1998 MITSUBISHI MONTERO center console

than 0.5 volt or more than 4.5 volts, or an open or short
circuit in "G" sensor system.
1) Disconnect "G" sensor connector. Sensor is located on
bracket under center console, next to shifter. See Fig. 10. Connect
Special Tool (MB991348) between sensor and connector. Using a DVOM,
check voltage between sensor connector terminals No. 2 (Blue/White
wire) and No. 3 (Black/Red wire). Voltage should be 2.38-2.62 volts.
If voltage is as specified, reconnect sensor connector and go to step
3). If voltage is not as specified, leave special tool and DVOM
connected and go to next step.
2) Note top center position of sensor, and remove sensor. See
"G" SENSOR under REMOVAL & INSTALLATION . Secure sensor so that arrow
on sensor is facing straight down. Voltage should be 3.4-3.6 volts. If
voltage is specified, reinstall sensor and go to next step. If voltage
is not as specified, replace sensor.
3) Turn ignition off. Disconnect ECU 26-pin connector. Turn
ignition on. Check voltage between ECU 26-pin connector terminals No.
4 and 17. See Figs. 5-6. Voltage should be 2.4-2.6 volts. If voltage
is as specified, go to next step. If voltage is not as specified,
check and repair connectors and related wiring harness between ECU and
sensor. See WIRING DIAGRAMS .
4) Check and repair ECU 26-pin connector. If connector is
okay, replace ECU.
Fig. 10: Locating "G" Sensor
Courtesy of Mitsubishi Motor Sales of America.
DTC 33: STOPLIGHT SWITCH SYSTEM

Fig. 16: Locating Electronic Control Unit (ECU)
Courtesy of Mitsubishi Motor Sales of America.
"G" SENSOR
CAUTION: DO NOT turn "G" sensor upside-down or lay unit on its side.
DO NOT drop "G" sensor. DO NOT disassemble unit. Replace "G"
sensor as an assembly.
Removal & Installation
Sensor is located under center console, near shifter. See
Fig. 10 . Remove center console assembly. Disconnect sensor wiring
harnes s connector. Remove sensor. To install, reverse removal
procedure. Tighten bolts to specification. See TORQUE SPECIFICATIONS.
HYDRAULIC UNIT
Removal
Remove brakelines from hydraulic unit. Remove ABS relay box
cover. See Fig. 3. Disconnect ground wire and wiring harness
connectors from hydraulic unit. Remove hydraulic unit retaining nuts.
Carefully remove hydraulic unit.
Installation
To install, reverse removal procedure. Install hydraulic unit
brakelines. Ensure brakelines are installed in correct location. See
Fig. 17. Bleed brake system. See BLEEDING BRAKE SYSTEM.

AUTO TRANS DIAGNOSIS - R4AW3 & V4AW3
1998 Mitsubishi Montero
1997-98 AUTOMATIC TRANSMISSIONS
Mitsubishi R4AW3 & V4AW3 Electronic Controls
Montero, Montero Sport
APPLICATION
TRANSMISSION APPLICATION








\









\









\









\









\









\









\







Vehicle Transmission Model
Montero Sport 2WD ............................................ R4AW3
Montero & Montero Sport 4WD .................................. V4AW3









\









\









\









\









\









\









\







CAUTION: Vehicle is equipped with Supplemental Restraint System (SRS).
When servicing vehicle, use care to avoid accidental air bag
deployment. SRS-related components are located in steering
column, center console, instrument panel and lower panel on
instrument panel. DO NOT use electrical test equipment on
these circuits. If necessary, deactivate SRS before servicing
components. See AIR BAG SERVICING article in APPLICATIONS &
IDENTIFICATION.
DESCRIPTION
Automatic transmission is a 4-speed electronically controlled
transmission. Solenoids that control shift changes are located in
valve body. Solenoids are controlled by a Transmission Control Module
(TCM). TCM receives information from various input devices and uses
this information to control shift solenoids for transmission shifting
and lock-up solenoid for torque converter lock-up.
An Overdrive (OD) switch is mounted on the shift lever. When
OD switch is depressed to ON position, transmission will shift into
4th gear when shift lever is in "D" position, and OD OFF light on
instrument panel will go off. When OD switch is released to OFF
position, transmission will shift into 3rd gear, and OD OFF light on
instrument panel will illuminate.
A pattern select switch is located near shift lever on center
console. Pattern select switch contains a NORMAL and a HOLD operating
position. When pattern select switch is depressed (HOLD position) with\
shift lever in Drive position, transmission starts in 2nd gear.
Upshifts and downshifts will occur at a higher vehicle speed than with
switch in NORMAL position. See MITSUBISHI R4AW3 & V4AW3 OVERHAUL
article. Indicator light on instrument panel indicates pattern select
switch is in HOLD position.
Transmission is equipped with a shift lock and key interlock
system. Shift lock system prevents shift lever from being moved from
Park unless brake pedal is depressed. Key interlock system prevents
ignition key from being moved from ACC to LOCK position on ignition
switch unless shift lever is in Park. See MITSUBISHI SHIFT LOCK
SYSTEMS article.
OPERATION
TCM
TCM receives information from various input devices and uses

(62-73 kPa) of vacuum applied to the brake booster.
PARKING/EMERGENCY BRAKE
NOTE: Adjust service brakes before adjusting parking brake.
Start engine, and apply brake pedal. Pull parking brake lever
with a force of 44-45 lbs. (196-200 N). Parking brake lever should
move up 3-5 notches on Diamante, Stealth and 3000GT, 4-6 notches on
Montero, and 5-7 notches on all other models. If adjustment is
necessary, turn adjusting nut located under console or at end of cable
rod. See Fig. 6.
Fig. 6: Adjusting Parking/Emergency Brake (Typical)
Courtesy of Mitsubishi Motor Sales of America.
REAR BRAKE SHOES
Fully release parking brake and depress brake pedal several
times to center shoes and adjust brake shoe clearance. Adjust shoes so
brake shoes lightly contact brake drum. Adjust parking brake, and
check pedal travel. Rotate brake drum to verify free movement.
STOPLIGHT SWITCH
Loosen lock nut, and adjust switch-to-pedal arm clearance to
0.02-0.04" (0.5-1.0 mm). Tighten lock nut. DO NOT depress master
cylinder push rod during stoplight switch adjustment.
TESTING

release bearing with solvent. Apply a light coat of multipurpose
grease to release bearing sliding surface. Apply a very light coating
of grease to input shaft splines. DO NOT allow grease or dirt on
clutch disc or pressure plate surfaces.
3) To install remaining components, reverse removal
procedure. Refill all fluids to proper levels. Adjust all control
cables, clutch pedal height and free play. See CLUTCH PEDAL HEIGHT and
CLUTCH PEDAL FREE PLAY under ADJUSTMENTS. See Fig. 1.
Removal (4WD Models)
1) Remove switch panel from rear console. Remove suspension
control switch or hole cover. Disconnect rear console harness
connector. Remove side panel. Remove rear console assembly. Remove
shift lever knob(s). Remove floor console harness connector. Remove
front console assembly.
2) Move transmission lever to Neutral position and transfer
lever to 4H (4WD high range) position. Remove control lever boot
retainer and boot. Remove transmission and transfer control lever
assemblies. Remove control lever bushing (transmission), gaskets and
stopper plates.
3) Raise and support vehicle. Remove skid plate and front
exhaust pipe. Drain transmission and transfer case fluid. Index mark
front and rear drive shaft flanges. Remove front and rear drive
shafts.
4) Remove drive shaft dust seals. Disconnect HI/LO and
2WD/4WD detection switch connectors. Disconnect back-up light switch
connector. Disconnect center differential lock detection switch
connector. Disconnect center differential lock operation switch
connector. Disconnect 4WD operation detection switch.
5) Disconnect speedometer cable. Remove clutch slave cylinder
heat shield. Remove clutch slave cylinder (without disconnecting
hydraulic line) and wire aside. Remove starter and starter cover.
Remove heat shield, both transmission stays and bellhousing lower
cover.
6) Support transmission with transmission jack. Remove
transfer case roll stopper and bracket. Remove crossmember and engine
mounting rear insulator. Remove transfer case protector bracket and
mass damper. Remove remaining bellhousing bolts. Pull toward rear of
vehicle to free transmission input shaft from clutch. Lower
transmission/transfer assembly from vehicle.
7) If reusing pressure plate, mark pressure plate to flywheel
for installation reference. Insert a clutch alignment tool to prevent
pressure plate and clutch disc from dropping. Loosen pressure plate
bolts gradually in a crisscross pattern to avoid warping pressure
plate flange during removal. Remove pressure plate and clutch disc.
See Fig. 3 .
Fig. 3: Removing & Installing Clutch On Flywheel (Typical)
Courtesy of Mitsubishi Motor Sales of America.
Inspection
1) Check release bearing and release fork for damage or wear.

1) Start and run engine at 2000 RPM. Ensure battery is fully
charged. Turn defogger switch to ON position. Using a voltmeter, check
voltage at center section of each defogger grid filament.
2) If voltage is about 6 volts, grid filament is okay. If
voltage is about 12 volts, an open is present in negative circuit.
Move probe slowly toward negative terminal to determine location of
open circuit.
3) If voltage is zero volts, an open is present in positive
circuit. Move probe slowly toward positive terminal to determine
location of open circuit. Repair grid as necessary. See
GRID FILAMENT REPAIR under ON-VEHICLE SERVICE.
ON-VEHICLE SERVICE
GRID FILAMENT REPAIR
Clean broken wire tips thoroughly. Place masking tape along
both sides of broken wire. See Fig. 8. Apply Repair Paste (DuPont
4817) to broken section of grid. Remove masking tape after paste has
dried. Wait 24 hours before using defogger.
Fig. 8: Repairing Rear Defogger Grid Element
REMOVAL & INSTALLATION
DEFOGGER SWITCH
Removal & Installation (Diamante)
Defogger switch is integral with A/C system ECU. To remove
A/C ECU, remove center console. Remove audio panel. Remove radio.
Remove A/C ECU. To install, reverse removal procedure.
Removal & Installation (Eclipse)
Remove upper stoppers from glove compartment. Drop down glove
compartment. From glove compartment opening, reach behind center air
outlet assembly and disconnect harness connectors to switches. Release
metal clips from center air outlet assembly. Remove center air outlet.
Remove defogger switch from center air outlet. To install, reverse
removal procedure.
Removal & Installation (Galant)

At heater unit, remove center air outlet cool air by-pass
lever cable from damper lever. To remove center air outlet, push
springs at bottom of center air outlet upward. Outlet is located above
radio. Remove switch from center air outlet. To install, reverse
removal procedure. Turn cool air by-pass lever on outlet fully upward.
Pull air by-pass lever fully downward and install cool air by-pass
lever cable to damper lever.
Removal & Installation (Mirage)
Remove driver-side lower dash panel. Remove center console
assembly and foot distribution duct. Disconnect rear window defogger
switch harness connector. Remove switch. To install, reverse removal
procedure.
Removal & Installation (Montero)
Remove defogger switch by prying switch off instrument
cluster bezel. Disconnect wiring harness from defogger switch. Remove
switch. To install, reverse removal procedure.
Removal & Installation (Montero Sport)
Remove instrument cluster bezel. Bezel is held in by metal
clips. Disconnect wiring harness from defogger switch. Remove switch
from behind bezel. To install, reverse removal procedure.
Removal & Installation (3000GT)
Remove knee protector. Remove steering column upper and lower
covers. Remove instrument cluster bezel. Disconnect wiring harness
from defogger switch. Remove defogger switch. To install, reverse
removal procedure.
WIRING DIAGRAMS

Connect air pressure gauge in-line to air hose from air pump.
Air pump is located in right storage area, under rear seat. Connect
battery voltage to air pump (positive lead to Red wire). The air pump
is operating correctly when the following sequences occur;
* Pump should operate for no more than 5 seconds.
* Pressure should be 4-6 psi (.28-.41 kg/cm
) within 10-20
seconds after pump has stopped.
* After air pump has stopped operating, it should not restart
operating for 5 minutes.
Center Differential Lock Operation Switch
See ANTI-LOCK BRAKE SYSTEM article in BRAKES.
Differential Lock Switch
Remove switch from center console. To test switch operation,
see Fig. 2 . Replace switch as needed.
Differential Lock Control Unit
See ANTI-LOCK BRAKE SYSTEM article in BRAKES.
Lock Detection Switch
1) Raise and support vehicle. Disconnect air hose connection
near rear differential. Connect air source with pressure regulator and
pressure gauge. Apply 4 psi (.28 kg/cm
) pressure. Disconnect lock
detection switch harness connector.
2) Using ohmmeter, check if continuity exists with air
pressure applied. Continuity should exist with air pressure applied.
If continuity exists, ensure axle is locked by attempting to turn rear
wheels separately of each other.
3) If continuity does not exist, go to step 4). If continuity\
does exist but axles are not locked, see CARRIER ASSEMBLY under
REMOVAL & INSTALLATION and inspect locking assembly.
4) Remove detection switch from housing. Using ohmmeter,
check continuity of switch. Continuity should exist with switch
plunger extended. With plunger in neutral position, continuity should
not exist. Replace switch as needed.
Fig. 2: Checking Differential Lock Switch Continuity
Courtesy of Mitsubishi Motor Sales of America.
REMOVAL & INSTALLATION