1998 Mercury Villager warning

WARNING
You should never place hard items such as coffee mugs or
drinking glasses on the table-top seats when the
vehicle is moving. Any item can become a projectile
inside a vehicle involved in a collision. To help prevent
personal injury, never leave loose items on the fold-down
table-top seats when the vehicle is moving.
Table and built-in cupholders on the fold-down seatback
Adjustable Rear Seating
205

Fuel-Injected Engines
When starting a fuel-injected engine,the most important thing to
remember is to avoid pressing down on the accelerator
before or during starting. Only use the accelerator when you
have problems getting your vehicle started. SeeStarting Your Engine
in this chapter for details about when to use the accelerator
while you start your vehicle.
Starting Your Vehicle
Preparing to Start Your Vehicle
WARNING
Do not start your vehicle in a closed garage or in other
enclosed areas. Exhaust fumes can be toxic. Always open the
garage door before you start the engine.
Before you start your vehicle, always:
1. Make sure you and all your passengers buckle your safety
belts. SeeSafety beltsin the Index for more details.
2. Make sure the headlamps and other accessories are turned off
when starting.
3. Make sure that the gearshift is in P (Park) and the parking
brake is set before you turn the key.
4. Observe the warning lights on the instrument cluster to make
sure they work. Refer to theInstrumentationchapter.
Starting Your Engine
To start your engine:
1. Follow the steps underPreparing to Start Your Vehicleat the
beginning of this section.
Starting
207

NOTE: Your vehicle has an interlock that prevents you from
shifting out of P (Park) unless your foot is on the brake
pedal.
If the engine does not start after two attempts:
1. Turn the ignition key to the OFF position.
2. Press the accelerator all the way to the floor and hold it.
3. Turn the ignition key to the START position.
4. Release the ignition key when the engine starts.
5. Release the accelerator gradually as the engine speeds up.
If the engine still does not start, the fuel pump shut-off switch may
have been activated. For directions on how to reset the switch
seeFuel Pump Shut-Off Switchin the index.
A computer system controls the engine's idle speed. When you
start your vehicle, the engine's idle speed normally runs high.
These faster engine speeds will make your vehicle coast
slightly faster than its normal idle speed. It should, however,
slow down after a short time. If it does not, have the idle speed
checked.
If the engine idle speed does not slow down automatically, do
not allow your vehicle to idle for more than 10 minutes. Have the
vehicle checked.
WARNING
Extended idling at high engine speeds can produce very
high temperatures in the engine and exhaust system,
creating the risk of fire or other damage.
Starting
209

WARNING
Do not park, idle, or drive your vehicle in dry grass or
other dry ground cover. The emission system heats up the
engine compartment and exhaust system, which can
start a fire.
If you consistently start your vehicle in subzero temperatures, use
an engine block heater (if your vehicle has this option). If your
vehicle does not have this option, it is available thru your dealer.
Engine Block Heater (Canada only)
Engine block heaters are strongly recommended if you live in a
region where temperatures reach ±10É F (±23É C) or below. An
engine block heater warms the engine coolant, which improves
starting, warms up the engine faster, and allows the heater-defrost
system to respond more quickly.
WARNING
To prevent electrical shock, do not use your heater with
ungrounded electrical systems or two-pronged (cheater)
adapters.
For best results, plug the heater in at least three hours before you
start your vehicle. Using the heater for longer than three hours
will not damage the engine, so you can leave it plugged in all night
to start your vehicle the following morning.
What To Do If The Engine Does Not Start
Fuel Pump Shut-Off Switch
If the engine cranks but does not start or does not start even after
a small collision, the fuel pump shut-off switch may have been
activated. The shut-off switch is a device intended to stop the fuel
pump when your vehicle has been involved in a substantial
jolt. Refer to theRoadside emergenciessection for more information.
210

Once the shut-off switch is activated, you must reset the switch
by hand before you can start your vehicle.
The fuel pump shut-off switch reset button is located below the
hood release handle.
WARNING
If you see or smell fuel, do not reset the switch or try to
start your vehicle. Have all the passengers get out of the
vehicle and call the local fire department or a towing
service.
If your engine cranks, but does not start after a collision:
1. Turn the key in the ignition to the OFF position.
2. Check under the vehicle for leaking fuel.
3. If you do not see or smell fuel, push the fuel pump shut-off
reset button down. If the red button is already set, you may
have a different mechanical or electrical problem.
4. Turn the ignition key to the ON position for a few seconds,
then turn it to the OFF position.
Fuel pump shut-off switch reset button location
Starting
211

5. Check under the vehicle again for leaking fuel. If you see or
smell fuel, do not start your vehicle again. If there is no
fuel, you can try to start your vehicle again.
6. Check all vehicle warning lights before driving your vehicle.
Guarding Against Exhaust Fumes
Carbon monoxide, although colorless and odorless, is present in
exhaust fumes. Take precautions to avoid its dangerous
effects.
WARNING
Do not start your vehicle in a closed garage or in other
enclosed areas. Exhaust fumes can be toxic. Always open the
garage door before you start the engine.
WARNING
If you ever smell exhaust fumes of any kind inside your
vehicle, have your dealer inspect and fix your vehicle
immediately. Do not drive if you smell exhaust fumes.
These fumes are harmful and could kill you.
Have the exhaust and body ventilation systems checked by a
qualified technician whenever:
myour vehicle is raised for service
mthe sound of the exhaust system changes
myour vehicle has been damaged in an accident
Improve your ventilation by keeping all air intake vents clear of
snow, leaves, and other objects.
If the engine is idling while you are stopped in an open area for
long periods of time, open the windows at least one inch (2.5
cm). Also, adjust the heating or air conditioning system to bring
in outside air.
212

Read the sectionClimate Control Systemsfor instructions on
bringing fresh outside air into your vehicle. Refer to the Index.
Removing the Key From the Ignition
OFF/LOCK is the only position that allows you to remove the
key from the ignition. The LOCK feature helps to protect your
vehicle from theft, because it also locks the steering wheel
and the gearshift lever when the key is removed.
If your key is stuck in the LOCK position, and you are unable to
turn it, move your steering wheel left or right until the key
turns freely in the lock.
To remove your key from the ignition:
1. Put the gearshift lever in P (Park).
2. Set the parking brake fully.
3. Turn the ignition key to LOCK.
4. Remove the key.
WARNING
When you leave your vehicle, place the gearshift lever in
P (Park). Set the parking brake fully, and shut off the
engine. Never park your vehicle in N (Neutral). If you do
not take these precautions, your vehicle may move
suddenly and injure someone.
WARNING
Do not leave children, unreliable adults, or pets
unattended in your vehicle.
Starting
213

During ABS activation, a mechanical noise may be heard as the
ABS cycles. This is normal ABS operation.
Anti-lock brake system (ABS)
On vehicles equipped with an anti-lock braking system (ABS), a
noise from the hydraulic pump motor and pulsation in the
pedal may be observed during ABS braking events. Pedal pulsation
coupled with noise while braking under panic conditions or on
loose gravel, bumps, wet or snowy roads is normal and indicates
proper functioning of the vehicle's anti-lock brake system. If
the vehicle has continuous vibration or shudder while braking,
felt mainly in the steering wheel, the vehicle most likely needs
service.
The ABS system has self-check capabilities. The system turns on
the ABS warning light each time you start the engine. After
the engine is started and the ABS warning light turns off, the system
performs another test the first time the vehicle reaches 4 mph
(6 km/h). A mechanical noise may be heard as the ABS system
performs a self test. This is a normal part of the self test
feature. If a malfunction is found during this check, the ABS
warning light will come on.
You should always be careful when braking, even if your vehicle
has the ABS system. Heavy braking on roads with loose
surfaces such as snow or gravel, or roads with severe pavement
irregularities could also cause you to lose control of your
vehicle.
WARNING
If the anti-lock brake system warning light remains on or
comes on while driving, have the braking system
checked by a qualified service technician as soon as
possible.
216