (WSS) under REMOVAL & INSTALLATION.
Inspect ECU connectors and related wiring harness. See WIRING DIAGRAMS
. If testing indicates no mechanical or electrical failures,
substitute ECU with known-good unit and retest.
6) Enter ABS self-diagnostics and retrieve Diagnostic Trouble
Codes (DTCs). See RETRIEVING DTCs under SELF-DIAGNOSTIC SYSTEM. If no
DTCs are displayed, fault may be intermittent. Attempt to make
malfunction reoccur. If no diagnostic output exists, check and repair
wiring harness between ECU and data link connector. See
WIRING DIAGRAMS .
NOTE: Trouble shoot ANTI-LOCK warning light in following sequence:
instrument cluster circuit, ECU and valve relay.
Ignition Switch In ON position (Engine Not Running),
ANTI-LOCK Warning Light Inoperative
1) If all other warning lights come on with ignition on, go
to step 3). If other warning lights do not come on, check fuse No. 11
in main fuse panel. If fuse is blown, correct cause of blown fuse, and
replace fuse. If fuse is okay, go to next step.
2) Remove instrument cluster. Turn ignition on. Using DVOM,
check voltage between vehicle ground and instrument cluster ANTI-LOCK
warning light terminal No. 28. See Fig. 2. If light does not come on,
go to next step. If light comes on, check and repair connectors and
related wiring harness between instrument cluster, ABS valve relay and
ECU. See WIRING DIAGRAMS .
3) Turn ignition off. Check for faulty warning light bulb.
Replace bulb as necessary. If bulb is okay, check and repair
connectors and related wiring harness between instrument cluster and
ECU. See WIRING DIAGRAMS . If connectors and wiring are okay, replace
instrument cluster.

Fig. 2: Identifying Instrument Cluster Connector Terminals
Courtesy of Mitsubishi Motor Sales of America.
After Engine Starts, ANTI-LOCK Warning Light Remains On
1) With ignition on, disconnect instrument cluster
connectors. If warning light remains on, replace instrument cluster.
If warning light goes off, go to next step.
2) Disconnect ECU 22-pin connector and ABS relay box 8-pin
connector. See Fig. 3. If warning light goes off, replace ECU. If
warning light stays on, check and repair connectors and related wiring
harness between ECU, instrument cluster, and ABS valve relay. See
WIRING DIAGRAMS .
Fig. 3: Exploded View Of Hydraulic Unit & Components
Courtesy of Mitsubishi Motor Sales of America.
Ignition Switch In START Position, ANTI-LOCK Warning Light
Inoperative