1998 Mercury Villager door lock

Combination Lap and Shoulder Belts
While your vehicle is in motion, the combination lap and
shoulder belt adjusts to your movement. However, if you brake
hard, turn hard, or if your vehicle receives an impact of 5 mph (8
km/h) or more, the lap and shoulder belt locks and helps to
reduce your forward movement.
After you get into your vehicle, close the door and lock it. Then
adjust the seat to the position that suits you best.
To fasten the belt, pull the combination lap and shoulder belt
from the retractor so that the shoulder portion of the belt crosses
your shoulder and chest. Be sure the belt is not twisted. If it
is, remove the twist. Insert the belt tongue into the proper buckle
until you hear a snap and feel it latch. Make sure the tongue
is securely fastened to the buckle by pulling on tongue.
NOTE: Be sure to read and understandImportant Safety Belt
Informationat the beginning of this chapter.
Fastening the front seat combination lap and shoulder belt
Seating and Safety Restraints
131

Using the Automatic Locking Mode Retractor to Secure
a Child Safety Seat
Your vehicle is equipped with a dual locking mode retractor on
the shoulder belt portion of the combination lap/shoulder safety
belt for the front passenger seat and rear outer seats. The
automatic locking modemust be usedwhen installing a child
seat or infant carrier in the front passenger seat or rear outer seats.
To install a child safety seat or infant carrier, follow these steps:
1. Position the child seat or infant carrier in the vehicle seat. If you
are using the moveable third row seat in the third row
position, the passenger side second row bucket seat, or the
front passenger seat, slide the seat to the rearmost position.
2. Follow the child seat or infant carrier manufacturer's
instructions. Route the safety belt through the child seat or
infant carrier and insert the safety belt tongue into the buckle
until you hear and feel the latch engage. Be sure to follow
the child safety seat manufacturer's instructions for belt
routing. When using the seating position near the sliding door
on the two-passenger bench seat, be sure that the single
window tongue is attached to the auxillary buckle on the side
of the seat.
156

Installing the Two-Passenger Bench Seat
To replace the bench seat in its original position:
1. Make sure the area around the floor anchor positions is free
from obstruction.
2. With the seatback folded down, two people should lift the seat
into the vehicle.
3. Place the seat slightly behind the floor anchor positions and
catch the rear leg anchors into each anchor position.
4. Press down on the front of the seat to secure the front legs to
the two floor latch locks. Place the seatback in the upright
position.
5. Try to move the seat to be sure that it is securely fastened.
6. Always reattach the tongue into the auxiliary buckle mounted
to the sliding door side of the seat.
Labels have been provided on the side of the seat to remind you
of important safety precautions.
7. Replace any floor mats that were removed.
WARNING
Keep foreign objects out of the floor anchors. Objects in
the floor anchors could prevent front and rear seat legs from
engaging properly.
WARNING
Before sitting in the removable seats, make sure that the
seat legs are securely attached by the floor anchors.
186

WARNING
To prevent the vehicle from moving when you change a
tire, be sure the parking brake is set, then block (in both
directions) the wheel that is diagonally opposite (other
side and end of the vehicle) to the tire being changed.
WARNING
If the vehicle slips off the jack, you or someone else could
be seriously injured.
2. Remove the spare tire and jack. See previous section for
instructions on spare tire removal. The jack is located in the rear
storage compartment in the right door panel of the cargo
area. You will have to unfasten the jack before removing it as
shown in the illustration. The jack handle is in the tool kit
located behind the jack.
NOTE: All occupants should be out of the vehicle while it is
on the jack.
Roadside Emergencies
259

mDrive slowly. If you can hear the cables rub or bang against
your vehicle, stop the vehicle and tighten the cables. If you
continue to hear the cables rub or bang against your vehicle,
remove the cables to prevent damage to your vehicle.
mAvoid fully loading your vehicle if possible.
mRemove tire cables at the first opportunity after using them on
snow and ice. Do not use the cables on dry roads.
Make sure your suspension insulators and bumpers are not
missing or worn to avoid damage to your vehicle.
Filling the Fuel Tank
Removing the tethered fuel filler cap
1. Open the fuel door on the driver's side of the vehicle.
2. Slowly unscrew the cap counterclockwise, using caution to
minimize the possibility of fuel spraying.
If the Service Engine Soon warning light comes on and stays
on when you start the engine, the fuel cap may not be properly
seated. Turn off the engine, remove the fuel cap and replace it, being
careful to align the cap properly.
The tethered fuel filler cap
306

Before you fill your vehicle with fuel, extinguish all lit cigarettes,
other smoking materials, and any open flames.
To fill the tank properly:
1. Remove the fuel filler cap. Proceed to add fuel to the tank
only if your vehicle is on level ground.
2. Make sure you pump unleaded fuel and put the nozzle all the
way inside the fuel filler pipe. The fuel tank is normally full
after three automatic shutoffs of the nozzle.
3. If you spill any fuel on the body of your vehicle, clean it off
immediately. The fuel may dull or soften the paint if you do
not wash it off.
4. Replace the fuel cap tightly when you are finished. Turn it
clockwise until you hear at least three clicks. The
ratcheting mechanism allows the fuel cap to be sealed without
overtightening.
5. Push the fuel door closed.
Choosing the Right Fuel
Use only UNLEADED FUEL. The use of leaded fuel is prohibited
by law and could damage your vehicle. The damage may not
be covered by your warranty.
Your vehicle was not designed to use fuel containing
manganese-based additives such as MMT. Additionally, vehicles
certified to California emission standards (indicated on the
underhood Vehicle Emissions Control Information label) are
designed to operate on California reformulated gasolines. If
California reformulated gasoline is not available when you refuel,
your vehicle can be operated on non-California fuels. However,
even though your engine will perform adequately on other
308

Safety, Comfort, and Convenience
Comfort and Convenience
Air Conditioning
Engine Block Heater
Remote Keyless Entry
Protection and Appearance Equipment
Aero Running Boards
Carpeted Floor Mats
Door Edge Guards
Cleaners, Waxes and Polishes
Front End Cover
Front End Mini Cover
Lubricants and Oils
Molded Running Boards
Rear Air Deflector
Side Window Shields
Soft Luggage Cover
Styled Wheel Protector Locks
Super Seal Fabric Protector (U.S. Only)
Super Seal Rustproofing (U.S. Only)
Super Seal Undercoating (U.S. Only)
Touch-Up Paints
Flat Splash Guards
356

Mileage, calculating fuel economy..............311
Mirrors...........................109
automatic dimming rearview mirror...........100
dual electric remote control................110
rearview.........................109
side view mirrors....................109
side view mirrors (manual)................109
side view mirrors (power)................110
Motorcraft parts......................337
O
Octane rating.....................308, 309
Odometer..........................20
description........................20
trip odometer.......................20
Oil filter..........................281
Oil (see Engine oil).....................279
Oil viscosity........................279
Overdrive..........................223
Overseas offices.......................353
P
Parking brake
operation........................218
warning light........................9
Parts (see Motorcraft Parts).................337
PCV valve, specifications..................337
Power door locks......................101
Power features
door locks........................101
mirrors.......................109, 110
windows.........................106
Power steering
dipstick.........................289
Index
385