Page 191 of 396
REAR AXLE – Special Tools / Troubleshooting 27-5
MB990988NumberNameO.D. mm
1MB990551Box–
2MB990989Base–
3(MB990990)Tool A25
(MB990991)Tool B28
(MB990992)Tool C31
MB990925
Brass bar
Bar (one-touch type)Toolbox
Installer adapter
Tool number (MB990925)O.D. mmTool number (MB990925)O.D. mm
AMB99092639.0AMB99093363.5
MB99092745.0MB99093467.5
MB99092849.5MB99093571.5
MB99092951.0MB99093675.5
MB99093054.0MB99093779.0
MB99093157.0BMB990938–
MB99093261.0CMB990939–
TROUBLESHOOTING
1. BASIC TROUBLESHOOTING CONDITIONS
Before starting the troubleshooting procedure, make sure that the following items have been checked
okay.
The correct steering wheel has been properly installed in the neutral position of the steering column
shaft.
Tire and wheel sizes are correct with correct specifications. Inflation pressure, balance, and wear
conditions are okay.
Wheel alignment is correct.
The engine, suspension, and other parts have not been remodeled so as to affect the AYC system.
2. DIAGNOSIS FUNCTION
READING THE DIAGNOSIS CODE
Read the diagnosis code using AYC warning lamp.
Page 283 of 396
ABS – Troubleshooting35B-4
Code No.15: Wheel speed sensor (abnormal output
signal)Probable cause
This code is output when there is an abnormality in the output signal from any one
of the four wheel speed sensors while driving (except for an open circuit or short
circuit).The four vehicle tires are of different sizes
Malfunction of wheel speed sensor
Malfunction of wiring harness or connector
Malfunction of ABS-ECU
Malfunction of wheel bearing
OK
Check the harness wire, and repair
if necessary.
Between each wheel speed sensor
and ABS-ECU
OK
Wheel bearing checkNG
Replace the ABS-ECU.
OK
ABS rotor checkNG
RepairOK
Check the trouble symptom.
OK
Check the following connector:
B-24NG
Repair
OK
Check the trouble symptom.
OK
Wheel speed sensor output voltage
check (Refer to P.35B-17.)NGWheel speed sensor checkNG
Replace
YES
Wheel speed sensor installation checkNG
Repair
Are the sizes of all four tires identical?NOEquip the vehicle with tires of identical
sizes.
NG
Page 383 of 396
CHASSIS ELECTRICAL – Front Fog Lamp54-39
FRONT FOG LAMP
SERVICE SPECIFICATIONS
ItemsStandard value
Headlamp aiming [Paren-
thesized are allowableVertical direction2° (349 mm) below horizontal line (H)
t
beam axis deviations 10 m
ahead of headlamp.]Horizontal direction3° (524 mm) leftward from vertical line (V)
ON-VEHICLE SERVICE
HEADLAMP AIMING
Bring the vehicle in the following conditions before aiming
the headlamp.
Check the tires for inflation pressure. Pump them up if
necessary to the labeled pressure level.
Set the vehicle unladen on a level floor.
Place one person (approximately 55 kg) on the driver’s
seat.
Maintain an engine speed of 2,000 r/min to keep the
battery in the charged condition.
1. Position the tester so that its converging lens faces the
fog lamp center to center at a distance of 10 m.
NOTE
Measure the center of the fog lamp as shown.
A: 572.5 mm (from the center of the vehicle body)
B: 360 mm
2. Remove the fog lamp bezel, and using the aiming
adjustment screw, aim the fog lamp to the standard value.
NOTE
The horizontal direction is non-adjustable. If the beam
axis deviation exceeds the standard value, check the
fog lamp to determine if it is installed out of position and
correct if necessary.
Face to face 10 m apart from
each other
AAB
Adjusting screw
