1998 Mercury Villager light

How to Take Care of and Clean Your CD Changer and
Discs
To ensure the continued performance of your Ford Compact Disc
Changer, carefully read the following precautions:
mAlways handle the disc by its edge. Never touch the playing
surface.
mBefore playing, inspect the disc for any contamination. If
needed, clean the disc with an approved disc cleaner, such as the
DiscwashertCompact Disc Cleaner or the Allsop 3t
Compact Disc Cleaner, by wiping from the center out to the
edges.Do not use a circular motion to clean.
mDo not clean discs with solvents such as benzene, thinner,
commercially available cleaners or antistatic spray
intended for analog records.
mDo not expose the disc to direct sunlight or heat sources such
as defroster and floor heating ducts. Do not leave any discs in
a parked car in direct sunlight where there may be a
considerable rise in temperature or damage may result.
mAfter playing, store the disc in its case.
mIf a disc has already been inserted, do not try to insert another
disc. Doing so may damage the disc changer.
mDo not insert anything other than a disc into the disc changer.
WARNING
The laser beam used in the compact disc player is harmful
to the eyes. Do not attempt to disassemble the case.
Electronic Sound Systems
45

If there is a building or large structure between the antenna and
station, some of the signal ªbendsº around the building, but
certain spots receive almost no signal. Moving out of the ªshadowº
of the structure will allow the station to return to normal.
This condition exists when the radio waves are reflected off objects
or structures; the reflected signal cancels the normal signal,
causing the antenna to pick up noise and distortion. Cancellation
effects are most prominent in metropolitan areas, but also can
becomes quite severe in hilly terrain and depressed roadways.
To minimize the effects of these conditions, a stereo/mono blend
circuit has been incorporated into this system. This feature
automatically switches a weak stereo signal to a clearer monaural
signal, which improves the quality of reception.
Several sources of static are normal conditions on AM
frequencies. These can be caused by power lines, electric fences,
traffic lights and thunderstorms.
Another reception phenomenon isStrong Signal Capture and
Overload. This can occur when listening to a weak station and
when passing another broadcast tower. The close station may
capture the more distant station, although the displayed frequency
does not change. While passing the tower, the station may
switch back and forth a few times before returning to the original
station.
When several broadcast towers are present (common in
metropolitan areas), several stations may overload the receiver,
resulting in considerable station changing, mixing and distortion.
Automatic gain control circuitry for both AM and FM bands
has been incorporated into this system to reduce strong signal
capture and overload.
50

The controls for the climate control systems, headlamps, clock,
radio, rear window washer and wiper, hazard flasher, power mirror
controls, and speed control are all on the instrument panel.
Climate Control Systems
Function Selector Buttons
There are six function selector buttons: OFF, Mix, Defrost, Panel,
Panel/Floor, and Floor. When you press a function selector
button, the indicator light on the button will illuminate. If your
vehicle is equipped with a rear passenger compartment climate
control system, the instrument panel will also include a rear
seat function selector.
mThe OFF button shuts off the air supply to all outlets and
stops all fan operations. Use this setting when driving through
an area where outside air is unpleasant or dusty.
Climate control system panel
56

WARNING
Operating with the function selector control in off or in
the recirculated air mode for extended periods of time in
cold weather can result in fog buildup on interior glass
surfaces.
mThe Mix () button directs approximately equal amounts
of air to the windshield and floor outlets with a small
amount to the side windows.
mThe Defrost (
) button directs air to the windshield and
front side windows with a small amount going to the floor
outlets.
mThe Panel (
) button directs air to the instrument panel
outlets.
mThe Panel/Floor (
) button directs approximately equal
amounts of air to the instrument panel outlets and the floor
outlets.
mThe Floor (
) button directs most of the system's air
supply to the floor outlets with a small amount going to the
windshield and side window defrosters.
Air Outlets
Air intake selector button
The typical air intake selection is outside air. However, for
recirculated air, the air intake selector button may be activated.
When the air intake selector button is activated (indicator light is
on), it prevents the intake of outside air. This is the typical
selection when using the air conditioner (if equipped). It
recirculates interior air for faster cooling. The recirculated air
function also helps to prevent the intake of dusty or unpleasant air.
Controls and Features
57

There are several air outlets on the instrument panel. There are
side outlets near the driver's window and passenger's window, two
center outlets, floor outlets, and windshield outlets. The
direction and amount of air flow from the center and side
instrument panel outlets can be adjusted for personal comfort.
NOTE: Selection of the recirculated air mode under cold and
humid conditions may result in window fogging due to
entrapped humidity within the vehicle. To counteract
this circumstance, switch to the Defrost mode and set fan
speed to 3 or 4. Adjust air temperature to a ªwarmº
instead of ªhotº setting and deactivate the air intake
selector.
Heating Only System (Without air conditioning)
You can heat and ventilate the inside of your vehicle, or defrost
the windshield with the function selector buttons, the fan speed
knob and the temperature control knob.
An additional push-on/push-off air intake selector button
provides for the selection of recirculated inside air (button lighted)
or outside air (button not lighted).
58

Turning on the air conditioner
To cool your vehicle quickly in warm weather:
1. Press one of the function selector buttons (typically Panel, but
Panel/Floor, Floor or Mix can be selected).
2. Turn the temperature control knob to COOL.
3. Press the A/C button. The indicator light on the A/C button
will illuminate.
4. The air intake selector button may be in the outside air mode
or the recirculated air mode. The outside air mode is
recommended for best A/C performance when the vehicle
interior is very warm. As interior air comfort is reached, you
may decide to switch to the recirculated air mode.
5. Turn the fan speed knob to the position of your choice.
6. If your vehicle is equipped with the rear passenger compartment
air conditioning unit, it will be on when the front A/C is on
and the rear climate control lever is set to REAR, 1, 2, 3, or 4.
Refer to the previous section for an explanation of the
heating system.
7. Adjust your instrument panel registers.
8. If the inside of your vehicle is very warm, you may want to
drive for a few minutes with the windows down and the air
conditioner on. This forces most of the hot, stale air out of the
vehicle and allows the air conditioner to cool down the
interior more quickly.
The air conditioner may be used to cool the outside air being
drawn into your vehicle, but using recirculated air is more
economical and cools your vehicle more quickly.
Controls and Features
63

NOTE: The A/C button independently toggles the A/C system's
compressor signal and indicator light ON and OFF in
the Panel, Panel/Floor, Floor, Defrost and Mix functions.
The A/C button will not operate or light when the
system is set in the OFF position. The A/C button will
operate in defrost but will not override previously
discussed automatic operation.
Cooling your vehicle with outside air
Cooling your vehicle with air conditioned outside air is quieter
but less economical than using recirculated air. It also has less
cooling capacity.
To cool your vehicle using outside air:
1. Turn the air intake selector button off (the outside air
position). The air conditioning unit directs outside air through
the instrument panel registers.
2. Press one of the function selector buttons.
3. Press the A/C button. The indicator light on the A/C button
will illuminate.
4. Turn the temperature control knob to COOL.
5. Turn the fan speed knob to the position of your choice.
6. Make sure the registers in the instrument panel are open.
During periods of high humidity, vapor may be emitted from the
air outlets when using the A/C with outside air. Correct this
by switching to recirculated air with the A/C button.
64

Changing the Display Mode (English/Metric)
To switch between the English and Metric display mode, press
the DEFROST and A/C buttons simultaneously while rotating the
fan speed dial upward until it stops moving. After one second,
the display will begin to toggle between English and Metric.
Fan Speed and Thumbwheel
The ATC automatically adjusts the fan speed to the existing
conditions. To control the fan speed yourself, use the thumbwheel
located at the extreme right side of the ATC control panel.
Using the thumbwheel cancels the automatic fan speed control,
and causes a
to appear in the display window. Rotate the
thumbwheel up for HI speeds and down for LO speeds.
To return to automatic fan control, press the AUTOMATIC button.
Airflow Function Selector Buttons
Your ATC has five buttons which allow you to make special
selections for airflow. The buttons are grouped in the middle of
the ATC panel and allow you to determine airflow location.
Pressing any of the function selector buttons illuminates the
button pushed and directs airflow to the appropriate location. The
temperature of the airflow will still be automatically controlled.
Return to fully automatic operation by pushing the AUTOMATIC
button.
Push this button for airflow to the floor and windshield at the
same time. The
indicator light illuminates, and the display
window shows the set temperature. However, the air is not
cooled below the temperature outside of the vehicle regardless of
the temperature setting unless the A/C button is pushed.
Controls and Features
71