1998 MITSUBISHI MONTERO instrument cluster

NOTE: The following information only applies to Eclipse and Galant.
NOTE: Perform INPUT SIGNAL INSPECTION before proceeding with
SYSTEM TESTS. To identify circuit connector terminals, see
WIRING DIAGRAMS .
Communication With All Systems Not Possible (Eclipse &
Galant)
1) Check voltage between ground and Data Link Connector (DLC)\
terminal No. 16 (Red/Black wire on Eclipse or Brown/Red wire on
Galant). See Fig. 1. If battery voltage is present, go to step 3). If
battery voltage is not present, go to next step.
2) Check junction block connectors between DLC and power
supply. See WIRING DIAGRAMS . If connectors are okay, check circuit
between power supply and DLC. See WIRING DIAGRAMS. Repair as
necessary.
3) Check continuity between ground and DLC terminals No. 4
and 5. If continuity is present, replace scan tool and retest. If
continuity is not present, check circuit between ground and DLC. See
WIRING DIAGRAMS . Repair as necessary.
Communication With One-Shot Pulse Input Signal Only Is Not
Possible (Eclipse & Galant)
Check circuit between DLC and junction block No. 1. See
WIRING DIAGRAMS . Repair as necessary. If circuit is okay, check
harness connectors to ETACS-ECU, DLC and junction/joint connectors.
Repair as necessary. If connectors are okay, replace ECU.
Defogger Does Not Operate With Defogger Switch ON (Eclipse &
Galant)
1) Check defogger switch input signal. See
INPUT SIGNAL INSPECTION . If switch input signal is okay, check
defogger circuit and relay. See DEFOGGER RELAY TEST under COMPONENT
TESTS. Repair or replace as necessary. If switch input signal is not
okay, go to next step.
2) Check defogger switch. See DEFOGGER SWITCH TEST under
COMPONENT TESTS. Replace as necessary. If defogger switch is okay,
turn ignition on. Check voltage between ground and defogger switch
harness-side connector terminal No. 4 (Eclipse) or terminal No. 2
(Galant). See WIRING DIAGRAMS . If voltage reading is 5 volts (Eclipse)
or battery voltage (Galant), go to next step. If voltage reading is
not as specified, go to step 4).
3) Check joint/junction connectors between switch, instrument
panel cluster and ETACS-ECU. See WIRING DIAGRAMS. Repair as necessary.
If connectors are okay, check circuit between defogger switch and
ground. Repair as necessary. If circuit is okay, replace ECU.
4) Check harness connectors to ETACS-ECU and instrument panel
cluster. Repair as necessary. If connectors are okay, check circuit
between ECU and defogger switch. Repair as necessary.
Defogger Relay Circuit System Check (Eclipse & Galant)
1) Check defogger relay. See DEFOGGER RELAY TEST under
COMPONENT TESTS. Replace as necessary. If relay is okay, go to next
step.
2) Check voltage between ground and relay harness-side
connector terminals No. 3 and 5. See WIRING DIAGRAMS. If battery
voltage is present, go to next step. If battery voltage is not
present, go to step 4).
3) Check harness connectors to relay, ETACS-ECU, junction
block and rear wiring/liftgate. See WIRING DIAGRAMS. Repair as
necessary. If connectors are okay, check circuit between defogger
relay and rear defogger, defogger and ground, or defogger relay and
ECU. See WIRING DIAGRAMS . Repair as necessary. If circuits are okay,

NOTE: Remove window defogger switch and disconnect switch
connector for the following test.
Diamante
Rear window defogger is integral with and controlled by A/C
system ECU. To diagnose system, refer to AIR CONDITIONING & HEATING
SERVICE & REPAIR article.
Eclipse
Turn defogger switch to OFF position. Using ohmmeter, check
switch continuity. Continuity should be present between terminals No.
1 and 3, and terminals No. 2 and 6. Turn defogger switch to ON
position. Continuity should be present between terminals No. 1, 3 and
4, and between terminals No. 2 and 6. See Fig. 5. If continuity is not
as specified, replace switch.
Galant
Turn defogger switch to OFF position. Using ohmmeter, check
switch continuity. Continuity should be present between terminals No.
1 and 3. Turn defogger switch to ON position. Continuity should exist
between terminals No. 2, 4 and 6, and between terminals No. 1 and 3.
See Fig. 5 . If continuity is not as specified, replace switch.
Mirage
Turn defogger switch to OFF position. Using ohmmeter, check
switch continuity. Continuity should be present between terminals No.
1 and 3, and terminals No. 2 and 6. Turn defogger switch to ON
position. Continuity should exist between terminals No. 1 and 3, and
terminals No. 2, 4, 5 and 6. See Fig. 5. If continuity is not as
specified, replace switch.
Montero
Turn defogger switch to OFF position. Using ohmmeter, check
switch continuity. Continuity should be present between terminals No.
1 and 3, and terminals No. 4 and 5. Turn defogger switch to ON
position. Continuity should exist between terminals No. 1 and 3,
terminals No. 4 and 5, and between terminals No. 2 and 6. See Fig. 5.
If continuity is not as specified, replace switch.
Montero Sport
Turn defogger switch to OFF position. Using ohmmeter, check
switch continuity. Continuity should be present between terminals No.
1 and 5, and terminals No. 2 and 6. Turn defogger switch to ON
position. Continuity should be present between terminals No. 3 and 4,
terminals No. 1 and 5, and between terminals No. 2 and 6. See Fig. 5.
If continuity is not as specified, replace switch.
3000GT
1) Remove defogger switch assembly from instrument cluster
bezel. With defogger switch in OFF position, check switch continuity
using ohmmeter.
2) Continuity should exist between terminals No. 3 and 4.
With defogger switch in ON position, continuity should exist between
terminals No. 1 and 2, terminals No. 1 and 6, and between terminals
No. 3 and 4. See Fig. 6. If continuity is not as specified, replace
switch.
Fig. 5: Identifying Defogger Switch Terminals (Eclipse, Galant,
Mirage, Montero & Montero Sport)
Courtesy of Mitsubishi Motor Sales of America

At heater unit, remove center air outlet cool air by-pass
lever cable from damper lever. To remove center air outlet, push
springs at bottom of center air outlet upward. Outlet is located above
radio. Remove switch from center air outlet. To install, reverse
removal procedure. Turn cool air by-pass lever on outlet fully upward.
Pull air by-pass lever fully downward and install cool air by-pass
lever cable to damper lever.
Removal & Installation (Mirage)
Remove driver-side lower dash panel. Remove center console
assembly and foot distribution duct. Disconnect rear window defogger
switch harness connector. Remove switch. To install, reverse removal
procedure.
Removal & Installation (Montero)
Remove defogger switch by prying switch off instrument
cluster bezel. Disconnect wiring harness from defogger switch. Remove
switch. To install, reverse removal procedure.
Removal & Installation (Montero Sport)
Remove instrument cluster bezel. Bezel is held in by metal
clips. Disconnect wiring harness from defogger switch. Remove switch
from behind bezel. To install, reverse removal procedure.
Removal & Installation (3000GT)
Remove knee protector. Remove steering column upper and lower
covers. Remove instrument cluster bezel. Disconnect wiring harness
from defogger switch. Remove defogger switch. To install, reverse
removal procedure.
WIRING DIAGRAMS

* PLEASE READ THIS FIRST *
WARNING: To avoid injury from accidental air bag deployment, read and
carefully follow all SERVICE PRECAUTIONS and DISABLING &
ACTIVATING AIR BAG SYSTEM procedures in AIR BAG RESTRAINT
SYSTEM article.
CAUTION: When removing or installing floor console, DO NOT allow any
impact or shock to Supplemental Restraint System Electronic
Control Unit (SRS-ECU).
FRONT HEATER UNIT & HEATER CORE
Removal
1) Deactivate air bag system. See AIR BAG RESTRAINT SYSTEM
article. Remove front and rear floor consoles. Remove hood release
handle. Remove fuel door release handle. Remove knee protector and
support brackets. Remove speaker covers.
NOTE: On A/T models, when removing front floor console, set A/T
selector lever in "L" position.
2) Remove glove box door stop, glove box and glove box frame.
Remove passenger-side air bag module. Remove heater control panel
cover. Remove heater control panel and radio. Remove plug from
instrument cluster cover. Remove instrument cluster cover and
instrument cluster.
3) Remove steering column cover. Remove clock or plug. Remove
side defroster covers. Remove side mirror control switch. Remove front
speakers.
4) Remove rheostat, rear wiper/washer switch, and door lock
switch. Disconnect ventilation control cable and harness connector.
See Fig. 9. Remove instrument panel. See INSTRUMENT PANEL. Drain
coolant and disconnect heater hoses from heater unit.
5) Remove shower ducts, lap duct, joint duct and center duct.
See Fig. 1 . Remove center reinforcement. Remove heater unit. Remove
distribution duct. Remove heater core.
Installation
Install heater core, distribution duct, heater unit and
center reinforcement. Install remaining ducts in reverse order of
removal. Install instrument panel. Tighten steering column bolts to 16
ft. lbs. (22 N.m). Install and adjust ventilation control cable. See
ADJUSTMENTS . To complete installation, reverse removal procedure. Add
coolant and check for leaks.
INSTRUMENT PANEL
Removal & Installation
Remove instrument panel components and then instrument panel,
in order listed on appropriate illustration. See Fig. 9. To install,
reverse removal procedures.

Starters
Generator .................................. Generators & Regulators
Engine Performance
Power Distribution
Generic Electronic Module (GEM) ............... Body Control Modules\
Electronic Suspension
Glow Plug Relay ................................. Engine Performance
Glow Plugs ...................................... Engine Performance
Grounds ........................................ Ground Distribution
Headlight Door Module .............................. Headlight Doors
Headlight Relay .................................. Headlight Systems
Daytime Running Lights
Headlights ....................................... Headlight Systems
Daytime Running Lights
Heated Oxygen Sensor(s) (HO2S) .................. Engine Performan\
ce
Heated Windshield Control Module ................ Heated Windshields
Height Sensor ................................ Electronic Suspension
Horns ..................................... Steering Column Switches
Horn Relay ................................ Steering Column Switches
Idle Air Control (IAC) Motor/Valve .............. Engine Performance\
Ignition Coil(s) ................................ Engine Performance\
Ignition Key Lock Cylinder ....................... Anti-Theft System
Ignition Module ................................. Engine Performance
Ignition Switch ................................. Power Distribution
Engine Performance
Generators & Regulators
Starters
Illuminated Entry Module .............. Illumination/Interior Lights
Illumination Lights ................... Illumination/Interior Lights
Impact Sensor ............................. Air Bag Restraint System
Inertia Fuel Shutoff Switch ..................... Engine Performance
Inhibit Relay ............................................. Starters
Instrument Cluster ........................ Analog Instrument Panels
Intake Air Temperature (IAT) Sensor ............. Engine Performance\
Interior Lights ....................... Illumination/Interior Lights
Interlock Switch .......................................... Starters
Junction Block .................................. Power Distribution
Keyless Entry Receiver ........................ Remote Keyless Entry
Key Reminder Switch ....................................... Starters
Knock Sensor .................................... Engine Performance
Lamp Control Module ................................ Exterior Lights
License Plate Lamp ................................. Exterior Lights
Lighting Control Module ................... Lighting Control Modules
Anti-Theft System
Daytime Running Lights
Headlight Systems
Lower Relay .................................. Power Convertible Top
Malfunction Indicator Light (MIL) ............... Engine Performance\
Instrument Panels
Manifold Absolute Pressure (MAP) Sensor ......... Engine Performance\
Mass Airflow (MAF) Sensor ....................... Engine Performance\
Mega Fuse .................................. Generators & Regulators
Memory Seat/Mirror Module ........................... Memory Systems
Mirror Defogger ............................... Rear Window Defogger
Moon Roof Motor .................................... Power Moon Roof
Moon Roof Relay .................................... Power Moon Roof
Multi-Function Control Module ...................... Warning Systems
Neutral Safety Switch ..................................... Starters
Oil Level Switch ................................ Engine Performance
Oil Pressure Switch/Sending Unit .......... Analog Instrument Panels
Engine Performance
Overhead Console .................................. Overhead Console
Oxygen Sensor(s) (O2S) .......................... Engine Performan\
ce

INSTRUMENT PANEL
1998 Mitsubishi Montero
1998 ACCESSORIES & EQUIPMENT
Mitsubishi - Instrument Panels
Eclipse, Galant, Mirage, Montero, Montero Sport, 3000GT
DESCRIPTION & OPERATION
WARNING: Deactivate air bag system before performing any service
operation. See AIR BAG RESTRAINT SYSTEMS article. Do not
apply electrical power to any component on steering column
without first deactivating air bag system. Air bag may
deploy.
Instrument cluster includes speedometer, fuel gauge and
temperature gauge. Fuel gauge has a built-in voltage limiter to keep
voltage supply to gauges at 7 volts. Some models may also have an
ammeter, oil pressure gauge, tachometer, voltmeter and/or turbo boost
pressure gauge. Oil pressure gauge uses full battery voltage.
Tachometer operates by pulse feed.
COMPONENT LOCATIONS
COMPONENT LOCATIONS TABLE








\









\









\









\









\









\






Component Location
Engine Coolant Temperature (ECT) Sensor
Eclipse, Galant, Montero
& Montero Sport ................. On Thermostat Housing
Mirage ........................ On Rear Of Cylinder Head
3000GT ........... On Cylinder Head, Below Ignition Coil
Input Speed Sensor
Eclipse ........................... On Side Of Transaxle
Output Speed Sensor
Eclipse ........................... On Side Of Transaxle
Vehicle Speed Sensor
Eclipse, Galant,
Mirage & 3000GT ................... On Top Of Transaxle
Montero & Montero Sport ...... On Transmission Tailshaft









\









\









\









\









\









\






TROUBLE SHOOTING
FUEL/TEMPERATURE GAUGE NOT WORKING
Check for blown fuse, faulty voltage limiter and faulty
relay. Ensure sending unit connections are clean and tight. Test
sending unit for correct operation. Tighten connections in instrument
cluster.
SPEEDOMETER NOT WORKING
On mechanical-type speedometers, ensure speedometer cable is
properly connected and correctly routed. If speedometer pointer and/or
odometer still do not work, replace speedometer cable or speedometer
assembly.
On electric-type speedometers, check for faulty vehicle speed
sensor, input/output sensors or faulty circuit. For testing, see

SPEEDOMETER TEST under COMPONENT TESTS. Repair or replace as
necessary.
TACHOMETER NOT WORKING
Tachometer is serviced as an assembly. If wiring harness is
okay, replace tachometer assembly.
WARNING LIGHTS NOT WORKING
Test for defective sending unit, burned-out bulb and broken
printed circuit. Ensure all connections are clean and tight.
COMPONENT TESTS
BOOST PRESSURE GAUGE (TURBO)
Resistance Test (Eclipse & 3000GT)
1) Remove instrument cluster from instrument panel. See
INSTRUMENT CLUSTER under REMOVAL & INSTALLATION. On 3000GT, remove air
distribution duct and combination gauges.
2) On all models, check resistance between boost pressure
gauge terminals on back of instrument cluster or combination gauges.
See Fig. 1 or 2. Resistance should be 68.2-83.4 ohms on Eclipse, or 72
ohms on 3000GT. If resistance is not as specified, replace gauge.
Fig. 1: Boost Pressure Gauge Test Terminals (Eclipse Turbo)
Courtesy of Mitsubishi Motor Sales of America

Fig. 9: Identifying Fuel Gauge Test Connections (3000GT)
Courtesy of Mitsubishi Motor Sales of America
NOTE: Fuel gauge resistance test must be completed with instrument
panel cluster removed. Use ohmmeter for all measurements. If
resistance is extremely low, a short may exist in coil. If
resistance is extremely high, a broken wire or similar