1998 Mercury Villager headlamp

Turn Signal Lever
You can use the turn signal lever on the left side of the steering
column to:
moperate the turn signals.
mturn the headlamps to high beam.
mflash the headlamps.
mturn the windshield wipers and washer on/off.
Turn Signals
Move the lever up to signal a right turn. Move it down to signal
a left turn. The corresponding indicator light in the
instrument cluster will flash.
If the turn signal stays on after you turn, move the lever back
to the center (off) position.
For lane changes, move the lever far enough to signal but not to
latch. The lever will return to the off position when you
release it.
If the turn indicator light in the instrument panel does not
illuminate or remains on (does not flash) when you signal a turn,
the turn signaling system needs service. Have this condition
corrected as soon as possible, and use the accepted hand signals
until the turn signal system is repaired.
The turn signal lever
Controls and Features
87

Cornering Lights
Your vehicle is equipped with special cornering lights designed
to provide additional illumination toward the direction you are
turning. The corresponding light comes on when a turn is
signaled. The headlamp control must be on in order to activate
the cornering lights.
High Beams and Flashing the Lamps
To turn on the high beams, turn the headlamps on and push the
turn signal lever away from you until it latches. When the
high beams are on, the high beam indicator light on the instrument
panel is illuminated.
To return to the low beam setting, pull the turn signal lever
toward you until it latches back into the neutral position. The high
beam indicator light turns off.
To flash the headlamps, pull the turn signal lever toward you
for a moment and then release it. The high beam headlamps will
flash whether the headlamps are on or off.
High beam and flash-to-pass operation
88

Using the Panic Alarm
If you are near your vehicle and feel threatened, you may
activate the alarm to call attention to it.
To activate the PANIC alarm, push and hold the PANIC button
on the remote for longer than 1.5 seconds. The horn will sound and
the headlamps and tail lights will flash for thirty (30) seconds.
To turn off the alarm, press the LOCK or UNLOCK buttons or hold
the PANIC button down for longer than 1.5 seconds.
Replacing the Batteries
The remote entry transmitter is powered by two coin type Sanyo
CR2016 3 volt batteries (included). If you notice a significant
decrease in operating range, the batteries should be replaced.
Replacement batteries can be purchased at most pharmacies, watch
stores or at your Ford or Lincoln-Mercury dealer.
NOTE: The operating range of the remote entry system can
also be affected by weather conditions (such as very
cold temperatures) or structures around the vehicle
(buildings, other vehicles, radio and TV towers,
etc.). Typical operating range will allow you to be up to
49 feet (15 meters) away from your vehicle.
Replacing the batteries
11 4

ID Code Programming Procedure
NOTE: All transmitters must be programmed (or
reprogrammed) at the same time. If the programming
mode is entered and the transmitters are not programmed
(or reprogrammed) at the same time, they will not
operate with the system.
1. Enter vehicle and close and lock all doors.
2. Insert and remove key from ignition six times within ten (10)
seconds. The instrument panel lights will flash twice.
3. Turn ignition key to the ACC position.
4. Press the LOCK button on the remote transmitter once.
5. To enter additional remote controllers (including the original),
unlock, then lock the driver door using the power door lock
switch.
6. Press the LOCK button on a new remote transmitter. The
instrument panel lights will flash twice, indicating code is
entered.
7. Repeat steps 5 and 6 as needed (up to four remote transmitters
may be programmed).
Anti-Theft System (If equipped)
This system helps protect your vehicle against break-ins or theft
by monitoring all doors, the hood and the liftgate lock
cylinder.
When an unauthorized entry occurs, the system triggers and will:
mflash the headlamps and hazard lamps
mhonk the horn
mdisable the starting circuit to prevent the vehicle from being
started
11 6

Fuel-Injected Engines
When starting a fuel-injected engine,the most important thing to
remember is to avoid pressing down on the accelerator
before or during starting. Only use the accelerator when you
have problems getting your vehicle started. SeeStarting Your Engine
in this chapter for details about when to use the accelerator
while you start your vehicle.
Starting Your Vehicle
Preparing to Start Your Vehicle
WARNING
Do not start your vehicle in a closed garage or in other
enclosed areas. Exhaust fumes can be toxic. Always open the
garage door before you start the engine.
Before you start your vehicle, always:
1. Make sure you and all your passengers buckle your safety
belts. SeeSafety beltsin the Index for more details.
2. Make sure the headlamps and other accessories are turned off
when starting.
3. Make sure that the gearshift is in P (Park) and the parking
brake is set before you turn the key.
4. Observe the warning lights on the instrument cluster to make
sure they work. Refer to theInstrumentationchapter.
Starting Your Engine
To start your engine:
1. Follow the steps underPreparing to Start Your Vehicleat the
beginning of this section.
Starting
207

Lights and Bulb Replacement
It is a good idea to check the operation of the following lights
frequently:
mheadlamps
mhigh-mount brakelamp
mtail lamps
mbrakelamps
mcornering lamps
mhazard flasher
mturn signals
mlicense plate lamps
The alignment of your headlamps should be checked if:
moncoming motorists frequently signal you to turn off your
vehicle's high beams when you do not have the high
beams on
mthe headlamps do not seem to give you enough light to see
clearly at night
mthe headlamp beams are not pointed slightly down and to the
right
Headlamp Bulb
The headlamps on your vehicle use replaceable bulbs. When the
lamp burns out, simply replace the bulb, rather than the
whole lamp.
316

WARNING
Handle a halogen headlamp bulb carefully and keep out
of children's reach. Grasp the bulb only by its plastic
base and do not touch the glass. The oil from your hand
could cause the bulb to break the next time the headlamps
are operated.
Do not remove the burned out bulb unless you can immediately
replace it with a new one. If a bulb is removed for an
extended period of time, contaminants may enter the headlamp
and affect its performance.
Removing the headlamp bulb
1. Make sure that the engine is off and the headlamp switch on
the instrument panel is in the OFF position.
2. Remove the electrical connector from the bulb by pulling the
connector away from the bulb assembly.
The headlamp bulb assembly
Maintenance and Care
317

3. Remove the bulb retaining ring by turning it counterclockwise
1/8 of a turn to free it from the socket. Then slide the ring off
the plastic base.Keep the ring.You must use it again to
hold the new bulb in place.
4. Carefully remove the bulb assembly from its socket by
gently pulling it rearward without turning.
5. Do not touch the bulb with your skin or you could shatter the
bulb. Always grasp the bulb assembly from the plastic base.
6. Be sure that you have the proper replacement bulb ready before
you discard the burned out bulb.
Removing the headlamp bulb retaining ring
318