1998 Mercury Villager ECU

WARNING
Never use wheels or lug nuts different than the original
equipment as this could damage the wheel or mounting
system. This damage could allow the wheels to come
off while the vehicle is being driven.
13. Replace the wheel cover by pressing it into place. If you have
the standard wheel covers, you must align the notch in the
wheel cover with the tire's valve stem and align the recess in the
back of the wheel cover with one of the lug nuts. If you
have the optional aluminum wheel, press the center wheel
cap into place after matching up the design of the wheel cap
to the wheel.
14. Make sure the jack is securely fastened. When you replace
the jack in the jack storage compartment, place the base
against the square-shaped fastening bracket and open the jack
slightly so that the jack is snug against the fastening
brackets.
15. Store the flat tire under the vehicle just as you would store
the spare tire. Refer to the section onStowing the Spare Tire
in this chapter.
266

16. Make sure the lug wrench is secured back into the tool kit and
store it next to the jack.
17. Unblock the wheels.
Retighten the lug nuts to the specified torque at 500 miles (800
km) of operation, after any wheel change, or any time the lug nuts
are loosened.
Storing the jack
Roadside Emergencies
267

If you must work under the hood while the engine is running:
mSet the parking brake fully and make sure that the gearshift
is securely latched in P (Park). This will prevent your
vehicle from moving unexpectedly.
WARNING
Do not start your engine with the air cleaner removed and
do not remove it while the engine is running.
mAvoid wearing loose clothing or jewelry that could get caught
in moving parts. Take appropriate precautions with long hair.
Opening the Hood
1. Pull the hood release handle, located below the fuse panel
door.
Hood release handle location
Maintenance and Care
277

To close the hood:
1. Remove the prop rod from the slotted hole in the hood. Place
the rod in its retaining clip and close the hood with enough
force to make it latch. Be sure to oil the hood latch every six
months to maintain smooth operation.
2. Try to lift the hood after closing it to be sure it is securely
latched.
Engine Oil Recommendations
Ford oil specification is WSS-M2C153-G.
Use SAE 5W-30 motor oil certified for gasoline engines by the
American Petroleum Institute.
Do not use supplemental engine oil additives, oil treatments or
engine treatments. They are unnecessary and could, under certain
conditions, lead to engine damage which is not covered by
your warranty.
Maintenance and Care
279

Checking Engine Oil
Check the engine oil each time you fuel your vehicle.
1. Make sure the vehicle is on level ground.
2. Turn the engine off and wait a few minutes for the oil to drain
into the oil pan.
3. Set the parking brake and ensure the gearshift is securely
latched in Park,9P9.
4. Open the hood. Protect yourself from engine heat.
5. Locate and carefully remove the engine oil level indicator (dip
stick).
6. Wipe the indicator clean. Insert the indicator fully, then
remove it again.
mIf the oil level isbetween the L and H marks,the oil level is
acceptable.DO NOT ADD OIL
mIf the level is below the L mark, add enough oil to raise the
level within the L-H range
WARNING
Oil level above the H mark may cause engine damage.
Some oil must be removed from the engine by a service
technician.
7. Put the indicator back in and ensure it is fully seated.
280

Automatic Transmission Fluid
Under normal circumstances, you do not need to check the fluid
level of the transaxle since your vehicle does not use up
transmission fluid. However, if the transaxle is not working
properly (for example, slipping or shifting slowly), or you notice
some sign of fluid leakage, the fluid level should be checked.
It is best to check the transmission fluid level at normal operating
temperature, after approximately 20 miles (30 km) of driving.
However, if necessary, you can check the fluid level without having
to drive 20 miles (30 km) to obtain a normal operating
temperature if outside temperatures are above 50É F (10É C).
NOTE: If the vehicle has been operated for an extended period
at high speeds or in city traffic during hot weather, or
if it has been pulling a trailer, the engine should be
turned off for about 30 minutes to allow the fluid to
cool before checking.
Checking the Automatic Transmission Fluid
With the vehicle on a level surface, start the engine and move the
gearshift lever through all of the gear ranges allowing
sufficient time for each position to engage. Securely latch the
gearshift lever in the P (Park) position, fully set the parking brake
and leave the engine running.
Wipe off the dipstick cap, pull the dipstick out and wipe the
indicator end clean. Put the dipstick back into the filler tube and
make sure it is fully seated. Pull the dipstick out and read the
fluid level.
Maintenance and Care
291

WARNING
The temperature grade for this tire is established for a tire
that is properly inflated and not overloaded. Excessive
speed, underinflation, or excessive loading, either
separately or in combination, can cause heat buidlup and
possible tire failure.
The information on braking performance and tire quality grading
found in the ªFord Motor Company Passenger Car Consumer
Informationº pamphlet (FPS 12024-92) also applies to the Villager.
This publication is available from your dealer.
Snow Tires and Cables
The tires on your vehicle have all-weather treads that provide
traction in rain or snow. However, during the winter months in
some climates, you may need to use snow tires and
occasionally cables for your tires.
WARNING
When using snow tires, make sure they are the same size
and grade as the tires you normally use on your
vehicle.
Do not use cables when using a temporary spare. For full size
tires, use cables on the tires only in an emergency or if the law
requires them where you drive. When you use the tire cables:
mMake sure the cables are the right size for your tires. Use only
SAE Class ªSº cables. Other types may damage your vehicle.
mPut cables on tightly with the ends held down securely. Follow
the cable manufacturer's instructions.
Maintenance and Care
305

Safety Equipment
Vehicle Security Systems
Travel Equipment
Aero Hood Deflector
Bike Rack Adaptor (Attaches to Base Roof Rack)
Four Season Base Roof Rack
Multi Sport Removable Rack
Multi Sport Bike Adaptor
Multi Sport Ski/Snowboard Adaptor
Multi Sport Water Sport Adaptor
Ski Rack Adaptor (Attaches to Base Roof Rack)
NOTE: When adding accessories, equipment, passengers, and
luggage to your vehicle, do not exceed the total weight
capacity of the vehicle or of the front or rear axle
(GVWR, GAWR as shown on the Safety Compliance
Certification Label). Consult your dealer for specific
weight information.
NOTE: Devices that emit radio frequency (RF) energy such as
AM/FM radios, mobile communication systems
(two-way radios, telephones) and radio controlled
security systems, are subject to the rules and regulations
of the Federal Communications Commission (FCC) 47
CFR Parts 2 and 15. Any such system installed in your
vehicle should comply with those rules and should
be installed only by a qualified technician. In addition,
to insure continued compliance with the FCC's
requirements, RF devices must not be modified or
changed in a manner not expressly approved by Ford
Motor Company.
Accessories
357