1998 HONDA INTEGRA battery

Troubleshooting
DTG 54: Fail-safe Relay (cont'd)
MODULATOB UN]T CONI{ESTOR
sor5NorD f;Fl-'Ti)
rBRN/BLn 1qll9l-1i
l-\!xtz)
O)
Y
Terminal side of female terminals
ll
ABS CONTROL UNIT 22P CONITECTOR
Wire side ol female terminals
FAIL.SAFE RELAY CONI{ECTOR
Wire side of temale terminals
ABS CONTROL U[{IT 22P OONNECTOR
{From page'19-57)
Ch6ck tor a shon to powor in thesolenoid powgr source circuit:1. Remove the iumper wire fromthe fail-sale relay connector.2. Measure the voltage betweenthe mod{rlator unit connectortorminal No. 10 and bodyground.
Repair shon to powor in tho wire
between tho ftil{at rolaY, mod-uletor unit and tho undar-hoodABS fu3e/relay box.
ls there battery vokage?
Check tor a $hort to Power in theFSR circuh:1. Disconnect the ABS controlunit 22P connector.2. Turn the ignition switch ON (ll).
3. Measure the voltage betweenthe terminal No.21 and bodyground.
Repair short to powor in tha wircbetwoon the ABS control unit
rnd tho tail{sla rehy.ls there battery voltage?
Chgck for a 3hort to body ground
in th6 FSR circuit:Check for continuiw between theABS control unit 22P connectorterminal No. 21 and body ground.
Rapair short to bodv ground inthe wir. betwoon the ABS con-trol unit andthe f.il-sdo rolay.
Check for an open in the FSRGND circuit:Check lor continuity betlveen thefail safe relay connector terminalNo. 4 and body ground.
Repeir op.n in ths wire betweentho tail-sate.olay and bodyground.
Check for sn opan in the FSR cir-cuh:1. Installthe lail-sale relay.2. Check for continuity betweenthe ABS control unit 22P connector terminal No, 21 andbody ground.
Repair opgn in the wire betwoonthe ABS control unit snd tho fail-safe r6lay.ls there continuity?
lf the probl6m occurs.gain,roolaco the ABS control unit.
Wire side of female terminals

Doors
Glass/Regulator/Glass Run Channel Replacement (cont'd)
9. Remove the power window motor from the
regulator.
NOTE: Before removing the power window motor,
mark the location by scribing a line across the sec
tor gear and regulator.
V: Bolt locations, 3
Qp o"r.o--
El 7Nm(0.7ksf m.
Fl 5 lbf ftls?/:,/
Detach the clips, then peel and remove the glass run
cnanner.
> : Clip locations, 3
10.
GLASS STOPPER
FRONT CHANNEL
CENTEB CHANNEL
20-12
11.
NOTEr lf necessary, remove the glass stopper.
When installing the glass stopper, align it with the notch
in the outer weatherstrip.
Grease allthe sliding surlaces of the regulator where
shown. Install the power window motor on the
regulator.
Check that the regulator moves smoothly by con
necting a 12 V battery to the power window motor
(see section 23).
d
S*--.--;HERwrNDow
-Rt-/'
REGULATOR

>: Bolt locations
l>A.4 >8.2
d|63il;o,ilIu'- *,@
i6pl-".
- 6rbr.ftr _!
7. Disconnect the connector, and remove the regula'
tor through the cenler hole in the door.
NOTE: Scribe a line around the roller guide bolts to
show the original adlustment-
8. Remove the power window motor from the
regulator.
NOTE: Before removing the power window motor,
mark the location by scribing a line across the sec-
tor gear and regulator.
V: Bolt locations, 3
POWERwlNDowMOTOR
CONNECTOR
REGULATOR
9. Grease all the sliding surlaces of the regulator and
center glass guide where shown.
10. lnstall the power window motor on the regulator.
'l 1. Check that the regulator moves smoothly by con
necting a I2 V battery to the power window motor
(see section 23).
V: Adjusting bolt Ilocations,2 \l
\
\L
I ''II
A---- |
\H./ NOTE: Use liqurd@ thread lock.
fFtSlL!=-2
t
ICENTERGLASSGUIDE
MOTOR
(cont dI
20-37

Moonroof
Troubleshooting
SymptomP.obable Cause
Clogged drain tube.
Gap between glass weatherstrip and roof panel
De{ectrve or improperly Installed glass weatherstrip
Gap between drain seal and rool panel.
Excessive clearance between glass weatherstrip and roof panel-
Loose motor.
Worn gear or bearing.
Cable assemblv deformed.
1
2
3
4
1
2
3
1.
Water leaks
Wind noise
Motor noise
Glass does not move, but motor
turns
Clutch out ol adiustment.
Foreign matter stuck between guide rail and slider'
lnner cable loose.
Cable assembly not attached properly
,l
2
3
4
Glass does not move and motor
does not turn (glass can be moved
with moonroof wrench)
1. Blown fuse.
2. Faulty switch.
3. Battery run down.
4. Delective motor.
5. Faulty relay.
Glass Height Adiustment
The roof panel should be even with the glass weather-
srrip, to within 1.8 t O.5 mm {O.07 t 0.02 in} all the
way around. lf not, slide the sunshade back, and:
1. Tilt-up the glass.
2. Loosen the bolts and adjust the glass.
3. Repeat on opposite side if necessary.
1.8 i 0.5 mm 10.07 i 0.02 inl
V : Boll locations, 6
]-
ROOF PANELGLASS BRACKET
Side-to-side iit of glass weatherstrip can be adJust-
ed by loosening the frame mounting bolts and mov-
ing the frame right or left and {orward or backward
by hand (see page 2O-8Oi.
GLASS BRACKETGLASS WEATHERSTRIP
{
$
I
!
20-78

)
Troubleshooting
Glass Height Adjustment
The rooJ panel should be even with the glass weather
strip, to within 1.8 t 0.5 mm (O.O7 tO.O2 in) allthe way
around. It not, slide the sunshade back, and:
1. Tilt-up the glass.
2. Loosen the bolts and adjust the glass.
3. Repeat on opposite side if necessary.
1.810.5 mm {0.07 } 0.02 inl
Gr_ASS
4-(.'
ROOF PANELGLASS BRACKET
GLASS WEATHERSTRIP
4. Side-to-side fit oI glass weatherstrip can be adjust-
ed by loosening the frame mounting bolts and mov
ing the frame right or left and forward or backward
by hand (see page 20-87).
GLASS BRACKET
SymptomProbable Cause
Water leaks1. Clogged drain tube.
2. Gap between glass weatherstrip and roof panel.
3. Detective or improperly installed glass weatherstrip.
4. Gap between drain seal and roof panel.
Wind noise1. Excessive clearance between qlass weatherstriD and roof oanel.
Motor noiseI
2
3
Loose motor.
Worn gear or bearing.
Cable assembly deformed.
Glass does not move, but motor
turnS
1
2
3
Clutch out of adjustment.
Foreign matter stuck between guide rail and slider.
lnner cable loose.
Cable assembly not attached properly.
Glass does not move and motor
does not turn (glass can be moved
with moonroof wrench)
I
2
3
Blown fuse.
Faulty switch.
Battery run down.
Defective motor.
Faulty relay.5
{
s
I
20-85

Dashboard
Component Removal/lnstallation (cont'dl
5. Remove the knee bolster.


: Bolt
A'ir
locations,3
6 x 1.0 mm9.8 N.m
{1.0 kgt m,7.2 tbf.fit
0
6. lnstallation is the reverse o{ the removal procedure.
Ste.eo ladio/cassette, Heatet contlol Danel removal:
1. Remove the rear console, then remove the front
console (see page 20-130).
Loosen the bolts, then remove the stereo radio/
cassette by pulling it out.
Disconnect the connector and antenna lead.
NOTEr The original radio has a coded theft protec-
tion circuit. Be sure to get the customer's code num-
ber before- disconnecting the battery.- removing the No. 47 (7.5 A) tuse from the under-
hood fuse/relay box.- removing the radio,
After service, reconnect power to the radio and turn
it on. When the word "CODE" is displayed, enter
the customer's 5-digit code to restore radio
ope.ation.
KNEE BOLSTER
20-134
CONNECTOR
CASSETTE


: Bolt locations, 2
6x1.0mm9.8 N.m {1.0 kgt m,
3. Carefully pry the hazard warning switch and rear
window detogger switch out of the heater control
panel.
Disconnect the connectors.
HAZARD WARNINGswtTcHREAR WINDOWDEFOGGER SWITCH
CONNECTORS

Dashboard
Replacement Precautions
SRS wire harnesses are routed near the dashboard and
steenng column.
CAUTION:
a All SRS wire hsrnesses are covered wiih yellow insu-
lation. Before you disconnect any pan of an SRS wire
harness, disconnect the airbag conneclors.
a Whenever the ignition switch is ON (ll), or has been
tulned OFF for less than three minules, be careful not
to bump the SRS unit; the ai.bags could accidentally
deploy and cause damage or injuries.
a For additional precautions, refer lo the SRS sub-section
in section 23.
PASSENGER'S AIRBAG
Belore removing the dashboard:
1. Disconnect the battery negative cable, then discon-ne.r rhe n^.iriua.ahla
NOTEr The original radio has a coded thett protec,
tion circuit. Be sure to get the customer's code num
ber before- disconnecting the battery.- removing the No. 47 (7.5 A) fuse from the under-
hood tuse/relay box.- removing the radio.
After service, reconnect power to the radio and turn
it on. When the word "CODE" is displayed, enter
the customer's 5-digit code to restore radio
operation.
DRIVER'S AIRBAG
SRS UNIT
20-138
2.Install the short connectors (RED).
Driver's:
Remove the access panel, then disconnect the con-
nector between the cable reel and driver's airbag.
CABL€ REELCONNECTOR--_--._-_-----
Front passenger's:
Remove the glove box (see page 20-137), thendisconnect the connector between the front pas-
senger's airbag and SRS main harness.
FRONT PASSENGER'SAIRBAG CONNECTOR
SRS MAIN HARNESSCONNECTOR
ORIVER'S AIRBAG

Blower Motor
View from wire side
View from wire slde
BLOWER MOTOR RELAY IP SOCKET
Blower motoa does not aun at all.
check the No. 55 {40 A} fuse inthe undeFhood fuse/relay box.
At the blower motor 2P connec-tor, connecl the BLU/8LK wire terminal to body ground with a
iumper wire.
Turn the ignition switch ON {ll).
Does the blower motor run?
Disconnect the blower motor 2Pconnector, and measure the vol-tage between the BLU/vVHT wireterminal (+) and body ground(-).
ls there battery vokagel
Turn the ignition switch OFF.
Rernove the blower motor relayfrom the under-hood fuse/relaybox and test it (see page 2l-30).
Roplsco tho blower motor .olsy.
Measure the voltage between thoNo. 3 terminal (+) and bodyground (-)
ls there battery voltage?
To page 21- 12
To page 21 13
rD
(cont'd)